Table of Contents
Advertisement
Getting Familiar With the controlCARD
3.3
Assumed Operating Conditions
This kit is assumed to run at standard room conditions. The EVM should run at approximately Standard
Ambient Temperature and Pressure (SATP) with moderate-to-low humidity.
3.4
Using the controlCARD
For the controlCARD to work, the controlCARD MCU must be powered. This is usually done by inputting
5-VDC through the HSEC connector through an accompanying baseboard. For example, if using a
docking station baseboard, 5-VDC should be input into the docking station's J1 or J17, then SW1 must be
toggled to the appropriate position.
Based on the way that the controlCARD is used, additional hardware settings may be necessary, as
shown in
Table
2.
Component
S1:A (controlCARD)
J1:A (controlCARD)
S1 (controlCARD)
Baseboard's JTAG connector
(J2 on the Docking Station
baseboard)
The F280049 controlCARD to docking station signal mapping can be found in the
controlCARD product directory at \ti\c2000\C2000Ware_XXXX\boards\controlCARDs:
•
TMDSCNCD28004x_RevA_120cCARD_pinout.pdf -- F280049 signal mapping on the default HSEC
docking station
•
TMDSCNCD28004x_RevA_100DIM_map.pdf -- F280049 signal mapping on the legacy DIM100
docking station if using TMDSADAP180TO100 adapter card
Hardware support files for the F280049 controlCARD and docking station can also be found in the
C2000Ware product directories:
•
F280049 controlCARD: \ti\c2000\C2000Ware_XXXX\boards\controlCARDs
•
Docking station: \ti\c2000\C2000Ware_XXXX\boards\ExperimenterKits
3.5
Software Development
Code Composer Studio
developing and debugging software for the C2000 series of MCUs. CCS is free to download and use with
the controlCARD. Introductory videos for CCS are available at training.ti.com.
NOTE: For users of TMDXDOCK280049M
TMS320F280049M is a discontinued part number that is not supported on new installations
of CCS. Use the functionally equivalent TMS320F280049C part number when creating a new
target configuration for TMDXDOCK280049M on new installations of CCS.
4
Piccolo F280049 controlCARD Information Guide
Table 2. Getting Started Reference
Debug Using CCS and the
on-card XDS100v2 Emulator
Left (Switch 1): Up (ON)
Connect a mini USB cable
between J1:A and the
computer.
In CCS, use this target
configuration:
F280049 device with an
XDS100v2 emulator.
Left (Switch 2): Down (ON)
Right (Switch 1): Up (OFF)
Putting the C2000 device into
Wait Mode can reduce the risk
of connectivity issues.
—
(CCS) is the recommended integrated development environment (IDE) for
Copyright © 2017–2019, Texas Instruments Incorporated
Debug Using CCS and an
External Emulator Through
the Baseboard
Left (Switch 1): Down (OFF)
—
Left (Switch 2): Down (ON)
Right (Switch 1): Up (OFF)
Putting the C2000 device into
Wait Mode can reduce the risk
of connectivity issues.
Connect an external emulator
and appropriately configure the
CCS target configuration.
SPRUIC4C – July 2017 – Revised January 2019
www.ti.com
Standalone (Boot From
FLASH or Other Boot Mode)
Left (Switch 1): Down (OFF)
—
Set S1 as desired
(See
Table 4
for supported
settings)
—
C2000Ware
Submit Documentation Feedback
Advertisement
Table of Contents
