Related Manuals for Advantech ITA-460 Series
Summary of Contents for Advantech ITA-460 Series
- Page 1 User Manual ITA-460 Series Fanless Embedded Industrial ® Computer with 8th/9th Gen Intel Core™ i Processor for Vehicle Applications...
- Page 2 No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable.
- Page 3 Advantech has come to be known. Your satisfaction is our primary concern. Below is a guide to Advantech's customer ser- vices.
- Page 4 Initial Inspection Before setting up the equipment, check that the items listed below are included and in good condition. 1 x ITA-460 series industrial computer 1 x ITA-460 accessory box If any of the above items are missing or damaged, contact your distributor or sales representative immediately.
- Page 5 In accordance with IEC 704-1:1982 specifications, the sound pressure level at the operator's position does not exceed 70 dB (A). DISCLAIMER: These instructions are provided according to the IEC 704-1 specifica- tions. Advantech disclaims all responsibility for the accuracy of any statements con- tained herein. ITA-460 User Manual...
- Page 6 Conformément à la norme CEI 704-1:1982, l’opérateur ne doit pas expérimenter un niveau sonore supérieur à 70 dB (A). AVERTISSEMENT: Ces consignes suivent la norme CEI 704-1. Advantech décline toute responsabilité concernant l'exactitude des déclarations contenues dans ce doc- ument.
- Page 7 Safety Precautions - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from the PC chassis before manual handling. Do not touch any components on the CPU card or other cards while the PC is powered on.
- Page 8 ITA-460 User Manual viii...
-
Page 9: Table Of Contents
Contents Chapter Overview..........1 Introduction ....................2 Specifications .................... 2 Power Information ..................2 Table 1.1: Power Input ..............2 Environmental Specifications ..............3 Table 1.2: Environmental Specifications ........3 System Diagram..................4 Figure 1.1 ITA-460 System Diagram ........... 4 Figure 1.2 ITA-460 Exploded Diagram ........5 Table 1.3: Parts List.............. - Page 10 Figure 3.11CPU thermal pad location ........21 Figure 3.12CPU Socket.............. 22 RTC Battery Installation ................23 Figure 3.13RTC battery location..........23 Chapter BIOS Settings ........25 Introduction ..................... 26 Figure 4.1 Main setup screen ............ 26 Entering Setup ..................26 Figure 4.2 AMI BIOS information screen........
- Page 11 4.5.4 Memory Configuration..............49 Figure 4.29Memory Configuration ..........49 4.5.5 PCH-IO Configuration ..............50 Figure 4.30PCH-IO Configuration..........50 4.5.6 PCI Express Configuration............51 Figure 4.31PCI Express Root Port ..........51 Figure 4.32PCI Express Root Port Setting ......... 51 4.5.7 SATA and RST Configuration ............. 52 Figure 4.33SATA Configuration..........
- Page 12 ITA-460 User Manual...
-
Page 13: Chapter 1 Overview
Chapter Overview Introduction Specifications Power Information Environmental Specifications System Diagram... -
Page 14: Introduction
Introduction ITA-460 is a compact and vehicle computer equipped with a 8th/9th generation Intel® CoreTM i processor, wide voltage input range and special power protection surges design guarding against system damage from transient power. Specifically designed for intelligent transportation and road surveillance applications, It can work in extreme environments with features like the wide working temperature range (-25- 60°C) and anti-shock/vibration to pass MIL-STD-810G;... -
Page 15: Environmental Specifications
Tma Instruction/Installation/Safety 60 degree C whose output meets SELV or ES1 and is rated Manual 9-32Vdc, 8.2A min., if need further assistance, please con- tact Advantech for further information." ITA-460 User Manual... -
Page 16: System Diagram
System Diagram 190.0 216.5 70.0 205.0 R2.5 13.3 Figure 1.1 ITA-460 System Diagram ITA-460 User Manual... - Page 17 Figure 1.2 ITA-460 Exploded Diagram Table 1.3: Parts List Top Cover Main Board Top Rubber Inner Heatsink Waterproof Frame Inner Bracket 1 Bottom Rubber Inner Bracket 2 Power Bracket SSD Module Power Board Bottom Mount Kit ITA-460 User Manual...
- Page 18 ITA-460 User Manual...
-
Page 19: Chapter 2 H/W Installation
Chapter H/W Installation Introduction Jumpers and Connectors I/O Connectors... -
Page 20: Introduction
Introduction The following sections show the internal jumper settings and external connector pin assignments for configuring the system according to application requirements. Jumpers and Connectors 2.2.1 Jumper Description ITA-460 can be configured for specific applications by setting jumpers. A jumper is a metal bridge used to close an electric circuit. -
Page 21: Jumper And Connector Locations
2.2.2 Jumper and Connector Locations The main board features a number of connectors and jumpers for system configura- tion. The location of each jumper and connector on the main board is shown in Figure 2.1. The function of each of the connectors and jumpers is listed in Table 2.1 below. Figure 2.1 Jumper and Connector Locations on Main Board Table 2.1: Jumpers List Name... - Page 22 2.2.2.1 Clear CMOS ITA-460 single board computer contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins 1-2 closed. If you want to reset the CMOS data, set CMOS1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed.
- Page 23 2.2.2.4 COM port RS-485 termination option ITA-460 single board computer contains a jumper that can set Watchdog mode. Table 2.5: TERM1 (COM port RS-485 termination option) TERM1 COM port RS-485 termination option 3 x 2 Pin open FootPrint closed (1-3) and (4-6) Setting Function (1-2)
-
Page 24: I/O Connectors
I/O Connectors Antenna HDMI LED-Power/DATA/LAN1/LAN2 USB 3.0 Audio LAN1/LAN2 Figure 2.2 ITA-460 I/O View 2.3.1 COM Connector ITA-460 is equipped with two RS-232/422/485 DB9 connectors. The default setting is RS-232. Table 2.6: COM Connector Pin Definitions RS-232 RS-422 RS-485 Signal Name Signal Name Signal Name COM1 RTS... -
Page 25: Audio Connector
2.3.2 Audio Connector Table 2.7: Audio Connector Pin Definitions Signal Name Signal Name Line Out R Audio GND Line Out L MIC_R MIC_L 2.3.3 Power Input Connector Table 2.8: Power Input Connector Pin Definitions Signal Name +8VDC~+36VDC IGNITION Connect + VDC over 5V to trig ignition PWRBTN Contact GND to trig power button 2.3.4... -
Page 26: Led Indicators
2.3.5 LED Indicators The ITA-460 front panel features LEDs that are used to indicate system health and active status. The LED indicator behaviors are explained in the table below. Table 2.10: LED Indicators Item Status Color Description Blue The system is powered on and secure. Data is being received/transmitted DATA Not active... -
Page 27: Chapter 3 System Setup
Chapter System Setup mSATA Installation ITA-EM Module Installation RTC Battery Installation... -
Page 28: Introduction
Introduction The following sections provide instructions for installing the hardware modules into the ITA-460 system. mSATA Installation ITA-460 features one mSATA slot on the main board and three mini PCIe slots on the carrier board. Figure 3.1 Bottom screw locations. Figure 3.2 SSD Bracket screw locations ITA-460 User Manual... - Page 29 Figure 3.3 Mini PCIe and mSATA Locations on Main Board Loosen the screws and open the bottom cover of the device. Loosen the screws to remove the dual-SSD bracket. Insert the mSATA or mini PCIe module. Affix the module in place using two screws. ITA-460 User Manual...
-
Page 30: Ssd Installation
SSD Installation ITA-460 is equipped with one SSD bracket that features Dual SSD socket . To install an SDD, follow the instructions provided on the next page. Figure 3.4 SSD Bracket (1) Figure 3.5 Dual-SSD Socket (2) ITA-460 User Manual... - Page 31 Figure 3.6 SATA Cable Assembly Figure 3.7 SSD Screw locations Figure 3.8 SSD socket screw locations ITA-460 User Manual...
- Page 32 Figure 3.9 SATA cable locations Assemble SATA cable with SSD. Install the SSD onto the socket and secure it in place using eight screws two sides. Install the SSD socket onto the bracket and secure it in place using four screws. Install the SATA cable on the MB.
-
Page 33: Cpu Installation
CPU Installation Figure 3.10 Top cover screw locations Figure 3.11 CPU thermal pad location ITA-460 User Manual... - Page 34 Figure 3.12 CPU Socket Loosen the screws and open the Top cover of the device. Tap the CPU thermal pad on the VC of Top cover. Install the CPU onto the CPU socket. ITA-460 User Manual...
-
Page 35: Rtc Battery Installation
RTC Battery Installation Figure 3.13 RTC battery location Open the bottom cover. Insert the RTC battery into the holder and connect the cable. Fix the BTC battery onto the top of USB conn. via double sided foam tape. Note! The RTC battery settings can be configured using the BIOS Setup utility. The +VBAT should be >2.6V. - Page 36 ITA-460 User Manual...
-
Page 37: Chapter 4 Bios Settings
Chapter BIOS Settings... -
Page 38: Introduction
This chapter explains the basic navigation of the BIOS Setup menus and how to con- figure the BIOS settings for the ITA-460 series. With the AMI BIOS Setup program, users can modify the BIOS settings and control the device features. The Setup pro- gram features several menus with multiple items that for enabling/disabling functions and implementing changes. -
Page 39: Main Setup
Main Setup Upon entering the BIOS Setup utility, users are presented with the Main setup page. Users can always return to the Main setup page by selecting the Main tab. The Main BIOS Setup page is shown below. Figure 4.3 Main Setup Screen The Main BIOS setup page has two main frames. -
Page 40: Advanced Bios Features Setup
Advanced BIOS Features Setup Select the Advanced tab from the ITA-460 setup screen to enter the Advanced BIOS setup screen. You can select any of the items in the left frame of the screen, such as CPU configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>... -
Page 41: Platform Misc Configuration
4.4.1 Platform Misc Configuration Figure 4.5 Platform Misc Configuration Platform Misc Configuration – Native PCIE Enable PCI Express Native Support Enable/Disable. This is only available in Vista. – Native ASPM On enable, Vista will control the ASPM support for the device. If disabled, the BIOS will. -
Page 42: Cpu Configuration
4.4.2 CPU Configuration This page shows the version, mode, type, and SKU of the ME firmware built-in BIOS. Figure 4.6 CPU Configuration Hardware Prefetcher Hardware Prefetcher is a technique that fetches instructions and/or data from memory into the CPU cache memory well before the CPU needs it to improve the load-to-use latency. -
Page 43: Power & Performance
4.4.3 Power & Performance This page shows the hardware data accessed by the embedded controller. Users can access this page to obtain the system temperature, voltage, or status informa- tion. Figure 4.7 CPU Power & Performance Power Config Select the power configuration as Max or Limit to 35W Boot Performance ... -
Page 44: Pch-Fw Configuration
4.4.4 PCH-FW Configuration Figure 4.8 PCH-FW Configuration PCH-FW Version PCH-FW page shows Intel ME FW information. ITA-460 User Manual... -
Page 45: Trusted Computing
4.4.5 Trusted Computing Figure 4.9 TPM Settings TPM Support “Enable or Disable” TPM Support. You can purchase Advantech LPC TPM mod- ule to enable TPM function. P/N: PCA-TPM-00B1E. ITA-460 User Manual... -
Page 46: Acpi Setting
4.4.6 ACPI Setting Figure 4.10 ACPI Settings Enable Hibernation Enable or Disable Hibernation (OS/S4 Sleep State). This option may not be applied in some OS. ACPI Sleep State Auto or S1 only or S3 only ACPI Sleep State. Lock Legacy Resources ... -
Page 47: Smart Settings
4.4.7 SMART Settings Figure 4.11 SMART Settings SMART Self Test Enable or Disable SMART Self Test on all HDDs during POST 4.4.8 Ignition Configuration Figure 4.12 Ignition Configuration ITA-460 User Manual... -
Page 48: It8528 Hw Monitor
4.4.9 IT8528 HW Monitor Figure 4.13 PC Health Status CPU(PECI) Warning Temperature Use this item to set the CPU warning temperature. When the system reaches the warning temperature, the speaker will beep. CPU(PECI) ACPI Shutdown Use this item to set the ACPI shutdown temperature. When the system reaches the shutdown temperature, it will be automatically shut down by the ACPI OS to protect the system from overheating damage. - Page 49 Figure 4.15 Serial Port 1 Configuration Figure 4.16 Serial Port 2 Configuration ITA-460 User Manual...
- Page 50 Figure 4.17 Serial Port 2 Configuration Serial Port 1 Configuration – Serial Port This item allows users to enable or disable Serial Port. – Change Settings This item allows users to Change Settings of the Serial Ports. The default setting is Auto.
-
Page 51: S5 Rtc Wake Setting
4.4.11 S5 RTC Wake Setting Figure 4.18 S5 RTC Wake Settings Wake system with Fixed Time To Enable or Disable System wake on alarm event. The system will wake on the hr:min:sec as specified. ITA-460 User Manual... -
Page 52: Serial Port Console Redirection
4.4.12 Serial Port Console Redirection Figure 4.19 Serial Port Console Redirection COM1 – Console Redirection Settings Console Redirection Enable or Disable Legacy Console Redirection – Legacy Console Redirection Settings Legacy Console Redirection Settings Serial Port for Out-of-Band Management/ Windows Emergency Manage- ... -
Page 53: Intel Txt Information
4.4.13 Intel TXT Information Figure 4.20 Intel TXT Information ITA-460 User Manual... -
Page 54: Usb Configuration
4.4.14 USB Configuration Figure 4.21 USB Configuration Legacy USB Support This is for supporting USB device under legacy OS such as DOS. When choos- ing Auto, the system will automatically detect if any USB device is plugged into the computer and enable USB legacy mode when a USB device is plugged and disable USB legacy mode when no USB device is plugged. -
Page 55: Csm Configuration
4.4.15 CSM Configuration Figure 4.22 CSM Configuration Compatibility Support Module Configuration – CSM Support Enable/Disable CSM Support. CSM16 Module Version – GateA20 Active Upon Request - GA20 can be disabled using BIOS services. Do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. -
Page 56: Network Stack Configuration
– Other PCI devices Determines OpROM execution policy for devices other than Network, Stor- age, or Video. 4.4.16 Network Stack Configuration Figure 4.23 Network Stack Configuration ITA-460 User Manual... -
Page 57: Chipset Configuration
Chipset Configuration The PCH and SA setting can be configured via the Chipset Configuration sub-page. Figure 4.24 Chipset This page (SAprovides information of the chipset on ITA-460. ITA-460 User Manual... -
Page 58: System Agent (Sa) Configuration
4.5.1 System Agent (SA) Configuration Figure 4.25 System Agent (SA) Configuration VT-d This item allows users to enable/disable VT-d function. Above 4GB MMIO BIOS Assignment This item allows users to enable/disable above 4 GB MMIO BIOS assignment. When the aperture size is 2048 MB, this function is automatically disabled. Graphics Configuration ... -
Page 59: Graphics Configuration
4.5.2 Graphics Configuration Figure 4.26 Graphics Configuration Primary Display Set Primary Display to "Auto", "IGFX", "PEG", "PCI", or "SG". Primary Display Select PEG0/PEG1/PEG2/PEG3 graphics device should be Primary PEG. External Gfx Card Primary Display Configuration Internal Graphics ... -
Page 60: Peg Port Configuration
4.5.3 PEG Port Configuration Figure 4.27 PEG Port Configuration Figure 4.28 PEG Port Feature Configuration Enable Root Port Enable or disable the root port Max Link speed Configure PEG 0:1:0 max speed PEG Port Feature Configuration- Detect Non-Compliance Device ... -
Page 61: Memory Configuration
4.5.4 Memory Configuration Figure 4.29 Memory Configuration Maximum Memory Frequency Maximum memory frequency selections in Mhz ITA-460 User Manual... -
Page 62: Pch-Io Configuration
4.5.5 PCH-IO Configuration Figure 4.30 PCH-IO Configuration LAN1 Controller Enable or Disable LAN1 controller. LAN 1 Option-ROM Enable or Disable LAN 1 boot option for legacy network devices. LAN2 Controller Enable or Disable LAN2 controller. LAN 2 Option-ROM ... -
Page 63: Pci Express Configuration
4.5.6 PCI Express Configuration This page shows that the PCH supports the PCIE root ports. PCIE port 4 is assigned to i219 LAN. The items for configuration are show below. Figure 4.31 PCI Express Root Port Figure 4.32 PCI Express Root Port Setting PCI Express Root Port 1 ... -
Page 64: Sata And Rst Configuration
4.5.7 SATA and RST Configuration Figure 4.33 SATA Configuration SATA Controller(s) Enable or Disable SATA Controller SATA Mode Selection This can be configured as RAID or AHCI. SATA Controller Speed Indicates the maximum speed the SATA controller can support by selecting. Default, Gen1, Gen2, Gen3. -
Page 65: Usb Configuration
4.5.8 USB Configuration Figure 4.34 USB Configuration XHCI Compliance mode Option to "Enable or Disable" XHCI compliance mode. Default is to disable com- pliance mode. ITA-460 User Manual... -
Page 66: Security Configuration
4.5.9 Security Configuration Figure 4.35 Security Configuration RTC Memory Lock Enable will lock bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM. BIOS Lock "Enable or Disable" the PCH BIOS Lock Enable feature. Required to be enabled to ensure SMM protection of flash. -
Page 67: Hd Audio Configuration
4.5.10 HD Audio Configuration Figure 4.36 HD Audio Configuration HD Audio Control detection of the HD-Audio device. Disable = HDA will be unconditionally disabled Enable=HDA will be unconditionally enabled ITA-460 User Manual... -
Page 68: Security
Security Figure 4.37 Security In the BIOS Setup utility, select the Security tab. To access the submenu for any of the items, select the item and press <Enter>. Administrator Password This item allows users to set the administrator password. The ideal password length is between 3 and 20 characters. -
Page 69: Boot
Boot Figure 4.38 Boot Setup Prompt Timeout Use the <+> and <-> keys to adjust the number of seconds to wait for setup acti- vation key. Bootup NumLock State “On or Off” power-on state for the NumLock. Quiet Boot ... -
Page 70: Save & Exit
Save & Exit Figure 4.39 Save & Exit Save Changes and Exit When you complete system configuration, select this option to save your changes, exit BIOS setup and reboot the computer so the new system configuration parame- ters can take effect. Select Exit Saving Changes from the Exit menu and press <Enter>. -
Page 71: Chapter 5 Driver Installation
Chapter Driver Installation Introduction Windows Driver Setup... -
Page 72: Before You Begin
The chipset driver is used for the following versions of Windows, and it has to be installed before installing all the other drivers: Windows 10 (64bit) Windows Driver Setup Enter the Advantech support website, then search product ITA-460. You can see “ITA-460" driver inside. ITA-460 User Manual... -
Page 73: Appendix A Watchdog Timer
Appendix Watchdog Timer... -
Page 74: Programming The Watchdog Timer
Programming the Watchdog Timer The ITA-460’s watchdog timer can be used to monitor the software operations and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and procedures for pro- gramming it. - Page 75 Table A.2: Watchdog (Warm Reset) Sample Code #include <cstdlib> #include <sys/io.h> #include <unistd.h> #include <iostream> using namespace std; int OBF=0x01, IBF=0x02 int wait_OBF(int Port) int icount; for(icount=0;icount<0xFF;icount++) int iValue = inb(Port); if((iValue&OBF) == 0x01) return true; usleep(1000); count<< “Wait_OBF failed\n”; count.flush();...
- Page 76 Table A.2: Watchdog (Warm Reset) Sample Code void SetWD() iopl(3); DummyPort(); inb(0x299); wait_IBF(0x29A); outb(0x89, 0x29A); wait_IBF(0x29A); outb(0x5E, 0x299); wait_IBF(0x29A); outb(0x00, 0x299); wait_IBF(0x29A); outb(0x89, 0x29A); wait_IBF(0x29A); outb(0x5F, 0x299); wait_IBF(0x29A); outb(0x64, 0x299); void StartWD() iopl(3); DummyPort(); outb(0x89, 0x29A); wait_IBF(0x29A); outb(0x57, 0x299); wait_IBF(0x29A); outb(0x04, 0x299);...
-
Page 77: Appendix Bbsmi Rohs Declaration
Appendix BSMI RoHS Declaration... - Page 78 BSMI RoHS 限用物質含有情況標示確認表 Declaration of the Presence Condition of the Restricted Substances Marking 設備名稱：電腦 型號 （型式） ：ITA-460 Equipment name Type designation (Type) 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 六價鉻 多溴聯苯 多溴二苯醚 鉛 汞 鎘 Unit Hexavalent Polybrominated Polybrominated Lead Mercury Cadmium...
-
Page 79: Chinese Language Safety Instructions And Battery Information
Appendix Chinese Language Safety Instructions and Battery Information... -
Page 80: 安全指示
安全指示 請仔細閱讀此安全操作說明。 請妥善保存此用戶手冊供日後參考。 用濕抹布清洗設備前，請從插座拔下電源線。請不要使用液體或去汙噴霧劑清洗 設備。 對於使用電源線的設備，設備周圍必須有容易接觸到的電源插座。 請不要在潮濕環境中使用設備。 請在安裝前確保設備放置在可靠的平面上，意外跌落可能會導致設備損壞。 設備外殼的開口是用於空氣對流，從而防止設備過熱。請不要覆蓋這些開口。 當您連接設備到電源插座上前，請確認電源插座的電壓是否符合要求。 請將電源線佈置在人們不易絆到的位置，並不要在電源線上覆蓋任何雜物。 請注意設備上的所有警告標識。 如果長時間不使用設備，請將其同電源插座斷開，避免設備被超標的電壓波動損 壞。 請不要讓任何液體流入通風口，以免引起火災或者短路。 請不要自行打開設備。為了確保您的安全，請由經過認證的工程師來打開設備。 如遇下列情況，請由專業人員來維修： 電源線或者插頭損壞； 設備內部有液體流入； 設備曾暴露在過於潮濕的環境中使用； 設備無法正常工作，或您無法通過用戶手冊來使其正常工作； 設備跌落或者損壞； 設備有明顯的外觀破損。 請不要把設備放置在超出我們建議的溫度範圍的環境，即不要低於 -25°C （-13 °F）或高於 60°C （140°F） ，否則可能會損壞設備。 此為 A 級產品，在生活環境中，該產品可能會造成無線電干擾。在這種情況下， 可能需要使用者對干擾採取切實可行的措施。 本產品不帶電線元件銷售，應購買已通過 CCC 認證的電線元件。 注意：電腦配置了由電池供電的即時時鐘電路，如果電池放置不正確，將有爆炸的危 險。因此，只可以使用製造商推薦的同一種或者同等型號的電池進行替換。請按照製 造商的指示處理舊電池。 根據... - Page 81 ITA-460 User Manual...
- Page 82 No part of this publication may be reproduced in any form or by any means, such as electronically, by photocopying, recording, or otherwise, without prior written permission from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2021...
Need help?
Do you have a question about the ITA-460 Series and is the answer not in the manual?
Questions and answers