Table of Contents
Advertisement
Quick Links
Printed Matter No. 9839 1860 01
Publication Date 2020-03-06
Valid from Serial No. F1720001
Valid to Serial No. F2439999
ETV ST81-100-13-SH
(20-100 Nm)
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
ETV ST81-100-13-SH
8433205684
WARNING
Electric angle nutrunner
Product Instructions
Advertisement
Table of Contents
Related Manuals for Atlas Copco ETV ST81-100-13-SH
Summary of Contents for Atlas Copco ETV ST81-100-13-SH
- Page 1 ETV ST81-100-13-SH Printed Matter No. 9839 1860 01 Electric angle nutrunner Publication Date 2020-03-06 Valid from Serial No. F1720001 Product Instructions Valid to Serial No. F2439999 ETV ST81-100-13-SH 8433205684 (20-100 Nm) WARNING Read all safety warnings and instructions Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury.
-
Page 2: Table Of Contents
Operating Instructions.................. 9 Operating.................... 9 Service ........................ 11 Preventing ESD problems ................ 11 Maintenance Instructions................ 11 Service recommendations .............. 11 Overhaul .................... 11 Lubrication Instructions................... 12 Lubricating guide ................. 12 Lubrication ................... 12 Repair Instructions.................. 12 Repair .................... 12 Troubleshooting.................... 13 Power Focus 3000/4000................. 13 © Atlas Copco Industrial Technique AB - 9839 1860 01... - Page 3 If the tool becomes very hot................ 13 Power Focus 600/6000................... 13 Recycling ....................... 14 Environmental Regulations................ 14 © Atlas Copco Industrial Technique AB - 9839 1860 01...
-
Page 4: Product Information
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. © Atlas Copco Industrial Technique AB - 9839 1860 01... -
Page 5: Warranty
■ Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty. ■ To avoid damage or destruction of tool parts, service the tool according to the recommended mainte- nance schedules and follow the correct instructions. -
Page 6: Country Of Origin
(>30mA) and if leakage occurs, the drive is switched off (30ms). Changing, interfering or tampering with the protection system voids all warranty and obligations from Atlas Copco. Trouble-shoot- ing and re-start of the system may only be carried out by an authorized person. Check the function of the EFP on a regular basis by pressing the trip-button. -
Page 7: Installation
POWER FOCUS/drive unit. Any changes made of these values in the POWER FOCUS while the tool is connected will be stored in the tool memory. © Atlas Copco Industrial Technique AB - 9839 1860 01... -
Page 8: Fitting Of The Tool Cable
To clamp the tool to a fixture, only the areas marked grey on the figure can be used. However, be careful not to damage the rubber coating when clamping the rubber handle. NOTICE The white areas in the picture must not be used for fixturing. © Atlas Copco Industrial Technique AB - 9839 1860 01... -
Page 9: Operation
The soft-start function facilitates entering the screw head and thread. The duration of the soft start is adjustable, see the manual for the drive unit. The tool is equipped with signal lights, ■ Green = OK tightening © Atlas Copco Industrial Technique AB - 9839 1860 01... - Page 10 Yellow = Warning – low torque (not for ES) ■ Red = Warning – high torque ■ Orange = Function indicator (only for SL and DL) ■ Blue = Function indicator (only for SL) © Atlas Copco Industrial Technique AB - 9839 1860 01...
-
Page 11: Service
If you decide that the electric motor is defect or in need of service, return the complete motor unit to Atlas Copco Industrial Technique for replacement. Motors which have been opened by anyone else than Atlas Copco Industrial Technique will not be ser- viced. -
Page 12: Lubrication Instructions
Repair Instructions Repair Repair must only be carried out by qualified authorised personnel. For further information contact your lo- cal Atlas Copco sales representative. © Atlas Copco Industrial Technique AB - 9839 1860 01... -
Page 13: Troubleshooting
Is the unit switched on? Check the earth fault circuit breaker behind the front door. Should it have tripped, make sure to find the primary fault before resuming operation. Check that the wiring on the remote start connector is correct. For further information see 9836 4954/9836 7446. © Atlas Copco Industrial Technique AB - 9839 1860 01... - Page 14 When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation. Batteries shall be taken care of by your national battery recovery organization. © Atlas Copco Industrial Technique AB - 9839 1860 01...
- Page 16 Original instructions © Copyright 2020, Atlas Copco Industrial Technique AB. All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. Atlas Copco Industrial This applies in particular to trademarks, model denominations, part numbers Technique AB and drawings.