Related Manuals for Hyundai power products HBC12V2A
Summary of Contents for Hyundai power products HBC12V2A
- Page 1 CORDLESS IMPACT WRENCH HBC12V2A ORIGINAL INSTRUCTIONS WARNING: READ THE FOLLOWING INSTRUCTIONS BEFORE USING THIS MACHINE.
-
Page 2: Table Of Contents
CONTENTS 1. INTENDED USE 2. SAFETY INSTRUCTIONS 3. EXPLANATION OF SYMBOLS 4. YOUR PRODUCT 5. TECHNICAL DETAILS 6. OPERATION 7. MAINTENANCE 8. DISPOSAL 9. DECLARATION OF CONFORMITY 10. WARRANTY 11. PRODUCT FAILURE 12. WARRANTY EXCLUSIONS... -
Page 3: Intended Use
1. INTENDED USE The cordless impact wrench is designed to driving or removes nuts by using couplers which are not provided with this tool. You can buy 3/8 square coupler to use with this tool. 2. SAFETY INSTRUCTIONS 2.1 GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. - Page 4 e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
- Page 5 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. b) Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
- Page 6 Charger Use the charger provided with the tool only to charge the battery. Never attempt to charge non-rechargeable batteries. Have defective cords replaced immediately. Do not expose to water. Do not open the charger. Do not probe the charger. ...
-
Page 7: Explanation Of Symbols
3. EXPLANATION OF SYMBOLS To reduce the risk of injury, the user must read and understand this manual before using this product. Conforms to relevant safety standards Do not expose batteries to temperatures exceeding 40 degrees. Do not dispose of batteries in fire. They could explode and cause injury Do not dispose of batteries in water. -
Page 8: Your Product
4. YOUR PRODUCT 1. 3/8“anvil 2. LED light 3. On/Off trigger switch 4. Battery release button 5. Hand grip 6. Forward/Reverse switch 7. Battery capacity indicator 8. Charger 9. Li-ion battery pack 10. Charger indicator light... -
Page 9: Technical Details
5. TECHNICAL DETAILS Voltage......12V d.c. Torque ......120Nm Coupler ......3/8” (9.525mm) Speed......0-2700/min Impact frequency………0-40500BPM Battery Pack……………DC033, 12V d.c. 2000mAh, 24Wh Li-ion battery Charger………………...DC122400, input 220-240V~, 50-60Hz, 50W, output 12V d.c., 2.4A Sound power level L ..73.2dB(A), K= 3dB(A) Sound pressure level L ..84.2dB(A) K= 3dB(A) Vibration...... -
Page 10: Operation
6. OPERATION 6.1 CHARGING IMPORTANT: The battery pack is not fully charged at the factory. Before attempting to charge them, thoroughly read all of the safety instructions. To assure that the charger (8) you use are applicable to the battery pack (9). 2) Insert the charger into 220-240V~, 50-60Hz outlet. -
Page 11: Maintenance
Caution: To prevent gear damage, always allow the anvil to come to a complete stop before changing the direction of rotation, Note: The wrench will not run unless the direction of rotation selector is pushed fully to the left or right.Avoid running the wrench at low speeds for extended periods of time. -
Page 12: Disposal
ZI, 32, rue Aristide Bergès- 31270 Cugnaux-France Tel: + 33 (0) 5.34.502.502 Fax: + 33 (0) 5.34.502.503 Declares that the machinery designated below: Cordless impact Wrench HBC12V2A Serial number: 20210635543-20210636842 Complies with the provisions of the Directive «machinery» 2006/42/CE and national laws... -
Page 13: Warranty
10. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 14: Product Failure
11. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 15: Warranty Exclusions
12. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...
Need help?
Do you have a question about the HBC12V2A and is the answer not in the manual?
Questions and answers