Page 2
Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/en/support Visit us at the web: www.barco.com Printed in Belgium...
Page 3
Barco. If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser...
Page 4
This software and the accompanying files are sold “as is” and without warranties as to performance or mer- chantability or any other warranties whether expressed or implied. In no event shall Barco be liable for damage of any kind, loss of data, loss of profits, business interruption or other pecuniary loss arising directly or indirectly.
Page 5
Preparing the projector for ICMP upgrade ..............30...
Page 6
Table of contents R5905722 ICMP 09/11/2016...
ICMP, such as safety related issues, initial inspection, minimum version of projector software, etc. This document can be used as a guideline to upgrade the Barco projector with the ICMP or to replace an installed ICMP in the field.
(not applicable for DP2K S series). • Be careful never to drop anything into the ICMP assembly during the procedure. The fall of a tool or a spare part in the ICMP or in the projector could have catastrophic consequences when you will restart the system.
• To avoid any risk of injury, the SERVICE PERSONNEL that do the installation or maintenance of the ICMP must respect the same rules as for the projector. Follow the safety instructions listed in the projector manuals. Installation requirements...
Barco Sales and the Service office should be notified as soon as possible. Unpacking At delivery the ICMP is packed in a cardboard box. Place the cardboard box on a stable (solid), flat and insulated support during all the unpacking. Open the box from the top. Remove the ICMP that is packaged in an antistatic bag.
Page 11
ICMP are deleted. As a result the ICMP goes into a non recoverable FIPS error state and makes the ICMP out of order. If this is the case, the ICMP must be sent back to factory to install new DCI certificates. Contact Barco technical support.
ICMP introduction About ICMP The ICMP is a removable electronic assembly situated in the Card Cage of the projector. The ICMP stores, decrypts and decodes DCI cinema content and delivers it to the projector in a usable format, all integrated into a single assembly placed directly in the projector.
ICMP HDD About ICMP HDD The three HDDs (local storage) in the ICMP, are set up in a RAID 5 configuration. This storage technique, that combines multiple HDD components into a logical unit, manages enough redundancy information to continue to operate properly after the loss of one HDD.
Page 15
Exchange or re-use of a disk set It’s possible to have several sets of disks with one ICMP or to reuse a complete set of disks coming from another projector with ICMP. It is sufficient to insert the three HDDs, from a valid RAID array, and let the system explore the new RAID.
ICMP outputs sixteen audio signals equitably distributed over these two RJ45 connectors, which can be configured independently. The mapping of audio channels (content) on each audio output (AES outputs of the ICMP) is performed by configuring the ICMP via the Communicator software. Please refer to the Communicator user guide for further information.
ICMP is done via the same IP address as the projector. USB 2.0 The ICMP can be connected to a USB 2.0 Media to load content. The USB port can be used to load content (DCP) or keys (KDM).
2. ICMP functionality 3G-SDI A (B) SDI connector to connect a video source. HDMI HDMI connector to connect a video source. ICMP DisplayPort specifications DisplayPort Digital display interface developed by the Video Electronics Standards Association (VESA). This royalty-free interface is primarily used to connect a video source to a display device such as a computer monitor, though it can also be used to transmit audio, USB, and other forms of data.
Page 19
2. ICMP functionality Port Display Mode 2D Formats / Single DP Color depth 2048 x 1536 @ 60 fps 8 bpc, 10 bpc Single 2048 x 2160 @ 30, 48, 50, 60 fps 8 bpc, 10 bpc Single 3840 x 2160 @ 24 fps...
2. ICMP functionality ICMP SDI specifications 3G-SDI Serial Digital Interface (SDI) is a serial link standardized by ITU-R BT.656 and the Society of Motion Picture and Television Engineers (SMPTE). SDI transmits uncompressed digital video over 75-ohm coaxial cable within studios, and is seen on most professional video infrastruc- ture equipment.
Page 21
2. ICMP functionality 3G HD-SDI signal 1080p 50/60 (Level A) 3Gb/s 1080p 4:4:4 (Level B) 3G HD-SDI uses a higher data rate (2.97 Gb/s). This allows a single cable interface to achieve the same capabilities of a Dual-Link HD-SDI implementation.
Page 22
2. ICMP functionality Frame Rate Display Rate SMPTE Standard Source Scan Type Resolution SMPTE 274M 1920 x 1080 23.976 23.976 Segmented frame SMPTE 428-9 2048 x 1080 Y Cb Cr 4:2:2 10-Bit (SMPTE RP211) 29.97 29.97 SMPTE 274M 1920 x 1080 Interlaced 29.970...
Page 23
2. ICMP functionality The standard HD-SDI interfaces support the Y Cb Cr colorspace (both legal and full range) using 4:2:2 color subsampling. The Dual-Link HD-SDI interface can be used to carry a single 4:4:4 image, having a color depth of 10 or 12 bit per component.
All input resolutions are scaled towards the desired resolution specified in the screen presentation file. ICMP status LEDs ICMP status LEDs and Reset button LEDs on ICMP front panel give information on the status of the device. Image 2-7 Status overview PWR/ERROR and READY LEDs:...
Note: The disk status (RAID degraded) can be from the ICMP", page 35, and "Installing a retrieved via the (Web) Commander. See user HDD into the ICMP", page 33. Ensure to insert guide of the (Web) Commander. the HDD firmly.
4. If problem remains contact Service for further instructions. In case the ICMP has to be returned to factory (e.g. for repair) the non defective HDDs should be removed and kept. 2.10 ICMP reset This procedure requires that ICMP version 1.2.4 or later is installed.
The device certificate (*.pem) of the Barco ICMP is a digital certificate signed by Barco which is required when ordering the KDM to play a DCP that is ingested on the ICMP. The device certificate is stored inside the ICMP and on a web server.
Page 29
2. ICMP functionality Studios Device manufacturer Barco signed X.509 device certificate (PKI CA) BARCO-ICMP-0123456789.pem Content distributors (Key supplier) .pem 0123456789 ICMP Communicator, Commander, Web Commander. Image 2-10 Trusted Device List (TDL) The Goal of the TDL is to maintain timely and accurate information on participating auditori- ums so that participating subscribers can obtain information needed to issue KDMs.
About ICMP configuration Following parameters are available to configure the ICMP: • Global settings: allows defining name of the ICMP, host name (network identifier) and IP address which can be used for communication with external content devices. • User settings: definition of all users allowed on the ICMP.
Page 31
About the ICMP internal clock The crystal on the ICMP board that manages the clock shows a certain drift (all crystals do). With the Communicator the internal clock can be adjusted. This maintenance action should be repeated every 3 months.
HDD input slots and install all three HDDs as described in the procedure "Installing a HDD into the ICMP", page 33. Make sure that all HDDs in the ICMP HDD set have the same storage capacity. See label on top of the HDD to know the storage capacity.
Barco website. c) Check if the ICMP is updated with the latest software. At least version 1.2.4 should be installed. The (WEB) Commander or Communicator can be used to retrieve the version of the installed ICMP software.
Page 35
PH2 Phillips screwdriver. • 2.5mm Allen wrench. How to prepare the projector for upgrading with ICMP? 1. Startup the projector and create a full backup clone package. For detailed instructions see user guide of the Communicator. 2. Switch off the projector and wait 15 minutes before proceeding with this procedure. This to allow the projector to complete the cooling down cycle and to discharge the capacitors.
Caution: Ensure that the both sides of the ICMP are captured by the guides inside the Card Cage compartment. See detail in image below. 2. Push (apply a little pressure) on both handles until the ICMP is fully inserted and the connection is made with the back plane.
3. ICMP installation 7. Proceed with retrieving the device certificate from the ICMP for ordering the correct KDMs to play Dig- ital Cinema Packages (DCPs). For detailed instructions see user guide of the (WEB) Commander or Communicator. Replacing the ICMP in the Card Cage of the projector will result in tamper events (service door tamper, insertion tamper).
Page 38
Image 3-6 5. Switch on the projector. In case you replace one HDD (e.g. degraded mode) the ICMP automatically starts with the RAID recovery process. The red LED of the HDD which has to be rebuilt is blinking. This process takes about 200 GB per hour. Once the RAID is completed the red LED turns off.
Using the CertID label to download the ICMP certificate 1. Scan the QR code (reference 1) on the front face of the ICMP with a smartphone. It’s recommended to use a smartphone with auto-focus. The QR reader will automatically redirect to the ICMP certificate download page on the web server.
Page 40
Image 3-8 3. Push the unlock button to open the handle. Image 3-9 4. Pull the HDD out of its slot. Image 3-10 To install the HDD see procedure "Installing a HDD into the ICMP", page 33. R5905722 ICMP 09/11/2016...
Video watermarking: Civolution NexGuard Audio watermarking: Civolution Closed captioning devices: Support for SMPTE 430-10 * 4K 24fps is standard. For 4K 60p / 4K 3D on ICMP upgrade modules a license is required. Newly-built 4K Barco Alchemy projectors have the license standard included.
Barco Escape license Dual Projector license Live 3D*** Ghostbusting*** * 4K 24fps is standard. For 4K 60p / 4K 3D on ICMP upgrade modules a license is required. New-built 4K Barco Alchemy projectors have the license standard included *** Software roadmap About General Purpose Inputs &...
General Purpose outputs The Barco Cinema Controller and the Barco ICMP have each eight (8) opto-isolated outputs available. Four (4) of the outputs on the Cinema Controller are dedicated for TI. The other general purpose outputs can be controlled via software.
GPIO of the Cinema Controller via two predefined Macros (not editable). Not with the GPIO of the ICMP. The GPO signals of the ICMP will return to their default output level when the projector is switched to Sleep mode. This could generate unexpected "Falling Edge" triggers at the output pins. Also when awakening the projector (from Sleep mode to Standby mode) the GPO signals of the ICMP may generate unexpected "Rising Edge"...
Page 46
AES 3&4 +minus White/Brown White/Brown AES 7&8 +plus Brown Brown AES 7&8 +minus 568A and 568B may be used interchangeably in a system SO LONG AS both ends of a given cable are terminated the same way. R5905722 ICMP 09/11/2016...
Page 47
568A + 568B wiring is a crossover cable. 568A + 568A wiring is a straight cable. 568B + 568B wiring is a straight cable. The mapping of the channels is done according to the Ethernet wiring scheme and gives us 100 Ohm per pair. R5905722 ICMP 09/11/2016...
Page 48
A. Technical specifications R5905722 ICMP 09/11/2016...
Electronic Products” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
Page 50
Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environ- ment-friendly use period of electronic information products” of Chinese Mainland.
USB, and other forms of data. VESA designed it to replace VGA, DVI, and FPD-Link. Backward compatibility to VGA and DVI by using active adapter dongles enables users to use DisplayPort fitted video sources without replacing existing display devices. R5905722 ICMP 09/11/2016...
Page 54
fines a new SuperSpeed mode with a signaling speed of 5 Gbit/s and a usable data rate of up to 4 Gbit/s (500 MB/s). A USB 3.0 port is usually colored blue, and is backwards compatible with USB 2.0. R5905722 ICMP 09/11/2016...