Table of Contents
Advertisement
ENGLISH
Remove hand from guard lever and firmly grip secondary
u
arm to allow you to resist kickback if it occurs.
Make sure blade is not in contact with cutting surface
u
before starting saw.
Start the motor, allow saw to come to full speed, and then
u
material to be cut. Advance saw along the cutting line until
Release trigger and allow blade to stop completely before
u
withdrawing the blade from the material.
When starting each new cut, repeat as above.
u
Troubleshooting
Problem
Possible Cause
Battery pack not
Unit will not start.
installed properly.
Battery pack not
charged.
Battery pack not
Battery pack will
inserted into charger.
not charge.
Charger not plugged in.
Surrounding air
temperature too hot or
too cold.
Battery pack has
Unit shuts off
reached its. maximum
abruptly.
thermal limit.
Out of charge. ( To
maximize the life of the
battery pack it is
designed to shutoff
abruptly when the
charge is depleted.)
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
10
(Original instructions)
Possible Solution
Check battery pack
installation.
Check battery pack
charging requirements.
Insert battery pack into
charger until LED appears.
Plug charger into a
working outlet. Refer
to "Important Charging
Notes" for more details.
Move charger and battery
to a surrounding air
teperature of above 40
degrees F (4.5°C) or
below 105 degrees F
(+40.5°C).
Allow battery pack to cool
down.
Place on charger and
allow to charge.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and re-
cycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
address indicated in this manual. Alternatively, a list of author
ised BLACK+DECKER repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
Input voltage
No-load speed
Max depth of cut
Max depth of cut at 45º bevel
Blade diameter
Blade bore
Blade tip width
Weight
L
(sound pressure) 76.0 dB(A), Uncertainty (K) 3 dB(A)
pA
L
(sound power) 87.0 dB(A), Uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 60745:
Cutting wood (a
) 1.5 m/s
h, W
BDCCS18
V
18
ac
min
3700 RPM
-1
mm
43
mm
35
mm
140
mm
12.7
mm
2.0
kg
2.5
2
2
, uncertainty (K) 1.5 m/s
Advertisement
Table of Contents
