However, like all electronic equipments, the AV-GM0803-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
Furthermore, the built-in IR extension function makes users at display site access the DVD player, PS3 or any HDMI supported devices directly! In addition, AV-GM0803-S1 also supports PoC (Power over Cable) which can power both units from TX with power supply.
* Additional IR remote controllers and IR blasters can be purchased as optional accessories to control the HDMI sources located separately. SPECIFICATIONS Model Name AV-GM0803-S1 Technical AV-GM0803-S1 CV-745V True 8x8 matrix switcher Role of usage Receiver [RX] Transmitter [TX] HDMI Deep Color & full 3D...
-20~60°C [-4~140°F] Relative humidity 20~90% RH [no condensation] PANEL DESCRIPTIONS Transmitting unit ► AV-GM0803-S1 Front Panel Source Status: Input source indicator LED IR SENSOR: IR sensor for receiving the IR commands from IR remote Output Push Button & 7-segment LED: Front panel push buttons used to select the number of display channel &...
LED: Link indicator RJ-45: HDBT output port 1-8 IR Blaster 1-8: 3.5mm IR blaster socket for individual HDMI source control INPUT 1-8: HDMI inputs System IR Receiver: Ext. IR receive All IR Output: 3.5mm IR blaster socket for HDMI source control on all 4 inputs Receiving unit ►...
IR BLASTER: IR control on individual display device IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR remote controls of AV-GM0803-S1 and all other HDMI source devices. CAUTION! Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders.
You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work. CONNECTION DIAGRAM...
OPERATION APPROACH Method A: Push-in Button preset save learn default 1. IN/OUT MAP 1) Use the “+”or “-“ output push button to select the number of display 2) Use the “+”or “-“ input push button to select the number of input source “+”: change selected input/output port in ascending order “-”...
Page 10
4) If you push the “output+ (save)”button before the mapping setting is effective, the LED will show “一”“一”to quit the Preset Mapping Mode 4. Default EDID Mode 1) Push “input+(default)”button to select the input channel which you want to learn default EDID and then keep pushing “input+(default)”button when you select your desired input channel 2) Push the “+”or “-”...
Page 11
Method B: IR Remote Control 1. IN/OUT Switch Operation Procedure 7-Segment LED IN/OUT Switch Output Number (1~8) + Input Number (1~8) 1. Press output number key “3” to select Output 3 Ex: Input 2 To Output 3 2. Press input number key “2” to select Input 2 2.
Page 12
DEFAULT EDID Begin default EDID selection LEARN EDID Begin EDID learning from one output CLEAR Clear the previous IR operation procedure TAKE Trigger the previous setting Reserved Reserved Operation Procedure 7-Segment LED Output Status Status + Output Number (1~8) + Take 1.Press “STATUS”...
Page 13
2. Press output number key “3” to select Output 3 3.Press “TAKE” button Method C: Software Control through RS-232 port / Ethernet port 1. System Requirement 1) OS Information: MS WinXP/7 2) Baud rates: 9600 3) Software size: 3 MB 4) Minimum RAM requirement: 256 MB Method D: Software Control through RS-232 port I/O Routing Button...
b) Click “Save” button to save current mapping 3) Preset Mapping: a) Select Mapping(1-8) a) Click “Recall” button to recall previous mapping which are saved 2. Rename I/O Button 1) Rename I/O: a) Rename output name...
b) Rename input name 2) Rename Mapping: a) Rename Mapping name 3. EDID Button...
Page 17
1) Learn EDID from Default a) Select Default EDID(1-8 Default EDID) b) Select Input c) Click “Learn” button to learn default EDID 2) Learn EDID From Display a) Select output b) Select Input c) Click “Learn” button to learn display EDID 3) Load EDID File to Input a) Select Input b) Click “Load”...
b) Select the EDID content c) Click “Save EDID on Computer” to save the generated EDID as a file 4. Network Button...
Page 19
a) DHCP mode => Click DHCP and then click the “Read Setting” button to get the IP address Info b) Static mode => Click Static and then key in the “IP”, “MASK”, ”GATEWAY” info. After setting IP Address, please click “Save Setting” to save IP address Info c) Save Setting =>...
Page 20
5. System Button a) Version: => To get the F/W version information b) Factory Reset c) Help => To view the steps of the firmware update d) Web Password => Change the web password e) Firmware Update Main Board f) Firmware Update Web IC g) Firmware Update DB Board h) Firmware Update Valens...
6. Refresh COM Port Button 7. COM Port Selection Click “ ” button to select COM Port 8. Connection Status 1) Connected Status: 2) Connecting Status: 3) Disconnected Status: 9. Connect/Disconnect Button Click this button “ ” to change connection status 10.
Page 23
Method E: Web Interface Control The default IP address: 192.168.1.111 Account: admin Password: matrix I/O Routing Button Setting Button EDID Button Refresh I/O Status & Read I/O Name Button 1. I/O Routing Button 1) I/O: a) Select the input 2) Save Mapping: a) Select Mapping(1-8) b) Click “Save”...
Page 24
2. Setting Button 1) Rename I/O: a) Rename output name b) Rename input name c) “Read” button: to read I/O name from device d) “Send” button: to send the changed I/O name to device 2) Rename Mapping: a) Rename Mapping name b) “Read”...
Page 25
3. EDID Button 1) Learn EDID from Default a) Select Default EDID(1-8 Default EDID) b) Select Input c) Click “Send” button to learn default EDID...
Page 26
2) Learn EDID From Display a) Select output b) Select Input c) Click “Send” button to learn display EDID 4. Refresh I/O Status Button...
EDID LEARNING The EDID learning function is only necessary whenever you encounter any display on the HDMI output port that cannot play audio and video properly. Because the HDMI source devices and displays may have various level of capability in playing audio and video, the general principle is that the source device will output the lowest standards in audio format and video resolutions to be commonly acceptable among all HDMI displays.
The quality of output video is not good enough, how can I do? Please adjust the 8-level equalization on the receiver units. The HDMI signal level varies from 0 (strongest) to 7 (weakest) for respective transmission length from longest possible range to short distance.
format. Therefore if the TV cannot decode 7.1ch audio, there is definitely no audio. NOTICE 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI/HDMI EDID information. 2. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz LAN cable and ASTRODESIGN Video Signal Generator VG-859C &...
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the AV-GM0803-S1 features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM0803-S1 and is the answer not in the manual?
Questions and answers