go-e Gemini flex Installation And Operating Manual
Hide thumbs
Also See for Gemini flex:
- Installation and operating manual (34 pages) ,
- Quick reference manual (24 pages) ,
- Quick reference manual (21 pages)
Table of Contents
Related Manuals for go-e Gemini flex
Summary of Contents for go-e Gemini flex
- Page 1 Installation and operating guide go-e Charger Gemini flex 11/22 kW Mobile Wallbox for Electric Vehicles - IC-CPD valid for article numbers: CH-04-11-01, CH-04-22-01 Installation and Operating Guide go-e Charger Gemini flex V 1.2...
-
Page 2: Table Of Contents
Symbols page 4 Sustainable charging page 4 Before installation and commissioning/download page 6 Safety regulations/notes page 6 Product overview page 10 Scope of delivery page 11 Technical data page 12 Installation page 15 Commissioning/charging page 18 LED status display/troubleshooting page 20 Reset card/RFID chip page 24 page 26... -
Page 3: Symbols
In order to save energy are constantly developing the firm- and thus also to charge in an environ- We wish you lots of fun with your go-e The charging unit was developed ware and adapting the app to the... -
Page 4: Before Installation And Commissioning/Download
The go-e Charger Gemini flex has communication interfaces WiFi Download the data sheet: the go-e Charger if the housing is dama- 802.11b/g/n 2.4GHz and RFID. WiFi is www.go-e.com ged or open. operated on a frequency of 2.4Ghz, channels 1-13 with the frequency band In case of unusual heat development, do 2412-2472Mhz. - Page 5 The go-e Charger Gemini flex 11 kW may using an adapter with domestic plug. If water. only be operated at the following con-...
-
Page 6: Product Overview
Required for using the app and for resetting the charger to factory settings 16/32 A CEE red plug (Gemini flex 11/22 kW) Connection to red CEE socket or original go-e adapter Wall bracket Mounting material Housing 5x Dowel 8 x 40 mm Impact-resistant and UV-resistant high-performance plastic 4x Screws for wall bracket 4.5 x 50 mm... -
Page 7: Technical Data
Maximum 2,000 m above sea level suitable for permanent outdoor operation Relative humidity Not more than 95 % (non-condensing) For authorised access by the electricity grid operator to the go-e Charger go-e network operator API for grid-serving power control Impact resistance... -
Page 8: Installation
Required tools CEE red 16 A (3-phase) CEE red 32 A (3-phase) With original go-e adapters (not included in the scope of delivery, available as accessories): to CEE red 32 A to CEE red 16 A (three-phase - limitation by charging station to 16 A) - Page 9 8. Installation 8. Installation Drill holes at the four marked positions. The go-e Charger is equipped with an integrated DC protection module with direct current detec- tion and additional AC detection (6 mA DC, 20 mA AC). On the building side, an RCD type A and a circuit breaker must be installed.
-
Page 10: Commissioning/Charging
LEDs corresponds to the set charging current. Five predefined charging levels can be selected via the but ton. 1 LED = 1 A Gemini flex 11 kW = 6 A - 16 A Gemini flex 22 kW = 6 A - 32 A... -
Page 11: Led Status Display/Troubleshooting
„ground check“, which prevents the char- the „cable release“ function of your vehicle or ging process in TT/TN power grids (common the large round button of the go-e Charger app in most European countries) in case of in- (tab „Charging“). - Page 12 Try to insert it into the yellow statically at the bottom. type 2 socket as far as possible. Check whether the supply line to the go-e Char- ger is properly grounded. Firmware update The LEDs flash pink and turn yellow with increa- Phase error sing progress of the update.
-
Page 13: Reset Card/Rfid Chip
If the charger does not leave this mode, the WiFi Protection against unauthorised charging signal may be disturbed. Please remove possi- If you install the go-e Charger outdoors, you can ble sources of interference (e.g. devices with a protect the device against use by unauthorised WiFi mesh network). -
Page 14: App
12. App - connection setup 12. App - connection setup Set up connection via WiFi The go-e Charger can also be used without an app. For remote control of the charger and for some comfort functions, a WiFi connection of the Download the go-e Charger app if you want to charger is essential. - Page 15 12. App - charging 12. App - settings The „Charging“ tab of the go-e Charger app gi- ves you direct access to the most important You can adjust the basic and comfort settings of functions for starting, stopping and monitoring the charger via the „Settings“...
-
Page 16: Warranty And Exclusion
In the (justified) case of common at the end of the working day and take the return of the defective product to go-e, go-e will bear the costs incurred. If, in the event of a electricity that could otherwise not be used sen- guarantee claim, it becomes apparent that the device needs to be replaced, the customer waives sibly. -
Page 17: Ce Declaration Of Conformity
CE Declaration of Conformity: Hereby go-e GmbH declares that the radio equip- Do you still have questions about the go-e Charger? ment type go-e Charger Gemini flex 11 kW and go-e Charger Gemini flex 22 kW is in compliance with Directive 2014/53/EU. The full text of the EU Declaration...
Need help?
Do you have a question about the Gemini flex and is the answer not in the manual?
Questions and answers