This category contains useful tips for handling the product efficiently. Failure to observe these tips will not result in damage to the product. This information does not include any information relevant to health or workplace safety. Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
► Observe the specified maintenance intervals and specifications regarding the quality of the operating material. ► When using the product under extreme conditions, adjust the maintenance interval according to the degree of contamination. Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
Installation, commissioning and maintenance may only be performed by trained specialists. These persons must have read and understood the installation and operating instructions in full. Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
The products are designed for holding, transporting and positioning workpieces. SB series products enable a swivel angle of 90° or 180°, which are set using the end stops. SBZ series products enable a swivel angle of 90° or 180° depending on the product variant.
The products differ in the mechanics of how force is transmitted and in how the drive works. The SB series is driven by a double-acting pneumatic rotary cylinder. The force is transmitted to the output shaft by a toothed belt.
8 Accessories/scope of delivery INFORMATION If any accessories not sold or authorized by Zimmer GmbH are used, the function of the product cannot be guaranteed. Zimmer GmbH accessories are specifically tailored to the individual products. ► For optional accessories and those included in the scope of delivery, refer to our website.
► Observe the tightening torque of the mounting screws. ► Verify the permitted load capacity of the required screw connections in accordance with VDI 2230. Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
► Mount the product using the straight pins and mounting screws. Gripper Connection plate Swivel jaw Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
Page 12
► You can find more information in the technical data sheet on our website. SBZ series SB series Mounting screw Straight pins Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
Threaded holes and holes for straight pins are provided on the flange of the output shaft for the installation of workpiece-specific applications. SBZ series SB series Hole for mounting screw Hole for straight pin Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
► You can find information on available pneumatic connections on our website. ► Please contact Zimmer Customer Service if you have any questions. Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
► Retighten the lock nut. ► Repeat the process for the other side. Stop screw End stop 90° End stop 180° Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
11.3 Sensing positions for the SB series NOTICE The cables that are used by Zimmer GmbH feature a minimum bending radius of 10 x the outer diameter. This bending radius must not be undershot! ► Freely suspended cables must be secured to prevent excessive motion loads or pinching.
11.4 Sensing positions for the SBZ series NOTICE The cables that are used by Zimmer GmbH feature a minimum bending radius of 10 x the outer diameter. This bending radius must not be undershot! ► Freely suspended cables must be secured to prevent excessive motion loads or pinching.
• After approximately 30 cycles in the cycle time that is selected later, the shock absorber reaches operating temperature. • If a break time of > 1 minute is exceeded, no shock absorber warm-up is required. Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
Page 20
► If necessary, readjust the adjustment screws and shock absorbers. ► Tighten the lock nut. Flow control valve Shock absorber Lock nut Adjustment screw Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
► Dispose of the components properly according to the material groups. ► Comply with the locally applicable environmental and disposal regulations. Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...
Authorized representative for the (Place and date of issuance) Martin Zimmer compilation of relevant technical (Legally binding signature) documents Managing Partner Zimmer GmbH • Im Salmenkopf 5 • 77866 Rheinau, Germany • +49 7844 9138 0 • www.zimmer-group.com...