SloanLED PrismBEAM24 Install Manual

SloanLED PrismBEAM
Installation Guide for 701972-(CC)24P(D,S)(X)1
WARNING: Risk of electrical shock. New installation and LED Retrofit Kit installation requires knowledge of sign electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
Follow all NEC and local codes. SloanLED PrismBEAM
installation et l'installation du kit de modification à LED nécessitent la connaissance des systèmes électriques de signalisation. Si non qualifié, ne tentez pas l'installation. Contactez un électricien qualifié. Suivez
tous les codes NEC et locaux. SloanLED PrismBEAM
For New Installation, proceed with Step 1 below. For Retrofit Installations, begin with Retrofit Instructions on page 3.

New Installation

1. Tools required:

1. Measuring tape
2. Wire strippers
3. Gloves
4. Drill
5. Screwdriver
Lampholder Bracket
3. Install fluorescent lampholders or SloanLED PrismBEAM
Brackets (P/N 402607) 12" (305 mm) center-to-center along
returns of cabinet (see Layout Guidelines on page 2).
is not suitable for submersion or direct exposure to water for extended periods of time. AVERTISSEMENT: Risque de choc électrique. La nouvelle
24
ne convient pas à la submersion ni à l'exposition directe à l'eau pendant de longues périodes.
24
WARNING: Use SloanLED PrismBEAM
Power Supply only. AVERTISSEMENT: Utilisez uniquement le
SloanLED PrismBEAM
uniquement.
Optional: Bracket designed to
mount over existing lampholders
to provide greater stability, at the
installer's discretion.
24
24
with 100 W 24 VDC
24
avec une alimentation 100 W 24 VDC
24
Lampholders Brackets
Lamp Lengths
Nominal
18" (0.46 m)
24" (0.61 m)
30" (0.76 m)
36" (0.91 m)
42" (1.07 m)
48" (1.22 m)
60" (1.52 m)
NOTE: End cap adds exactly 0.50" (12.7 mm) to length of extrusion.

2. Components list:

• SloanLED PrismBEAM
Double-sided assemblies:
model numbers 701972-(CC)24PD(X)1
Single-sided assemblies:
model numbers 701972-(CC)24PS(X)1
• Power supplies: SloanLED 24 V Class 2
output power supply (refer to "SloanLED
Power Supply Guide for Sign Products"
for appropriate 24 V power supply models)
• UL approved 18 AWG (1 mm
diameter supply wire
• UL approved wire connectors appropriate
for wire gauge used
• Optional: Electrical grade silicone,
4" (101.6 mm) nylon zip ties, conduit and
conduit connectors (water tight if necessary)
NOTE: Lamps must be mounted in an
enclosed sign. This product is not suitable
for immersion or direct exposure to water
for extended periods of time.
4. Determine lengths and quantities of
SloanLED PrismBEAM
(see Power Supply capacity table on
page 4). Determine quantity of brackets
(P/N 402607): Two (2) per
SloanLED PrismBEAM
Actual Nominal
64" (1.63 m)
15.72" (0.40 m)
21.72" (0.55 m) 72" (1.83 m)
27.72" (0.70 m) 84" (2.13 m)
33.72" (0.86 m) 96" (2.44 m) 93.72" (2.38 m)
39.72" (1.01 m) 108" (2.74 m) 105.72" (2.69 m)
117" (2.97 m) 114.72" (2.91 m)
45.72" (1.16 m)
57.72" (1.47 m) 120" (3.05 m) 117.72" (2.99 m)
assemblies:
24
) or larger
2
24
assembly.
24
Actual
61.72" (1.57 m)
69.72" (1.77 m)
81.72" (2.08 m)
PAGE 1 OF 4