Subscribe to Our Youtube Channel
Related Manuals for Breas Z2
Summary of Contents for Breas Z2
- Page 1 CPAP System ® CONTINUOUS POSITIVE AIRWAY PRESSURE SYSTEM User Guide Breas Medical, Inc. N. Billerica, MA 01862 User Guide English Z2 User Guide v1 10122021 #40-0110 Rev. D...
-
Page 2: Table Of Contents
Q-lite™ is a trademark of Breas Medical, Inc . Z2®, PowerShell®, NiteLog® and Z-Breathe® are registered trademarks of Breas Medical, Inc . Breas and the Breas logo are trademarks of Breas, AB . All other trademarks are the property of their respective owners . -
Page 3: Welcome To Your Z2 Cpap System
. Medical Information • Auto Altitude Adjustment – the Z2 adjusts to altitudes up to 8000 ft above sea level . Indications for Use • Air Travel – The Z2 adjusts to an airplane’s cabin pressure and is approved for use on Your Z2 CPAP System is a single user, reusable device that provides continuous positive airway airplanes . -
Page 4: Z2 Warnings And Cautions
. the mask vent holes . However, when the Z2 is not operating properly (e . g . , at low pressure) or the Z2 is off, insufficient fresh air may be provided through the mask and •... -
Page 5: Getting To Know Your Z2 Cpap System
End Cap is not properly installed . The Z2 System is provided with a 4 ft slim style CPAP Tube . The CPAP Tube connects the Z2 to your • The temperature of the airflow for breathing produced by CPAP devices can be higher than mask . -
Page 6: Filter
USB A to Micro B Cable 4 . Place all the components in an area where you can easily access the Z2 for set up and The USB Cable allows the Z2 to communicate with a computer to collect and view user data . It programming . -
Page 7: Using Your Z2
. The display will read 0 . 0 . (Figure 6) Figure 6 AC Power Indicator NOTE: The Z2 display will be active This icon is displayed when the Z2 is connected to an AC power outlet via the Power Supply . whenever the device is receiving power . -
Page 8: Starting And Stopping Treatment
Stop Button and the indicated pressure will rise as Start/Stop If you prefer to stop the Z2 using the Start / Stop Button, you can disable the Auto Stop Feature. the Z2 ramps up to prescribed treatment pressure . Button... -
Page 9: Programming Ramp Mode
Z2 is not powered) . The Z2 will return to standby mode . To return to standby mode without Z2 . Never attempt to clean the Power Adapter, PowerShell, Battery or saving the new setting, press and release the Start/Stop Button momentarily instead of holding it accessories with any of these solutions . -
Page 10: Usb Firmware Upgrade
Troubleshooting 1 . Clean the exterior of the Z2 with a soft damp cloth and mild detergent and wipe clean . Never submerge the Z2 in water . Do not allow soap or water to enter the Z2 . Problem Possible Causes &... -
Page 11: Guidance And Manufacturer's Declaration
The Z2 CPAP System is intended for use in the electromagnetic environment specified below . The Air Leak is Occurring customer or the user of the Z2 CPAP System should assure that it is used in such an environment . Follow mask manufacturer’s instructions . - Page 12 This device complies with part 15 of the FCC Rules . Operation is subject to the following two fixed RF transmitters, an electromagnetic site survey should be considered . If the measured field strength in the location in which the Z2 CPAP conditions: (1) This device may not cause harmful interference, and (2) this device must accept System is used exceeds the applicable RF compliance level above, the Z2 CPAP System should be observed to verify normal operation .
-
Page 13: Technical Specifications
Not for use with oxygen Standard air filter Polyester Air outlet The 22 mm air outlet complies with ISO 5356-1 Battery charges when Z2 not in use . Performance Specifications Operating pressure range 4 to 20 cm H2O Maximum single fault steady pressure... -
Page 14: Servicing
Breas Medical Service Center if there is any sign of wear or concern with Z2 function . Otherwise, service of the Z2 generally should not be required during the warranty period (see ‘Limited Warranty’ for details) of the device . - Page 15 This page is intentionally left blank. This page is intentionally left blank.
- Page 16 This page is intentionally left blank.
Need help?
Do you have a question about the Z2 and is the answer not in the manual?
Questions and answers