Table of Contents
Advertisement
Available languages
Available languages
Alternative method for cutting crown molding
Place the molding at an angle between the fence (12) and the
saw table (11), with the top side of the molding on the table
and the bottom side of the molding on the fence as shown in
fi gure S2.
The advantage to cutting crown molding using this method
is that no bevel cut is required. Minute changes in the miter
angle can be made without affecting the bevel angle. This
way,when corners other than 90º are encountered, the saw
can be quickly and easily adjustedfor them.
Instructions for cutting crown molding angled
between the fence and base of the saw for all cuts
This saw can cut up to 14 mm x 92 mm crown molding nested.
Angle the molding so the bottom of the molding (part
which goes against the wall when installed) is against the
fence (12) and the top of the molding is resting on the saw
table (11), as shown in fi gure S2.
The angled "fl ats" on the back of the molding must rest
squarely on the fence and saw table.
Inside Corner
Left Side
Miter right at 45°
Save right side of cut
Right Side
Miter left at 45°
Save left side of cut
Special Cuts
Never make any cut unless the material is secured on the
table and against the fence.
Bowed material (fi g. T1, T2)
When cutting bowed material always position it as shown in
fi gure T1 and never like that shown in fi gure T2. Positioning
the material incorrectly will cause it to pinch the blade near the
completion of the cut.
Cutting round material
Rounded material should be clamped or held fi rmly to the
fence to keep It from rolling. This is extremely important when
making angle cuts.
Cutting large material (fi g. U)
Occasionally you will encounter a piece of wood a little too
large to fi t beneath the lower guard.
To clear the guard over the wood, with the saw off and your
right hand on the operating handle, place your right thumb
outside of the upper portion of the guard and roll the guard up
just enough to clear the wood, as shown in fi gure U. Release
the guard prior to starting the motor. The guard mechanism
will function properly during the cut. Only do this when
necessary.
Outside Corner
Miter left at 45°
Save right side of cut
Miter right at 45°
Save left side of cut
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD
OPEN WHEN OPERATING THIS SAW.
Warning! Always be sure that the tool is switched off and
unplugged before adjusting or checking the tools function.
After use
After use, wipe off chips and dust adhering to the tool with
a cloth or the like.
Keep the blade guard clean according to the directions in
the previously covered section.
Lubricate the sliding portions with machine oil to prevent
rust.
When storing the tool, pull the carriage toward you fully.
Carrying the tool
Make sure the tool is unplugged.
Secure the blade at the 0° bevel angle and turn the base
to the right mitre angle fully with the slide bar locking scre
(28).
Secure the slide bars after pulling the carriage toward you
fully.
Lower the handle fully and lock it in the position by
pushing in the saw head locking pin (17).
Carry the tool by holding the carry handle (22).
If you remove the clamp, dust bag, etc., you can carry the
tool more easily.
Carry the tool by one hand holding the carrying handle
(22) and one hand holding the tool base.
Caution! Always secure all moving portions before carrying
the tool.
Saw head locking pin (17) is for carrying and storage
purposes only and not for any cutting operations.
Troubleshooting
Problem
Possible Cause
Motor does
Saw not plugged in.
not start
Mitre table
unlocked.
Angle of cut
inaccurate
Too much sawdust
under table.
Parts Failure.
Pivot spring not
Cutting arm
replaced properly
cannot fully
after service.
raise, or blade
guard cannot
Sawdust build up.
fully close
Saw head locking
pin not set properly.
Saw blade
damaged.
Blade binds,
Dull blade.
jams or
shakes
Improper blade.
Warped blade.
ENGLISH
Solution
Check that all cords are plugged in.
Use mitre table locking lever (see
Adjusting the mitre angle section.
Vacuum or blow out dust. Wear eye
protection.
Contact service centre.
Contact service centre.
Clean and lubricate moving parts.
Check, adjust, and properly set saw
head locking pin.
Replace blade.
Replace or sharpen blade.
Replace blade.
Replace blade.
17
Advertisement
Table of Contents
