Subscribe to Our Youtube Channel
Related Manuals for SHOWTEC Perfomer Profile 600 LED MKIII V1
Summary of Contents for SHOWTEC Perfomer Profile 600 LED MKIII V1
- Page 1 MANUAL ENGLISH Performer Profile 600 LED MKIII Ordercode: 33065 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Performer Profile 600 LED MKIII Table of contents Warning ....................................3 Safety Instructions ................................. 3 Operating Determinations ............................5 Rigging .................................... 5 Connection with the mains............................6 Return Procedure ................................7 Claims ....................................7 Description of the device ..............................8 Features .................................. - Page 3 Performer Profile 600 LED MKIII Cleaning ....................................26 Cleaning 19°, 26°, 36°, and 50° glass lenses ......................26 Cleaning the reflector..............................26 Maintenance ..................................27 Replacing the Fuse ..............................27 Troubleshooting ................................27 No Light ..................................27 No Response to DMX..............................28 Product Specifications ..............................29 Dimensions ..................................30 Ordercode: 33065...
-
Page 4: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: ● Showtec Performer Profile 600 LED MKIII ● PowerCON to Schuko power cable 1,5 m ●... - Page 5 ● If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 6: Operating Determinations
Performer Profile 600 LED MKIII ● The user is responsible for correct positioning and operating of the Performer. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device. ● This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth. -
Page 7: Connection With The Mains
Performer Profile 600 LED MKIII Connection with the mains Connect the device to the mains with the power-plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER PHASE BLUE BLACK... -
Page 8: Return Procedure
Performer Profile 600 LED MKIII Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture. -
Page 9: Description Of The Device
Performer Profile 600 LED MKIII Description of the device Features The Showtec Performer Profile 600 LED MKIII is a theater spotlight fixture with high output and great effects. ● Extremely quiet ● Accessory slot for motorized pattern devices or optional iris ●... -
Page 10: Overview
Performer Profile 600 LED MKIII Overview Fig. 01 01) Lens tube (not included) 02) Barrel 03) Shutter 04) Body 05) Adjustment handle 06) Mounting bracket 07) Safety Eye Ordercode: 33065... -
Page 11: Backside
Performer Profile 600 LED MKIII Backside Fig. 02 08) LCD display + control buttons 09) Fuse T6,3AL/250V 10) PowerCON power connector 100-240V IN (Blue) 11) PowerCON power connector 100-240V OUT (Grey) 12) 5-pin DMX signal connector IN 13) 5-pin DMX signal connector OUT 14) 3-pin DMX signal connector OUT 15) 3-pin DMX signal connector IN Ordercode: 33065... -
Page 12: Installation
Performer Profile 600 LED MKIII Installation Remove all packing materials from the Performer Profile 600 LED MKIII. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. Always disconnect from electric mains power supply before cleaning or servicing. -
Page 13: Color Frame Retaining Clip
Performer Profile 600 LED MKIII Color frame retaining clip The color frame holder is equipped with a spring-loaded retaining clip. This prevents color frames and accessories from falling out (Fig. 05). Make sure that all color frame accessories are locked in position with the retaining clip before hanging the Performer Profile 600 LED MKII. -
Page 14: Shutters
Performer Profile 600 LED MKIII Shutters The shutters are located inside the barrel. Move them back and forth to modify the shape of the beam. Fig. 06 Drop-in Iris-Slot The Drop-in Iris slot is located on the top of the barrel. It accommodates either a drop-in iris or a motorized pattern device. -
Page 15: Rotating The Barrel Assembly
Performer Profile 600 LED MKIII Rotating the barrel assembly 01) Loosen the barrel rotation control. It can be found directly behind the shutters on the underside of the reflector housing (Fig 08). Do not remove the barrel rotation control. 02) Rotate the barrel to the desired position. 03) Once the barrel is positioned, tighten the barrel’s rotation control to lock it into position. -
Page 16: Setting The Angle
Performer Profile 600 LED MKIII Setting the angle 01) Loosen the adjustment screws. Do not remove the adjustment screws. 02) Tilt the fixture to the desired position (Fig. 10). 03) Tighten the adjustment screws to secure the fixture in position. Fig. -
Page 17: Control Modes
Performer Profile 600 LED MKIII Control Modes There are 3 modes: • Manual control (Dimmer) • Master/Slave • DMX-512 (1CH, 2CH, 3 CH) One Performer (Manual control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). -
Page 18: Multiple Performers (Dmx Control)
Performer Profile 600 LED MKIII Multiple Performers (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the Performers and other devices. 04) Link the units as shown in fig. -
Page 19: Fixture Linking
Performer Profile 600 LED MKIII Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 20: Control Panel
Performer Profile 600 LED MKIII Control Panel A) LCD Display MENU button C) ENTER button D) UP button DOWN button Fig. 13 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address, next time.) DMX Addressing The control panel on the front side of the base allows you to assign DMX fixture addresses, which is the first... -
Page 21: Menu Overview
Performer Profile 600 LED MKIII Menu Overview Ordercode: 33065... -
Page 22: Main Menu Options
Performer Profile 600 LED MKIII Main Menu Options 01) On start-up, the device will display information about the device’s actual temperature, the current software version, run mode, DMX personality and DMX address: 02) Press the ENTER button to open the main menu. 03) Press the UP/DOWN buttons to toggle through the main menu options. -
Page 23: Address
Performer Profile 600 LED MKIII 3. Address In this menu you can set the desired DMX starting address. 01) While in the main menu, press the UP and DOWN buttons until the display shows ADDRESS. 02) Press the ENTER button to open the menu, the display will show: 03) Press the UP/DOWN buttons to set the desired DMX starting address. -
Page 24: Dimmer Speed
Performer Profile 600 LED MKIII 4.2 Dimmer speed 01) When the display shows DIMMER, press the ENTER button to open the menu. 02) Press the UP and DOWN buttons to toggle between the 5 options: Dimmer Speed OFF DIM1- DIM 4 Dimmer speed, from fast to slow 4.3 Dimming curve settings 01) When the display shows CURVE, press the ENTER button to open the menu. -
Page 25: Save Dmx/Blackout
Performer Profile 600 LED MKIII 4.7 Save DMX/Blackout 01) When the display shows DMX ERROR, press the ENTER button to open the menu. 02) Press the UP and DOWN buttons to toggle between the 2 options: SAVE DMX data save BLACK Blackout 03) If the display shows SAVE, the Performer will fall back on the last working DMX signal, which will ensure... -
Page 26: Dmx Channels
Performer Profile 600 LED MKIII DMX Channels 1 Channel (UNO) Channel 1 – Dimmer 0-255 Dimmer intensity, from dark to brightest 0-100% 2 Channels (DOS) Channel 1 – Dimmer 0-255 Dimmer intensity, from dark to brightest 0-100% Channel 2 – Fine dimmer 0-255 Fine dimmer adjustment 3 Channels (STD.P) -
Page 27: Cleaning
Performer Profile 600 LED MKIII Cleaning Please follow the next recommendations when cleaning and inspecting lenses and reflectors: Do not use glass or window type cleaners on lenses (glass or polymer) or reflectors. Do not use abrasive materials such as steel wool. Replace lenses if they contain visible damage (cracks or deep scratches) which that may impair their effectiveness. -
Page 28: Maintenance
Suspect three potential problem areas as: the power supply, the LED, the fuse. 01) Power supply. Check if the unit is plugged into an appropriate power supply. 02) The LED. Return the Performer to your Showtec dealer. 03) The fuse. Replace the fuse. See page 27 for replacing the fuse. -
Page 29: No Response To Dmx
Performer Profile 600 LED MKIII No Response to DMX Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction. 01) Check the DMX setting. Make sure that DMX addresses are correct. 02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power. Try your DMX control again. -
Page 30: Product Specifications
Performer Profile 600 LED MKIII Product Specifications Model: Showtec Performer Profile 600 LED MKIII Input Voltage: 100 - 240V AC, 50/60Hz Power consumption: 250W (full output) DMX linking: 30pcs Fuse: T6,3AL/250V Dimensions: 485 x 305 x 460 mm (LxWxH) Weight:... -
Page 31: Dimensions
Performer Profile 600 LED MKIII Dimensions Ordercode: 33065... - Page 32 ©2018 Showtec...
Need help?
Do you have a question about the Perfomer Profile 600 LED MKIII V1 and is the answer not in the manual?
Questions and answers