Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Watson Marlow Pumps 501CC
Summary of Contents for Watson Marlow Pumps 501CC
- Page 1 501CC 501cc-gb-02.pdf...
- Page 2 501DF, 501DP, 501DFX, 501DV ATEX II 2 G T4 501F, 501P, 501X, 501V ATEX...
-
Page 3: Two Year Warranty
Declarations Declaration of When this pump unit is used as a stand alone pump it complies with: conformity Machinery Directive 2006/42/EC, EMC Directive 2004/108/EC. Declaration of When this pump unit is to be installed into a machine or is to be assembled with other machines for installations, it must not be put into service until the relevant machinery has Incorporation been declared in conformity with the Machinery Directive 2006/42/EC. -
Page 4: Installation
use valves with a straight fluid path. use slow sweeping bends with minimum radius equal to four to five times the tubing diameter. keep the pumphead rollers and track clean. The self-priming nature of peristaltic pumps means valves are not required. Any valves fitted must cause minimum restriction to flow in the pumping circuit. -
Page 5: Troubleshooting
Start up Before starting and after prolonged storage of the gear units, remove the plug from the vent screw on top of the casing to avoid excessive pressure in the gearbox, which may cause leakage at the shaft seals. Troubleshooting Should the pump fail to operate, make the following checks to determine whether or not servicing is required. -
Page 6: Pump Specifications
Installation A muffler is supplied with the air motor, but not installed. Install a moisture trap and filter in the air line ahead of the motor. If condensates need to be flushed out of the motor, use clean, dry air at low pressure. For efficiency of output and speed control, use air lines of the same size or next pipe size larger than the intake port of the motor. - Page 7 501RLC Installation. Simplex (single pumphead) units and duplex (twin pumphead) units Isolate motor from mains supply. Fit the track in any one of three orientations, over the drive shaft and locating boss. Secure the track with the four locating screws. Ensure the drive shaft is degreased before locating the rotor onto the shaft via the split collet.
- Page 8 501RLC tube loading. Duplex (twin pumphead) units Isolate the pump from mains supply. Unlock and open the hinged guard. Swing out the rotor crank handle until it locks into position. Loosen the rotor screw and give the rotor a sharp tap to release it. Pull the rotor slightly forward from its seated position on the drive shaft so that the pinned collet clears the drive shaft dog and it can rotate freely .
- Page 9 501RLC Pumphead spares Number Spare Description MN 1200M Lockable guard FN 4502 Lock FN 2341 Hinge screw MN 0266M Hinge grey MNA0114A Tube clamp assembly FN 2332 Screw FN 0422 Screw (x 4) MN 0011T Main roller MNA0143A 501RLC Rotor assembly MNA0511A 501RL2C Rotor assembly SG0001...
-
Page 10: Technical Data
Technical Data # # # # # (165) (165) English Tube number Tube bore Pressure(+) Suction Counter-clockwise Clockwise (rpm) Gearbox lubricant Mineral Oil Energol GR-XP 220 Mobil-gear 630 Shell Omala Oel 220 EnergolGR-XP 100 Mobil-gear 629 Shell Omala Oel 100 Bartran HV15 Mobil DTE 11M Shell Tellus Oel T 15... - Page 11 501RLC, 501RLC2 (ml/min) Flow rates “ 1/50 1/32 1/16 3/16 5/16 1400 2100 1200 1900 2900 1400 2200 1100 1800 2800 6 - 60 0.25-2.5 0.74-7.4 2.6-26 11-110 24-240 38-380 60-600 21 - 213 0.88-8.9 2.6-26 9.0-91 39-400 85-860 130-1400 210-2100 29 - 291 1.2-12...
- Page 12 501RLC, 1.6mm Product codes “ Marprene Bioprene Pumpsil 0.5 1/50 902.0005.016 903.0005.016 913.0005.016 0.8 1/32 902.0008.016 903.0008.016 913.0008.016 1.6 1/16 902.0016.016 903.0016.016 913.0016.016 902.0032.016 903.0032.016 913.0032.016 4.8 3/16 902.0048.016 903.0048.016 913.0048.016 902.0064.016 903.0064.016 913.0064.016 8.0 5/16 902.0080.016 903.0080.016 913.0080.016 “ Tygon Fluorel Neoprene...
- Page 13 501RLC Flow rates...
- Page 14 501F/R 501DF/R 62rpm model 223 rpm model 501FX/RL...
- Page 15 Switch Watson-Marlow, Bioprene, Pumpsil and Marprene are trademarks of Watson-Marlow Limited. Tygon is a trademark of the Saint-Gobain Performance Plastics Company. Fluorel is a trademark of 3M. Sta-Pure and Chem-Sure are trademarks of W.L Gore and Associates. Warning, These products are not designed for use in, and should not be used for patient connected applications. The information contained in this document is believed to be correct but Watson-Marlow Limited accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
- Page 17 Product use and decontamination declaration In compliance with the UK Health & Safety at Work Act and the Control of Substances Hazardous to Health Regulations you, the user are required to declare the substances which have been in contact with the product(s) you are returning to Watson-Marlow or any of its subsidiaries or distributors.
Need help?
Do you have a question about the 501CC and is the answer not in the manual?
Questions and answers