Husqvarna AUTOMOWER 420 Operator's Manual page 27
Hide thumbs
Also See for AUTOMOWER 420:
- Technical manual (104 pages) ,
- Operator's manual (100 pages) ,
- Workshop manual (60 pages)
Table of Contents
Advertisement
In the Installation menu it is possible to adapt the
settings of the product for best mowing result.
4.2.8.1 Lawn Coverage
If the work area includes remote parts that are
connected with narrow passages, the
function is useful to be able to maintain a well-cut lawn
in all parts of the yard. A guide wire must be installed to
use the functions. You can set a maximum of 5 remote
areas.
Lawn Coverage function the product first
With the
follows and then leaves the guide wire after a certain
distance and starts to mow the lawn.
Area A, approximately 50%
Area B, approximately 30%
Area C, approximately 20%
A
GPS Assisted Navigation
®
Only for Automower
430X/450X.
The GPS Assisted Navigation function helps the product
to select the most optimal operation. Use the Lawn
coverage function to do manual settings.
To set the GPS Assisted Navigation
Disable the GPS Assisted Navigation to make manual
Lawn coverage .
settings in
Note:
It is recommended to use GPS Assisted
Navigation.
To get access to the menu in the
1.
Do steps 1–3 in
display of the product on page 23 .
2.
Use the arrow buttons and the OK button to move
through the menu structure
coverage .
3.
Push the OK button to enble or disable the
function.
4.
Push the BACK button.
1201 - 007 - 20.02.2023
Lawn Coverage
C
B
Installation > Lawn
To set the Lawn Coverage function
To get access to the menu in the
1.
Do steps 1–3 in
display of the product on page 23 .
2.
Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-5 .
3.
Use the arrow button to select the area.
4.
Push the OK button.
5.
Measure the distance from the charging station
to the start of the area. Measure along the guide
To measure the distance from the
wire. Refer to
charging station on page 27 .
6.
Push the number buttons to select the distance.
7.
Push the OK button.
8.
Use the number buttons to select the percentage
of the cutting time the product must cut the area.
The percentage is equal to the area in relation to
the complete work area.
a)
Measure the area.
b)
Divide the measured area with the total work
area.
c)
Convert the result to percentage.
Note:
The sum of Area 1-5 must be 100% or
less. If the sum is less than 100%, the product
sometimes starts to mow at the charging station.
To set the exit angle on page 29 .
Refer to
9.
Push the BACK button.
To do a test of the Lawn Coverage function
1.
Put the product in the charging station.
To get access to the menu in the
2.
Do step 1-3 in
display of the product on page 23 .
3.
Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-5 > More > Test .
4.
Push the OK button.
5.
Push the START button.
6.
Close the hatch.
7.
Make sure the product can find the area.
To measure the distance from the charging station
1.
Put the product in the charging station.
To get access to the menu in the
2.
Do steps 1–3 in
display of the product on page 23 .
3.
Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-5 > How far?
4.
Use the number buttons to set 500 m / 500 yd as a
distance.
5.
Push the OK button.
Installation > Lawn
Installation > Lawn
Installation > Lawn
Product settings - 27
Advertisement
Table of Contents
