Advertisement
1 set for VM341
2 sets for VM341-2
The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time. With the battery alone, the parent unit can cordlessly run for a short time only.
NOTES
Install the battery as shown below.
NOTE
NOTE
To replace the battery, press down on the large tab of the battery compartment cover and pull it out, then follow the steps above to install the battery.
NOTES
When you have connected the parent unit and installed its battery for the first time or after power outage, the parent unit powers on automatically. The battery icon indicates the battery status (see the following table).
NOTES
Battery indicators | Battery status | Action |
The battery icon is off and displays. | No battery is installed but operates using AC power, or the battery has been installed incorrectly. | Install the parent unit battery. Charge without interruption (at least 30 minutes). |
The screen displays Battery low at Parent Unit and . The light flashes. | The battery has very little charge and may be used for only a short time. | Charge without interruption (about 30 minutes). |
The battery icon becomes solid . | The battery is fully charged. | To keep the battery charged, connect it to AC power when not in use. |
NOTE
You may test the baby monitor before initial use, and at regular times thereafter.
NOTE
TIP
NOTE
The operating range of the baby monitor is up to 300 meters (1,000 feet) outdoors or 50 meters (160 feet) indoors. The actual operating range may vary depending on the environmental conditions and other interferences such as walls, doors and other obstructions.
1 | Light sensor |
2 | Camera |
3 | Infrared LEDs |
4 | Play/Stop
|
5 | ON/OFF light
|
6 | Microphone |
7 | Skip
|
8 | +/VOL/-
|
9 | ON/OFF switch
|
10 | Temperature sensor |
11 | Speaker |
12 | Threaded socket
|
13 | PAIR
|
14 | Power jack |
1 | Antenna |
2 | LED lights
|
3 | Microphone |
4 | On/off
|
5 | TALK
|
6 | Zoom
|
7 |
|
8 | BACK
|
9 | VIEW / LCD ON/OFF
PATROL
SPLIT
|
10 | +/VOL
|
11 | -/VOL
|
12 | MENU/SELECT
|
13 |
|
14 |
|
15 | Stand |
16 | Speaker |
17 | Power jack |
LINK | On when the parent unit is linked to the baby unit. Flashes when the link to the baby unit being viewed in SINGLE-CAM or PATROL mode is lost; or when the link to all baby units being viewed in SPLIT-VIEW mode is lost. |
On when the parent unit is connected to AC power, or the battery is charging. Flashes when the parent unit battery is low and needs charging. Off when the parent unit is disconnected from AC power. | |
TALK | On when the parent unit is talking to the baby unit. |
On when the speaker volume of the parent unit is turned off. |
Connection status
| |
Lullaby
| |
Current view status
SINGLE-CAM and PATROL mode.
| |
Patrol mode
| |
Split-view mode
| |
Night vision
| |
Zoom
| |
Temperature alert tone
| |
oF or oC | Real-time temperature
|
Mute alert • Displays when the parent unit speaker volume is set to off. • Displays when SPLIT-VIEW mode is turned on. | |
9-level sound indicator
| |
Speaker volume
| |
Battery status
| |
AC power without battery
|
Language You can select a language (English, French or Spanish) to be used in all screen displays. | |
Alert Tone You can set the parent unit to beep when
| |
Sensitivity With this feature, you can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. | |
Temperature You can turn on the Temperature alert tone so that the parent unit beeps whenever the room temperature detected by the baby unit falls outside of the desired temperature range. | |
Vibration You can turn on the vibration alert so that the parent unit vibrates when it receives Low battery tone, No link alert, Sound alert in split-view or Temperature alert tone after turning on the respective alert tones. | |
Sound-activated Screen Automatically turns on the parent unit screen when a baby unit detects a sound after the screen is turned off. When no sound is detected, the screen is automatically off to save power. | |
LCD You can change the brightness of the parent unit screen, or turn on the Dim Mode to save power. | |
Rename You can choose a specific name for the baby unit from a pre-defined name list. | |
Pair/Unpair The baby unit and parent unit provided are already paired. You can add or replace baby units (VM304, purchased separately) to your baby monitor system. |
No link to CAM # * | The selected baby unit is out of range or is turned off. |
Battery low at Parent Unit | The battery level of the parent unit is very low and needs to be recharged. |
Battery empty. Powering off... | The battery is empty and needs to be recharged. |
Sound detected at CAM # | The sound level exceeds the threshold at CAM # in SPLIT-VIEW mode. |
Temperature too high at CAM # or Temperature too low at CAM # | The temperature detected by the baby unit is higher/lower than the desired temperature alert range. |
Powering on... | The parent unit is turning on. |
The parent unit is searching for baby units. |
* # represents the selected baby unit number.
You can turn on or off the parent unit screen without powering off the parent unit. You can still hear sound from the baby units.
For parent unit:
NOTE
For baby unit:
The baby unit speaker volume determines the lullaby volume and talkback volume transmitted from parent unit.
You can play lullaby on the baby unit to comfort your baby.
TIPS
You can select a language (English, French or Spanish) to be used in all screen displays.
You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD brightness is preset to Level 3.
The dim mode is preset to on to help you save the parent unit power. Whenever the parent unit has been left idle for 10 minutes while the screen is still on, the screen will be dimmed automatically to save power.
NOTE
You can choose to hear sounds from the baby units all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby units from Lowest to Highest.
The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The sound sensitivity level is preset to Highest.
Sound sensitivity table for reference
Sensitivity Level | Description |
Highest | The parent unit speaker is constantly on, and you will hear all sounds (including background noises) from your baby's room. |
High | The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly. |
Medium | The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds. |
Low | The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds. |
Lowest | The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds. |
TIP
When sound activation is on, as long as no sound is detected within 50 seconds, the parent unit screen will turn off automatically to save power.
When your baby unit detects a sound, the sound activation triggers the parent unit screen to turn on automatically. When no sound is detected within 50 seconds, the screen will be off again.
NOTES
Every time the parent unit is turned on, it displays a baby unit in SINGLE-CAM mode. If there are more than one baby units in your system, you can also monitor your baby in PATROL or SPLIT-VIEW mode.
SINGLE-CAM | The screen displays a single baby unit in full screen. |
PATROL | A single cam view that transits to a different baby unit every 10 seconds. |
SPLIT-VIEW | The screen displays all baby units (up to four) on one screen. |
In SINGLE-CAM or PATROL mode:
In SPLIT-VIEW mode:
NOTE
You can zoom in or out while viewing image from baby unit in SINGLE-CAM and PATROL mode.
You can use the TALK function of the parent unit to comfort your baby in SINGLE-CAM and PATROL mode.
You can set the parent unit to beep when the parent unit operates in low battery condition.
You can set the parent unit to beep when the link between the parent unit and the baby unit is lost.
You can turn on the sound alert feature so that, while in SPLIT-VIEW mode, the parent unit beeps and displays Sound detected at CAM # whenever the baby unit detects sounds.
NOTE
Your baby unit monitors the temperature of your baby's room with its built-in temperature sensor. If the detected temperature is outside of the preset temperature range, the parent unit will display alert message.
You can set the desired room temperature alert range. The minimum temperature can be set between 52 oF (11 oC) and 69 oF (20 oC).
The maximum temperature can be set between 70 oF (21 oC) and 86 oF (30 oC).
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the detected temperature is out of range.
You can choose to display the temperature in Fahrenheit (oF) or Celcius (oC).
You can turn on the vibration feature so that the parent unit vibrates when it receives any of Low battery tone, No link alert, Sound alert in split-view or Temperature alert tone after turning on the respective alert tones.
You can rename each baby unit. Once the baby unit is renamed, its new name together with the baby unit number will appear in the sub-menu of below options:
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from this baby unit is in black and white, and appears on screen.
NOTES
TIP
The baby units and parent unit provided are already paired. You can add or replace any baby units (VM304, purchased separately) to your video and audio monitor system. You can pair a maximum of four baby units to your parent unit.
For more details, refer to the user's manual that comes with your VM304 new baby unit.
To keep this product working well and looking good, follow these guidelines:
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.
Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question, visit our website at www.vtechphones.com, or contact 1 (800) 595-9511 for customer service.
Why does the baby monitor not respond normally? | Try the following (in the order listed) for common cure:
|
Why don't the power-on light of the baby unit and parent unit go on when I switch on the units? | Perhaps the parent unit is not connected to the mains. Insert the appliance plug into the parent unit and put the adapter in a wall socket. Then press and hold to switch on the parent unit and to establish connection with the baby unit. |
Perhaps the baby unit is not connected to the mains. Connect the baby unit to the mains. Then set the ON/OFF switch to ON to switch on the baby unit and to establish connection with the parent unit. | |
Why doesn't my parent unit charge while connected to AC power? | Make sure the power is not controlled by a wall switch. |
Make sure the battery is correctly installed in your parent unit. | |
You may have used the battery for a long time. Replace a new battery. | |
Why is my screen in black and white? | The screen is in black and white during nighttime or in a dark room. This is normal due to external light sources. |
Why do I get glare or blurry display on my screen when viewing my baby at night? | During nighttime or in a dark room, the surroundings and other interfering factors, like lightings, objects, colors and backgrounds may affect the image quality on your parent unit screen. Adjust the baby unit's angle or place the baby unit at a higher level to prevent glare and blurry display. |
Why does the baby monitor produce a high-pitched noise? | The parent unit and baby units may be too close to each other.
|
The ON/OFF light on the baby unit flashes and the parent unit displays . | The baby unit is unpaired from the parent unit. Follow below steps to pair the baby unit. Make sure both parent unit and baby unit are on before pairing.
When pairing is successful, the screen displays the view of newly paired baby unit in SINGLE-CAM mode. The LED light on the new baby unit remains on.
|
Why does the parent unit beep? | The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). |
If the parent unit is powered by the provided battery, it may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for up to 3 hours. | |
If your parent unit is in SPLIT-VIEW mode, some of your baby units may detect sounds. | |
The temperature of your baby's room may be too high or too low. | |
Why does the parent unit beep/vibrate frequently in SPLIT-VIEW mode? | You may have set the sound sensitivity level to Highest when the sound alert (and vibration) feature are turned on. The parent unit notifies you of all sounds including background noise with beeps (or vibrations). Adjust the sound sensitivity to a lower level. |
Why does the parent unit react too quickly to other sounds? | The baby unit also picks up other sounds than those of your baby. Adjust the sensitivity level to a lower level or lower the parent unit speaker volume. |
Why don't I hear a sound/ Why can't I hear my baby cry? | The parent unit speaker volume may be too low or off. Press +/VOL to increase the volume. |
You may have set a low sound sensitivity level. See Adjust the sound sensitivity of the baby unit to set to a higher level. | |
Why can't I establish a connection? Why is the connection lost every now and then? Why are there sound interruptions? | The baby units may be out of range. Move the parent unit closer to the baby units (observe the minimum distance of 1 meter/ 3 feet). |
Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible. |
Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download VTech VM341, VM341-2 - Safe & Sound Full Color Video Monitor Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the VM341 that isn't answered in the manual? Leave your question here.