Summary of Contents for Backyard Discovery SWEETWATER HEIGHTS 2303027
Page 1
MANUFACTURED BY: Backyard Discovery 3305 Airport Drive, Pittsburg, KS 66762 800-856-4445 Basepoint Business Centre: Rivermead Drive,Westlea, Swindon SN5 7EX Phone: 0800-118-2476 J.P. Coenstraat 7, The Bridge, The Hague, 2595 WP, Netherlands Phone: 0800-567-8990 SWEETWATER HEIGHTS PLAYHOUSE MODEL # 2303027 The assembly manual must be retained since it contains important information WARNING Adult Assembly Required.
Page 2
Owner's Manual Basic Setup Dimensions & Assembly Notes Selecting the correct location for your play product is important for your children’s safety and the product’s longevity The safe play area refers to a zone extending 6'-7" (2m) beyond the play product on all sides, including the space •...
Page 3
Parts Identification Owner's Manual Wood Components (Not to Scale) LEFT FRONT UPRIGHT - W4L17837 1 3/8"x3 3/8"x62 3/8" (36x86x1584) (x1) RIGHT FRONT UPRIGHT - W2A03762 1 3/8"x3 3/8"x62 3/8" (36x86x1584) (x1) RIGHT REAR UPRIGHT - W4L17839 1 3/8"x3 3/8"x62 3/8" (36x86x1584) (x1) LEFT REAR UPRIGHT - W4L17840 (x1)
Page 6
Parts Identification Owner's Manual Wood Components (Not to Scale) FRONT RIGHT CORNER PANEL - W2A03848 REAR RIGHT CORNER PANEL - W2A03851 (x1) (x1) FRONT LEFT CORNER PANEL - W2A03854 REAR LEFT CORNER PANEL - W2A03857 (x1) (x1) REAR CENTER PANEL - W2A03860 LEFT CENTER PANEL - W2A03861 1 1/4"x18 7/8"x20 7/8"...
Page 10
Owner's Manual Parts Identification Accessory Components (Not to Scale) A100028 A4M00555 HAND GRIP GREEN PLASTIC 90° L-BRACKET - BLK (x2) (x8) A4M00528 BYD ID TAG (MEDIUM) AGES 2 TO 10 (x1) A100361 PLASTIC SUNBURST (x2) A4M01047 L BRACKET 2.5x38x55x55 (x3) A6P00024 FAUCET KIT A6P00032...
Page 11
Owner's Manual Parts Identification Accessory Components (Not to Scale) A4M00624 A4M00994 HINGE (DOOR, SPRING LOADED) HINGE (DOOR, NON-SPRING LOADED) (x1) (x1) A4M00933 DOOR STOP (x1) A4M01045 BELL ASSEMBLY (x1) A6P00391 6 FT SLIDE BED (x1)
Page 12
Owner's Manual Parts Identification Accessory Components (Not to Scale) A6P00330 INDUCTIVE BURNER KIT (x1) A6P00335 STOVE BASE (x1) A6P00338 FRY PAN (x1) A6P00331 BLENDER (x1) A6P00336 BOIL POT (x1) A6P00339 SPATULA (x1) A6P00337 POT/PAN LID (x2) A6P00340 LADLE (x1)
Page 13
Electronics Safety Warnings Owner's Manual CLASS B DIGITAL DEVICE STATEMENT Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PRE-ASSEMBLY STEP 1 - SORTING PARTS It is critical for ease of assembly that you take the time to sort and organize the wood and hardware. WOOD PARTS: • Organize wood parts by the three-digit, alpha-numeric number stamped on each board (ex. P01). •...
Page 15
PRE-ASSEMBLY STEP 2 - TOOLS REQUIRED Drill Attachments: Phillips Head Open End Wrenches 1/2" & 9/16" 1/8", 3/16", 3/8" & 7/16" Drill Bits 3/8" Drive Ratchet, 1/2" & 9/16" STD Sockets 1/2" & 9/16" Deep Sockets Phillips Screw Driver Cordless Drill or Electric Drill Rubber Mallet - Optional Claw Hammer...
Page 16
PRE-ASSEMBLY STEP 3 - CHOOSE YOUR ASSEMBLY METHOD There are several types of assembly instructions available to you. 1. Printed Assembly Manual included with your set 2. BILT APP - 3D interactive instructions 3. Combination of the Printed Manual and BILT APP (Note: Step numbers can differ between the two methods)
Page 17
SLIDE ASSEMBLY STEP 1 SLIDE BRACE - W4L13297 5/8"x3 3/8"x14 1/4" (16x86x362) A6P00391 6 FT SLIDE BED H100396 BOLT WH BLK H100379 T-NUT BLK 5/16x1/2 5/16 PLACE 'M77' SLIDE BRACE BOARD 1/2" FROM THE BOTTOM EDGE OF THE SLIDE BED. USING THE BOARD AS A TEMPLATE, MARK WHERE THE PILOT HOLES WILL BE DRILLED.
Page 18
SLIDE ASSEMBLY STEP 2 A6P00390 6 FT SLIDE RAIL RIGHT SLIDE BRACE - W4L13298 5/8"x3 3/8"x14 1/4" (16x86x362) A6P00389 6 FT SLIDE RAIL LEFT H100201 SCREW PFH BLK (16) 8x2-1/2 NOTE: 1. PLACE THE SLIDE RAIL ON FLAT SURFACE. STARTING AT THE BOTTOM, INSERT THE SLIDE BED INTO THE CHANNEL ON THE INSIDE OF THE RAIL.
Page 40
PLAYHOUSE STEP 1 ASSEMBLY FRONT RIGHT CORNER PANEL - W2A03848 REAR RIGHT CORNER PANEL - W2A03851 (x1) (x1) FRONT LEFT CORNER PANEL - W2A03854 REAR LEFT CORNER PANEL - W2A03857 (x1) (x1) NOTE: STAND THE (4) CORNER WALL (x1) ASSEMBLIES AS SHOWN BELOW. LEFT BACK NOTE THE PROFILE OF...
Page 41
PLAYHOUSE STEP 2 ASSEMBLY H100385 SCREW PFH BLK (x12) LEFT CENTER PANEL - W2A03861 1 1/4"x18 7/8"x20 7/8" (32x478x536) (x1) (x12) SCREW - 1" BACK LEFT (x1) FRONT RIGHT...
Page 42
PLAYHOUSE STEP 3 ASSEMBLY H100385 SCREW PFH BLK (x12) REAR CENTER PANEL - W2A03860 (x1) 1 1/4"x18 7/8"x20 7/8" (32x478x536) (x12) SCREW - 1" (x1) BACK LEFT RIGHT FRONT...
Page 43
PLAYHOUSE STEP 4 ASSEMBLY H100201 SCREW PFH BLK (x4) 8x2-1/2 HEADER ASSEMBLY - W2A03862 (x2) ALL INTERIOR SURFACES ARE FLUSH. (x4) (x1) SCREW - 2 1/2" LEFT BACK (x1) RIGHT FRONT...
Page 44
PLAYHOUSE STEP 5 ASSEMBLY H100387 SCREW PFH BLK (x32) 8x1 1/4 TIE STRAP - W4L17870 5/8"x3 3/8"x3 3/8" (16x86x86) (x8) (x8) INSTALL WITH THE EDGE SURFACE OF 'N1' FLUSH WITH THE END OF WALL BOARD, AS SHOWN. (x32) SCREW - 1 1/4" DRILL 1/8"...
STOVE ASSEMBLY A6P00330 INDUCTIVE BURNER KIT (x1) A6P00335 STOVE BASE (x1) FCC LABEL NOTE: -DO NOT MIX OLD AND NEW BATTERIES. -DO NOT MIX ALKALINE, STANDARD (CARBON-ZINC), OR RECHARGEABLE (NI-CAD, NI-MH, ETC.) BATTERIES. -NON-RECHARGEABLE BATTERIES ARE NOT TO BE RECHARGED. -ONLY BATTERIES OF THE SAME OR EQUIVALENT TYPE AS RECOMMENDED ARE TO BE USED.
Page 66
FINAL ASSEMBLY STEP 2 H100382 SCREW PFH BLK H100408 SCREW PWH BLK (x8) 8x1 3/4 (x8) 8x1/2 PLAYHOUSE SUBASSEMBLY (x1) (x4) SCREW - 1 3/4" PICKET MAY NEED TO BE TEMPORARILY REMOVED TO ASSEMBLE THE HOUSE TO THE DECK. (x8) SCREW - 1/2"...
Page 67
FINAL ASSEMBLY STEP 3 H100202 SCREW PWH BLK (x2) 8x5/8 A4M00528 BYD ID TAG (MEDIUM) AGES 2 TO 10 (x1) (x2) SCREW - 5/8" (x1) BYD ID TAG (MEDIUM) AGES 2 TO 10 12 1/4 in [312 mm]...