09 Recommended Cutting Speeds With Shielded Tip - ESAB CUTMASTER 60i Operating Manual

ESAB CUTMASTER 60i
4T.09 Recommended Cutting Speeds With Shielded Tip
CutMaster® 60i With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Output Amperage
Inches mm (Cat. Volts
No.) (VDC)
0.036 0.9 9-8208 114
0.06 1.5 9-8208 120
0.075 1.9 9-8208 121
0.135 3.4 9-8208 122
0.188 4.8 9-8208 123
0.25 6.4 9-8208 125
0.375 9.5 9-8208 138
0.500 12.7 9-8208 142
0.625 15.9 9-8208 152
CutMaster® 60i With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Output Amperage
Inches mm (Cat. Volts
No.) (VDC)
0.036 0.9 9-8208 109
0.05 1.3 9-8208 105
0.06 1.5 9-8208 115
0.078 2.0 9-8208 120
0.135 3.4 9-8208 125
0.188 4.8 9-8208 132
0.25 6.4 9-8208 130
0.375 9.5 9-8208 130
CutMaster® 60i With Shielded Tip
Type Plasma Gas: Air
Thickness Tip Output
Inches mm (Cat. Volts
No.) (VDC)
0.032 0.8 9-8208 116
0.051 1.3 9-8208 116
0.064 1.6 9-8208 118
0.079 2.0 9-8208 116
0.125 3.2 9-8208 130
0.188 4.8 9-8208 132
0.250 6.4 9-8208 134
0.375 9.5 9-8208 143
4T-12
Speed (Per
Minute)
(Amps) Inches Meters Inches
40 170 4.32 0.19
40 90 2.29 0.19
40 80 2.03 0.19
40 75 1.91 0.19
40 30 0.76 0.19
40 25 0.64 0.19
40 11 0.28 0.19
40 7 0.18 0.19
40 3 0.08 0.19
Speed (Per
Minute)
(Amps) Inches Meters Inches
40 180 4.57 0.125
40 165 4.19 0.125
40 120 3.05 0.125
40 65 1.65 0.187
40 25 0.64 0.187
40 20 0.51 0.187
40 15 0.38 0.187
40 10 0.25 0.187
Amperage Speed (Per
Minute)
(Amps) Inches Meters
40 220 5.59
40 210 5.33
40 180 4.57
40 150 3.81
40 75 1.91
40 60 1.52
40 28 0.71
40 11 0.28
OPERATION
Type Material: Mild Steel
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas
Pressure*
mm psi bar Plasma
4.8
4.8
Set to the
4.8
central
region on
4.8
the pressure
4.8
dial. This is
4.8
illuminated
green when
4.8
selected.
4.8
4.8
Type Material: Stainless Steel
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas
Pressure*
mm psi bar Plasma
3.2
Set to the
3.2
central
3.2
region on
4.8
the pressure
dial. This is
4.8
illuminated
4.8
green when
4.8
selected.
4.8
Type Material: Aluminum
Type Secondary Gas: Single Gas Torch
Standoff Plasma Gas
Pressure*
Inches mm psi bar Plasma
0.187 4.8 Set to the
central
0.187 4.8
region on
0.187 4.8
the pressure
0.19 4.8 dial. This is
illuminated
0.19 4.8
green when
0.187 4.8
selected.
0.187 4.8
0.187 4.8
Flow (SCFH) Pierce Pierce
Height
Total** Delay Inches
(Sec)
55 170 0.00 0.2
55 170 0.10 0.2
55 170 0.30 0.2
55 170 0.40 0.2
55 170 0.60 0.2
55 170 1.00 0.2
55 170 NR NR
55 170 NR NR
55 170 NR NR
Flow (SCFH) Pierce Pierce
Height
Total** Delay Inches
(Sec)
55 170 0.00 0.2
55 170 0.00 0.2
55 170 0.10 0.2
55 170 0.30 0.2
55 170 0.40 0.2
55 170 0.60 0.2
55 170 1.00 0.2
55 170 NR NR
Flow (SCFH) Pierce Pierce
Height
Total** Delay Inches
(Sec)
55 170 0.00 0.2
55 170 0.00 0.2
55 170 0.10 0.2
55 170 0.30 0.2
55 170 0.40 0.2
55 170 0.60 0.2
55 170 1.00 0.2
55 170 NR NR
Manual 0-5488
mm
5.1
5.1
5.1
5.1
5.1
5.1
NR
NR
NR
mm
5.1
5.1
5.1
5.1
5.1
5.1
5.1
NR
mm
5.1
5.1
5.1
5.1
5.1
5.1
5.1
NR