Continuous Recording (Clip Continuous Rec) (Exfat) - Sony PXW-Z190 Operating Instructions Manual

Configuring before shooting
Configure Interval Rec (page 103) in the
Recording menu before shooting.
When Setting is set to On, Interval Rec mode is
activated and "Int Stby" appears on the screen.
When a video light compatible with the Multi
Interface Shoe is mounted, you can set Interval
Rec >Pre-Lighting in the Recording menu to On
so that the light turns on automatically 2 seconds,
5 seconds, or 10 seconds before recording starts.
Note
• When Pre-Lighting is set to On, the video light remains
turned on if the video light off time would be less than
5 seconds, according to the Interval Time setting, even
when Video Light Set is set to Rec Link or Rec Link +
Stby in the Camera menu.
Recording in Interval Rec mode
Start the recording after completing the required
setting.
Press the record button.
When you start recording, the "Int Stby"
indication changes and alternates between "Int
zRec" and "Int zStby."
Notes
• While recording in Interval Rec mode, the Interval
Time and Number of Frames settings cannot be
changed. To change the settings, first stop recording.
• After starting recording in Interval Rec mode, Rec
Review operation is disabled, including during the
interval time.
• The timecode is recorded in Rec Run mode during
recording in Interval Rec mode (page 102).
• Some extra frames may be recorded if you stop
recording or switch the card slot while recording is
halted in Interval Rec mode.
• Interval Rec >Setting is automatically set to Off when
the ON/STANDBY switch is set to the STANDBY
position. However, the Interval Time and Number of
Frames settings are maintained.
Continuous recording (Clip
Continuous Rec) (exFAT)
Normally, a clip is created as an independent file
each time you start and stop recording. However,
Clip Continuous Rec mode allows you to start and
stop recording while continuously recording to
the same clip, for as long as the function remains
enabled.
This is convenient when you do not want to
generate a large number of short clips, and when
you want to record without worrying about
exceeding the clip limit. It is still easy to find
recording start points, because a Rec Start mark is
recorded at the recording start point each time you
start recording.
For details about recording formats compatible
with Clip Continuous Rec, see (page 126).
Configuring before shooting
Configure Clip Continuous Rec (page 103) in the
Recording menu before shooting.
When Setting is set to On, Clip Continuous Rec
mode is activated and "Cont Stby" appears on the
screen (page 12).
Configuring using assignable buttons
You can assign Clip Continuous Rec to an
assignable button (page 38), and switch Clip
Continuous Rec mode On/Off by pressing the
button.
Notes
• Clip Continuous Rec cannot be set to On at the same
time as Interval Rec, Picture Cache Rec, S&Q Motion,
2-slot Simul Rec, or 4K & HD (Sub) Rec (when MPEG
HD upgrade license (option) is installed). When Clip
Continuous Rec is set to On, these other recording
modes are forcibly set to Off.
• Clip Continuous Rec mode cannot be used while
recording.
Recording in Clip Continuous Rec mode
Start the recording after completing the required
setting.
Press the record button.
When you start recording, the "Cont Stby"
indication changes to "Cont zRec" (z turns red).
Notes
• During recording or in recording standby mode (when
the "Cont Stby" indication is displayed), if you remove
the memory card, the battery, or the power source, the
memory card needs to be restored. Cancel Clip
Continuous Rec mode and then remove the memory
card. When "Cont Stby" indication is flashing (once
per second), you can remove the memory cards.
• Stop the recording after recording for two or more
seconds.
To exit, stop the recording.
40