Page 2
30 days after the transfer of risks. In the event of justified notice of compliant, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract.
Page 3
Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.
Page 4
Operators Safety Summary The general safety information in this summary is for operating personnel. Do Not Remove Covers or Panels There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.
Page 5
Change History The table below lists the changes to the User’s Guide Addendum. Date ECP # Description Approved By 6/22/12 597847 Initial Release R. Pellicano 26-0904001-00 Rev 00.00...
1. Getting Started To get started, make sure you have an ImagePRO-II Dual Output unit (R9004683) or obtain a Dual Channel Option Card kit (R9004684) to upgrade an existing ImagePRO-II unit If you are not certain what type of unit you have contact your local Barco Sales Representative for more information.
1) Within the SYSTEM menu, scroll to and select the OUTPUT CONNECTOR MAP submenu 2) By default, all seven outputs of the ImagePRO-II will be mapped to Output A. 3) Scroll to the various connectors as required and change the field from A to B to map that connector to Output B.
3. Output Configuration Once the mode and connectors have been setup, specific configuration of the two outputs can be performed. Output Resolution 1) In the OUTPUT setup menu, the first two lines (labelled CHA and CHB) show the current resolution and frame rate for each channel. 2) Select either of these menu items to change the output resolution / frame rate to the desired choice.
Output Effects 1) Select the EFFECTS submenu under OUTPUT. 2) The first field (labelled CHANNEL) allows the selection of A, B or ALL to allow for independent or simultaneous adjustments for each output. Genlock 1) Select the GENLOCK submenu under OUTPUT. 2) The first field (CHA SOURCE) can be selected and will offer all the standard Genlock source options (FREERUN, EXT or IN #).
Pan / Zoom 1) Select the PAN/ZOOM button on the front panel of the ImagePRO-II. 2) The first field (labelled CHANNEL) allows the selection of A or B to allow independent Pan and Zoom adjustments for each output channel.
4. General Operation 1) In addition to the input and output connectors provided in ImagePro-II, the ImagePro-II Dual output unit provides a second SDI input (SDI 6) and associated loop-through as well as a second SDI output (SDI 2 OUT).
5. Remote Commands The following commands have been updated as of software release 02.00.02. Description: Input Channel Settings Required parameters: --con (connector) --ch (channel) --itype (input type), only for commands to DVI connector Parameters: --con (connector) : 0-5, see below for input connector numbers. --ch (channel) : 0-1, input channel --itype (input type) : 0 = digital, 1 = analog...
Query Format 2 (Input window): ICH --con (connector) --ch (channel) --iwin --? Query Response 2 : Input Channel Window Setting in the following format ICH --hpos (H Position) --vpos (V Position) --hsize (H Size) --vsize (V Size) Query Format 3 (Mask): ICH --con (connector) --ch (channel) --mask --? Query Response 3 : Input Channel Mask Setting in the following format ICH --left (Left) --right (Right) --top (Top) --bottom (Bottom) Connectors:...
SYSMGR Description: System Manager Settings Parameters: --blkinv (Black Invalid Mode) : 0=OFF, 1=ON --vfd (VFD Brightness) : 0..6 --opmode (Operation Mode) : 0=SingleChannel, 1=DualChannel, 2=3DProcessing Note: For the new operating take full effect, you must save settings and reboot the unit.
Description: Video Format Settings Required parameters: --con (connector) , for input video format --och (output channel) , for output video format --itype (input type) , for commands to DVI Input settings Parameters: --con (connector) : 0-5, see below for input connector numbers. --och (output channel) : 0-1, for output commands --itype (input type)