ABB UNO-DM-2.0-TL-PLUS Manual page 149

INVERTER RUN
- PRODUCTION -
N.C.
Relay State: Switched
N.O.
GRID DISCONNECTION
- NO PRODUCTION -
N.C.
Relay State: Idle
N.O.
GRID RECONNECTION
t=based on Country Standard
N.C.
Relay State: Idle
N.O.
DISCONNECTION
Yes No
CAUSE IS STILL
PRESENT
INVERTER RUN
N.C.
Relay State: Idle
N.O.
ERROR OCCURENCY
ERROR MESSAGE
t=15s
N.C.
Relay State: Switched
N.O.
GRID RECONNECTION
t=based on Country Standard
N.C.
Relay State: Idle
N.O.
ERROR
Yes No
STILL
PRESENT
In the presence of W003, W004, W005, W006, W007 signalling, the alarm contact switches
to then reset itself at the end of the alarm signal. This means that during the absence of grid
voltage (display message "Missing Grid") the alarm contact remains in its resting position.
10. Alarm
This features will work only on inverter equipped with UNO-DM-COM KIT
(-X models) or UNO-DM-PLUS-COM ETHERNET KIT (-E models).
This section of the menu allows you to set the activation status of a relay
(available either as contact normally open – N.O. - and as a normally
closed contact -N.C.) and to configure customised alarm conditions.
This contact can be used, for example, to: activate a siren or a visual alarm,
control the disconnect device of an external transformer, or control an exter-
nal device.
Relay switching can be set in 9 different modes using the submenu Set
Alarm Type (For the "Alarm Conf.", "Al. Conf. Latch", "Al. Conf. Ext.",
"GoGo Rel(Auto)" and "GoGo Rel(Remote)" it is possible to configure
customised alarm conditions through the submenu Alarm Config:
• Production (display text "Production")
The relay is activated (status: switched) whenever the inverter connects
to the grid; as soon as the inverter is disconnected from the grid (for
whatever reason that caused disconnection), the relay is in its resting
position.
• Alarm with reset at the end of the alarm signalling process (display
text "Alarm"):
The relay is activated (status: switched) whenever an error (code Exxx)
or warnings related to grid parameters out of range (Warning – codes
W003, W004, W005, W006, W007) are present on the inverter. The
alarm returns to its resting position when the alarm signal ends, i.e. be-
fore the inverter checks the grid parameters after the alarm state. This
is because grid control state is not an alarm state but a state of normal
operation.
Alarms for which the relay is activated
E001 E002
E007 E010
E015 E016
E021 E022
E028 E029
E034 E035
E051 E053
E058 E065
E070 E074
E086 E087
W002 W003
W009 W011
W021 W022
W030 W036
W043 W046
W059
- 149 -
E003 E004 E005
E011 E012 E013
E017 E018 E019
E023 E025 E026
E030 E031 E032
E036 E037 E046
E054 E055 E056
E066 E067 E068
E077 E078 E080
E088 E089
W004 W005 W006
W015 W017 W018
W023 W024 W027
W037 W039 W040
W047 W048 W051
7 - Operation
E006
E014
E020
E027
E033
E050
E057
E069
E084
W007
W019
W029
W042
W058