Subscribe to Our Youtube Channel
Related Manuals for Winco 25PTOS-3
Summary of Contents for Winco 25PTOS-3
- Page 1 25PTOS-3 GENERATOR INSTALLATION AND OPERATORS MANUAL WINCO INC. 225 S. CORDOVA AVE. LE CENTER, MN 56057 507-357-6821 SERVICE DEPT. 507-357-6831 www.wincogen.com...
-
Page 2: Table Of Contents
Should you experience a problem please follow the “Troubleshooting FOUNDATION MOUNTING Tables” near the end of this manual. The warranty listed in the manual TRAILER MOUNTING describes what you can expect from WINCO should you need service THREE-POINT HITCH KIT assistance in the future. ELECTRICAL CONNECTIONS... -
Page 3: Specifications
SPECIFICATIONS F. Be sure the unit is properly grounded to an external ground rod driven into the earth. 25PTOS 2. FIRE HAZARD - Watts 25,000 A. Keep a fire extinguisher nearby and know its proper use. Fire Amps extinguishers rated ABC by NFPA are appropriate. Input Speed 540 RPM Generator Speed 3600 RPM 3. -
Page 4: Testing Policy
C. For s hitch let WINCO take care of the freight claim. If you sign for the unit, the transfer of the ownership requires that you file the freight claim Mount the generator on a trailer if you plan to use it as a portable power source. -
Page 5: Electrical Connections
If you require different inserts or contacts for local code, ELECTRICAL CONNECTIONS CABLE WINCO has a variety of different inserts and contacts avail- Unpack the generator as follows: able. Contact the factory at 507-357-6831 for pricing. generator on A #4 Neoprene/THHN wire size is recommended. - Page 6 WARNING: EQUIPMENT DAMAGE To complete the assembly of the disconnect plug refer to the instruction sheet in the plug kit. Never use acid core solder. When soldering insure no excess solder runs down on the contact surface - Solder on the contact surface will WARNING: ELECTRICAL SHOCK not allow the contacts to mate properly causing them to burn up.
-
Page 7: Operation
OPERATION A. Correct mounting B. Physical damage C. Debris in cooling vents and screens (could cause generator to Output power available and load determination overheat) Before using the generator, read and understand the following IMPORTANT: The manufacturer recommends that, if the generator information. -
Page 8: Generator Procedures
4. Couple the tractor to the generator with the drive shaft (tumbling WARNING: PERSONAL INJURY bar). Couple the tumbling bar to the generator input shaft first, then to Never try to manually stop the generator. Always let it coast until it the power take-off shaft. Check alignment, tractor, power take-off shaft stops. (tumbling bar), and the generator input shaft should form a straight (or nearly straight) line, with less than 15 degrees misalignment between 4. -
Page 9: Lubrication
LUBRICATION 5. Replace the oil level check plug. 6. Replace the breather. The generator bearings are factory lubricated and sealed, and require no further lubrication. CLEANING & INSPECTION The generator input shaft should be cleaned and lubricated with a thin film of grease before installing the drive shaft and each time it is Use a vacuum cleaner or dry low pressure compressed air (regulated removed. -
Page 10: Electrical Testing
to check and if necessary, polish the ring surfaces with a crocus cloth 3. Open test. Set meter to read low resistance ( R x ohms). Holding to maintain the smooth finish. one meter lead on the surface of slip ring No. 1, touch other meter to lead to the surface of slip ring No. -
Page 11: Condenser Testing
CONDENSER TESTING Other wise, restart the generator without the capacitor connected to recheck the generator output. If the generator then provides power, the condenser was at fault and should be replaced. If the generator does Condensers are built into the generator circuit to minimize radio not provide power, the problem was not caused by that condenser, interference during operation. -
Page 12: 36 Month Limited Warranty
36 MONTH LIMITED WARRANTY WINCO, Inc., warrants for thirty-six months from date of shipment, that it will repair or replace at its option, for the original user, the whole or any part of the product found upon examination, by WINCO at its factory at 225 South Cordova Avenue, Le Center, Minnesota, or by any factory-authorized service station, to be defective in material or workmanship under normal standby use (average less than 50 hours per month) and service.
Need help?
Do you have a question about the 25PTOS-3 and is the answer not in the manual?
Questions and answers