Related Manuals for Inficon E-Check
Summary of Contents for Inficon E-Check
- Page 1 Translation of the original operating instructions E-Check Calibration leak for ELT3000 Catalog No. 600-105 From software version lime10en1-05-(2007)
- Page 2 INFICON GmbH Bonner Strasse 498 50968 Cologne, Germany...
-
Page 3: Table Of Contents
INFICON Table of contents Table of contents 1 General information .................... 4 1.1 Warnings..................... 5 2 Safety ......................... 6 2.1 Owner requirements ................... 8 2.2 Duties of the operator ................ 10 2.3 Intended use ..................... 11 3 Scope of delivery, transport, storage.............. 12 4 Description...................... 15 4.1 Markings on the calibrated leak .............. 18... -
Page 4: General Information
1 | General information INFICON 1 General information The E-Check (DMC), only described as a calibration leak below, may only be used in proper condition and in the condition described in the operating instructions and only by trained personnel. ► Observe local regulations for the use of the calibration leak. -
Page 5: Warnings
INFICON General information | 1 1.1 Warnings DANGER Imminent hazard resulting in death or serious injuries WARNING Hazardous situation resulting in potential death or serious injuries CAUTION Hazardous situation resulting in minor injuries NOTICE Hazardous situation resulting in damage to property... -
Page 6: Safety
2 | Safety INFICON 2 Safety DANGER Risk of injury from explosion ► If liquids leak out, dispose of the calibration leak properly. ► Do not smoke and stay away from ignition sources. WARNING Risk of injury from flammable solvents The solvent in the calibration leak is highly flammable. - Page 7 INFICON Safety | 2 NOTICE Property damage from falling Place the calibration leak safely on a flat surface and protect it from falling. ► Remove the transport lock and store the calibration leak for at least 24 hours before use.
-
Page 8: Owner Requirements
2 | Safety INFICON 2.1 Owner requirements The following notes are for companies or any person who is responsible for the safety and effective use of the product by the user, employees or third parties. Safety-conscious operation • Only operate the calibration leak if it is in a technically perfect condition and shows no signs of damage such as escaping solvents. - Page 9 INFICON Safety | 2 Personnel qualifications • Only instructed personnel are to be permitted to work with the calibration leak on the battery leak detector. The instructed personnel must have received training on calibration leaks. • Make sure that authorized personnel have read and understood the instruction manual and all other applicable documents.
-
Page 10: Duties Of The Operator
2 | Safety INFICON 2.2 Duties of the operator • Read, observe, and follow the information in this manual and in the work instructions provided by the owner. This concerns in particular the safety and warning instructions. • Always observe the complete operating instructions for all work. -
Page 11: Intended Use
INFICON Safety | 2 2.3 Intended use The calibration leak is used to calibrate the battery leak detector. This usually takes place once a day. The transport lock (sight glass) is removed for initial useDescription [} 15]. After that, the functional duration is about 12 months. -
Page 12: Scope Of Delivery, Transport, Storage
3 | Scope of delivery, transport, storage INFICON 3 Scope of delivery, transport, storage Scope of delivery Item Quantity Calibration leak Calibrated Leak Certificate Safety data sheet Transport WARNING Risk of explosion due to leaked solvent A sight glass was attached to the diaphragm opening for transport. - Page 13 INFICON Scope of delivery, transport, storage | 3 1 There is no liquid in the 2 There is liquid in the sight glass sight glass For transport the calibrated leak is in a foil package. This foil package contains a fleece which can absorb liquids in case of a leak.
- Page 14 3 | Scope of delivery, transport, storage INFICON Storage WARNING Danger when exceeding the expiration date The calibrated leak may become leaky at the end of its service life because the bonds are attacked by the solvent. Solvents may leak and there is a risk of fire and explosion.
-
Page 15: Description
If the calibrated leak is used to calibrate devices with internal ignition sources (e.g. valves, electric motors, Pirani vacuum gauges etc.), the ignition source may cause an explosion. ► Operate the calibrated leak only in the INFICON battery leak detector ELT3000. WARNING Risk of explosion due to escaping solvent Solvents can escape through a damaged membrane and lead to an explosive concentration in the air. - Page 16 4 | Description INFICON WARNING Risk of injury from flammable solvents The solvent in the calibration leak is highly flammable. Overheating can damage the membrane, solvent can leak and ignite from an ignition source. ► Observe the manufacturer's safety data sheets and follow the applicable work instructions.
- Page 17 INFICON Description | 4 Position Name Calibrated leak (top view) Sticker at calibrated leak Calibrated leak (bottom view) Transport lock (sight glass), wrench size 18 Filling port Table 1: Description of calibrated leak E-Check_Operating-instructions-lime10en1-05-(2007) 17 / 24...
-
Page 18: Markings On The Calibrated Leak
4 | Description INFICON 4.1 Markings on the calibrated leak Item Name Shelf life notice Danger notice Nameplate Table 2: Calibrated leak markings 18 / 24 E-Check_Operating-instructions-lime10en1-05-(2007) -
Page 19: Function
INFICON Description | 4 4.2 Function The solvent DMC in the calibrated leak constantly escapes in gaseous form via a membrane. The membrane is protected by a grid. The calibrated leak is used to calibrate the ELT3000 battery leak detector. -
Page 20: Technical Specifications
4 | Description INFICON 4.3 Technical specifications 4.3.1 Mechanical data Material Aluminum Dimensions (Ø x H) 150 mm x 25 mm Weight (filled) < 900 g 4.3.2 Ambient conditions Temperature range (°C) 10 °C to 40 °C Relative humidity (%) 80% at 30 °C, linear... -
Page 21: Disposal
INFICON Disposal | 5 5 Disposal The device can either be disposed of by the operator or be sent to the manufacturer. The device consists of materials that can be recycled. This option should be exercised to prevent waste and also to protect the environment. -
Page 22: Declaration Of Contamination
6 | Declaration of Contamination INFICON 6 Declaration of Contamination 22 / 24 E-Check_Operating-instructions-lime10en1-05-(2007)