Error Messages; Using With Headphones; Troubleshooting Specifi Cations - Panasonic SC-ZT2 Operating Instructions Manual

Error messages

Display
CANCEL MUTE FUNCTION
(Scrolling)
MUTE (Blinking)
NOT POSSIBLE FOR
THIS INPUT SOURCE (Scrolling)
NOT POSSIBLE FOR
THIS PCM SOURCE (Scrolling)
NOT POSSIBLE WHEN USING
HEADPHONES (Scrolling)
REMOTE 2
REMOTE 1
SWITCH OFF POWER
(Scrolling)
TURN OFF DTS FIX MODE
(Scrolling)
U701
U703
U704

Using with headphones

Turn down the volume as closest as to the minimum value.
• Plug type: ø 3.5 mm stereo mini plug
W (Headphone) jack
Specifi cations
Power supply differ depending on the symbols (E, GN, GS) indicated on the packaging box.
MAIN UNIT
g PRE AMPLIFIER SECTION
Input sensitivity / Input impedance
TV, AUX3
S/N ratio (IHF A)
BD/DVD, TV, AUX1,
AUX2 (Digital Input)
Tone controls
BASS
50 Hz, + 6 to – 6 dB
TREBLE 20 kHz, + 6 to – 6 dB
Input/Output terminal
AUDIO IN
( TV, AUX3 )
DIGITAL AUDIO IN
OPTICAL 1, 2 ( TV, AUX2 )
AUDIO OUT
( FRONT L/R, SURROUND L/R )
SUBWOOFER OUT
HEADPHONE OUT ( 16 to 64 Ω )
AV
HDMI IN ( BD/DVD, AUX1 )
HDMI OUT ( TO TV (ARC))
This system supports "HDAVI Control 4" function.
Check point/Cause/Countermeasure
• The test signal is not output while muting is on.
Cancel muting for operation.
• This is always displayed while muting is on.
• You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic for dual
sounds.
• You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic effect with
PCM signals with sampling frequency of over 48 kHz.
• You cannot use the sound field effects when using headphones.
• Set the same remote control code for this main unit and remote control. When "REMOTE 2 "
is displayed, set the code to "2 " on the remote control in step 4 of procedure "When other
equipment (mini component system, AV amp, etc.) manufactured by Panasonic operates
with the remote control operations of this system". When "REMOTE 1 " is displayed, set the
code to "1 " on the remote control in step 4 in the same way.
• While "F70
available. Turn off the system, unplug the AC mains lead, and consult your dealer.
• When each input is fixed to DTS (DTS FIX), the sound field effects cannot be
cancelled even if you press [–SETUP, OFF]. Cancel DTS FIX.
• The equipment connected by the HDMI cable is not compatible with this
system's copyright protection technology.
• A problem has occurred with the HDMI connection. Try the following to correct
the problem. Consult your dealer if the error code remains on the display.
– Turn the connected equipment off and on again.
– Disconnect the HDMI cable then reconnect it.
– Do not connect more than 2 sets of equipment to this system's output.
• The system received incompatible video signals through HDMI connection.
Check the settings of the connected equipment.
Headphones
(not supplied)
g MAIN UNIT GENERAL
Power supply
600 mV / 47 kΩ
Power consumption
In standby condition
In standby condition ( HDMI off mode )
80 dB (IHF '66)
Dimensions ( W x H x D )
Mass
Operating temperature range
Operating humidity range
g WIRELESS SECTION
Frequency of the using band
2
Number of using channels
The reaching distance
2 ∗1 It is under the condition as follows.
At same room indoor, there is not an obstacle
between the main unit and the speaker.
4
And installing a main unit in the position with
1
equal to or more than 50 cm height.
1
SPEAKER
g POWER AMPLIFIER SECTION
2
RMS output power (at AC 220 to 240 V)
1
10 % total harmonic distortion
Woofer Speaker ch
Mid High Speaker ch
System Total Power
" is displayed, all operations but turning ON/OFF operation are not
Note
• Avoid listening for prolonged periods of time to prevent hearing
damage.
• Multi-channel signals are forcibly converged to 2-channel and
output. (2CH MIX)
However, for DVD audio, the front left and right signals are output.
• Excessive sound pressure from earphones and headphones can
cause hearing loss.
For E, GN AC 220 to 240 V, 50 Hz
For GS AC 110 to 240 V, 50/60 Hz
16 W
0.5 W
0.2 W
430 mm x 59 mm x 262 mm
Approx. 2 kg
0 °C to 40 °C
20 % to 80 % RH (no condensation)
2.4000 GHz to 2.4835 GHz
3
15 m ∗1
∗2
60 W (100 Hz, 3 Ω)
20 W (1 kHz, 8 Ω)
∗3 160 W (80 W + 80 W)
DIN output power (at AC 220 to 240 V)
1.0 % total harmonic distortion
100 Hz Woofer Speaker ch
1 kHz Mid High Speaker ch
System Total Power 110 W (55 W + 55 W)
∗3
g SPEAKER SECTION ∗2
2 way 5 speakers system (Bass reflex type)
Woofer part 12 cm cone type × 1
Mid High part 2.4 × 10 cm flat type × 4
g SPEAKER GENERAL ∗2
Power supply For E, GN AC 220 to 240 V, 50 Hz
For GS AC 110 to 240 V, 50/60 Hz
Power consumption
Wireless link standby
In standby condition
Dimensions ( W x H x D ) 290 mm × 1231 mm × 290 mm
Mass
Operating temperature range
Operating humidity range
20 % to 80 % RH (no condensation)
∗2 : per 1 speaker
∗3 : use 2 speakers
Note: 1. Specifications are subject to change
without notice.
2. Total harmonic distortion is measured by
the digital spectrum analyser.
3. Total harmonic distortion is measured by
using AES17 filter.
Pages
22
22
—
19
below
26
—
26
—
—
—
40 W (3 Ω)
15 W (8 Ω)
20 W
0.8 W
0.15 W
Approx. 3.9 kg
0 °C to 40 °C
27
VQT2R71