Sargent and Greenleaf 8077 Manual & Changing Combination Video Instructions

Sargent and Greenleaf 8077 Manual & Changing Combination Video Instructions

Advertisement

Sargent and Greenleaf 8077 Manual & Changing Combination Video Instructions

INTRODUCTION

All new 8077 locks are shipped from the factory set to a single combination number of 25. A new combination should be set before the lock is used.

Before attempting to operate the lock, study the illustrations and familiarize yourself with the names of the various parts of the padlock. Before attempting to change the combination, you should be thoroughly familiar with the opening procedure.

When opening the lock or changing the combination, care should be taken to very precisely align the numbers of the combination and the index. Failure to do this could cause difficulties in opening the lock.

For additional dialing tips, visit S&G's website, at: www.sargentandgreenleaf.com

OPENING PROCEDURE

  1. If the lock is set to the factory shipping combination, use this procedure:
    1. If the lock is new and is just being put into service, its combination is set to the single number 25.
    2. Turn the dial counterclockwise four complete revolutions. On the fourth revolution, align the number 25 on the dial with the padlock's opening index. See Figure A.
      OPENING PROCEDURE
      Figure A
    3. Turn the dial clockwise to align zero with the padlock's opening index.
    4. Pull sharply on the shackle to open the lock.
      warning Note: If the lock fails to open, dial ½ number lower or higher to compensate for possible variation of the factory setting. For instance, you should try dialing to 24½ or 25½.
  2. If the lock is set to a true, three number combination, use this procedure:
    1. Turn the dial left (counterclockwise) until the first number of the combination aligns with the opening index the fourth time.
    2. Turn the dial right (clockwise) until the second number of the combination aligns with the opening index the third time.
    3. Turn the dial left until the third number of the combination aligns with the opening index the second time.
    4. Turn the dial right until zero is aligned with the opening index the first time.
    5. Pull sharply on the shackle to open the lock.


After re-locking the padlock, the dial must be turned at least five complete revolutions in either direction to ensure the mechanism is fully locked.

CHANGING PROCEDURE

  1. Using the existing combination, open the lock as descirbed in the OPENING PROCEDURE.
  2. Use the screwdriver end of the change key (Figure B) to turn the cover locking screw (Figure C) clockwise until it comes to a complete stop.
  3. Remove the padlock's rear cover plate by sliding it upward.
  4. Turn the padlock's cover locking screw counterclockwise, backing it out of the lock body as far as possible. It does not have a positive stop.
  5. Close the shackle.
  6. Cover the opening index mark with a small piece of tape or your thumb to prevent the possibility of dialing the numbers to the opening index.
  7. Dial the existing combination to the changing index. All numbers of the combination, including the last turn to zero, are used in the combination changing procedure.
    1. If the lock is new and just being put into service, the single number 25 is the combination. Turn the dial left (counterclockwise) until 25 aligns with the changing index the fourth time. Turn the dial right (clockwise) one-half revolution, stopping when zero is aligned with the changing index the first time.
      Do not pull on the shackle.
    2. If the lock is set on any other combination, use the same procedure given for opening the lock, but dial the numbers to the changing index.
  8. Use the elbow of the change key (Figure B)
    Use the elbow of the change key
    Figure B

    to turn the key hole screw on the back of the lock (Figure C) clockwise to the open position.
    Turn the key hole screw on the back of the lock
    Figure C

    If it will not turn, repeat the procedure in step 7.
  9. Insert the change key (tip first) into the change key hole in the back of the lock. The change key is properly seated when the tab on the key is fully inside the lock. Turn the key clockwise one-quarter turn.
  10. Set the new combination as follows:
    1. Turn the dial left until the first number of the new combinaiton aligns with the changing index the fourth time.
    2. Turn the dial right until the second number of the new combination aligns with the changing index the third time.
    3. Turn the dial left until the third number of the new combination aligns with the changing index the second time.
    4. Turn the dial clockwise until zero aligns with the changing index the first time.
  11. Once the new combination is set and zero is aligned with the changing index, turn the change key counterclockwise one-quarter turn and remove. Do not turn the key hole screw at this time.
    warning Note: To ensure you have correctly set the combination, you should once again completely re-dial the new combination as directed in Step 10. Re-insert the change key fully into the lock, but do not turn it. If the key will fully insert, you have set the new combination correctly.
  12. Remove the change key and again dial the new combination (including the final turn to zero) to the changing index. Using the change key elbow, turn the key hole screw to the closed position, and close the shackle.
  13. If the key hole screw will not return to the closed position, the combination has been incorrectly dialed. Re-dial the combinaiton to the changing index and try again.
  14. Remove the tape or your thumb from the opening index. Dial the new combination to the opening index following the steps in the OPENING PROCEDURE, and pull sharply on the schackle to open the lock.
  15. Turn the cover locking screw clockwise until it comes to a complete stop.
  16. Slide the rear cover into place.
  17. Turn the lock's cover locking screw counterclockwise as far as possible. Close the shackle.
  18. After any combination change, it is advisable to operate the lock at least three times before putting it into service.

Videos

Sargent and Greenleaf combo padlock 8077 - changing the combination Video

How to change combination on Sargent & Greenleaf 8077 Padlock - Video

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Sargent and Greenleaf 8077 Manual & Changing Combination Video Instructions

Advertisement

Need help?

Need help?

Do you have a question about the 8077 and is the answer not in the manual?

Questions and answers

Table of Contents