Husqvarna AUTOMOWER 420 Operator's Manual page 28
Hide thumbs
Also See for AUTOMOWER 420:
- Technical manual (104 pages) ,
- Operator's manual (100 pages) ,
- Workshop manual (60 pages)
Table of Contents
Advertisement
6.
Use the arrow buttons and the OK button to
move through the menu structure
Coverage > Area 1-5 > More > Test .
7.
Push the OK button.
8.
Push the STOP button when the product is at
the distance you select to measure. The distance
shows in the display.
To disable or enable the Lawn Coverage function
Lawn Coverage function for each
Disable or enable the
area.
To get access to the menu in the
1.
Do steps 1–3 in
display of the product on page 23 .
2.
Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-5 > Disable .
3.
Push the OK button.
4.
Push the BACK button.
To reset the Lawn Coverage settings
Lawn Coverage settings for each area
You can reset the
and use the factory setting.
1.
Do steps 1–3 in
To get access to the menu in the
display of the product on page 23 .
2.
Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-5 > More > Reset .
3.
Push the OK button.
4.2.8.2 Methods for the product to find the charging
station
The product has 3 search methods to find the charging
station:
•
Irregular - The product operates in the work area
until it finds the signal of the charging station.
•
Guide wire - The product operates in the work area
until it finds the signal of the charging station or
the guide wire. If it finds the guide wire the product
moves along the guide wire to the charging station.
•
Boundary wire - The product moves in the work
area until it finds the signal of the charging station,
the guide wire or the boundary wire. If it finds
the boundary wire, the product moves along the
boundary wire to the charging station.
The factory setting is set to mix the 3 search methods.
When the battery is low the product starts to search for
the charging station with the irregular method for 3 min.
After 3 min the product changes search method to the
guide wire method. After 11 min the product changes
search method to the boundary wire method.
You can change the settings for how the product finds
the charging station to adapt to the work area.
To set how the product finds the charging station
You can make manual settings to make the product
search for the guide wire or the boundary wire in 0–30
min from when the battery is low.
28 - Product settings
Settings > Lawn
Installation > Lawn
Installation > Lawn
To get access to the menu in the
1.
Do steps 1–3 in
display of the product on page 23 .
2.
Use the arrow buttons and the OK button to move
through the menu structure
the charging station > Overview of search methods
> Guide .
3.
Push the arrow buttons to select 1 of the guide
wires.
4.
Push the number buttons to set the time.
5.
Push the OK button.
6.
Push the BACK button.
7.
Use the arrow buttons and the OK button to move
through the menu structure
the charging station > Overview of search methods
> Boundary wire .
8.
Push the number buttons to set the time.
9.
Push the OK button.
10. Push the START button and close the hatch.
To do a test of the guide wire
To get access to the menu in the
1.
Do steps 1–3 in
display of the product on page 23 .
2.
Use the arrow buttons and the OK button to move
through the menu structure
charging station > Guide > More > Test guide .
3.
Put the product 3 m / 9 ft. from the guide wire,
facing the guide wire.
4.
Push the START button and close the hatch.
5.
Make sure the product follows the guide wire to the
charging station.
6.
Make sure the product docks with the charging
station.
7.
If the product does not dock with the charging
station, change the position of the charging station
or the guide wire. Refer to
station on page 19 and To install the guide wire on
page 20 .
To do a test of the boundary wire
1.
Put the product 3 m / 9 ft. from the boundary wire,
facing the boundary wire.
To get access to the menu in the
2.
Do steps 1–3 in
display of the product on page 23 .
3.
Use the arrow buttons and the OK button to move
through the menu structure
charging station > Overview of search methods >
Boundary > More > Test right / Test left .
4.
Push the START button and close the hatch.
5.
Make sure the product follows the boundary wire to
the charging station.
6.
Make sure the product docks with the charging
station.
7.
Change the position of the charging station or the
boundary wire if the product does not dock with the
Installation > To find
Installation > To find
Installation > Find
To install the charging
Installation > Find
1201 - 007 - 20.02.2023
Advertisement
Table of Contents
