Table of Contents
Advertisement
DYNAMIX HP-51M Coax MDU Master Bridge User's Guide
[-s
<set>
[-c
<act/deact>]
[-p
<port>]
snmptrapserver
[-a
<ip>]
[-m
[-l
<on/off>]
[-u
<on/off>]
[-s
<on/off>]
snmptrapsetup
[-d
<on/off>]
[-c
<act/deact>]
[-r
<refresh time>]
[-z
<time zone>]
[-s
<set> -a address]
sntp
[-r]
stat
[-p
<lan1/lan2>
[-s
<auto /10h /10f
swconfig
/100h /100f>] ]
[-c
<on/off>]
[-t
<QueryInterval
(4~510, even
swigmp
number)>]]
[-q
<queue>
[-w
[-d
<discard mode>]]
swqos
[-p
<lan1/lan2>
[-d
<tx/rx>]
[-c
<on/off>]
swqosrate
[-r
<N (1~1563
rate=N*64kbps)>] ]
[-s
<set>
[-c
<act/deact>]
[-p
<port>
-q
swqostc
[-m
<mac>]
swsmac
Display or set up SNMP trap server(s) configuration.
<set>: trap server index, at most 5 servers (0~4)
<act/deact>: activate or de-activate trap server IP
<port>: SNMP trap UDP port number (0~65535), default
<community>] ]
<ip>: trap server IP address
<community>: trap server community name, default 'public'
Enable or disable specified trap type,
<on/off>: turn on or turn off this trap type, default is
-l: logon/logoff trap
-u: upload/upgrade firmware/driver trap
-s: EP on-line status changed trap
-d: EP diagnosis trap
Display or set up SNTP configuration for
<act/deact>: activate or de-activate SNTP service for system
time
<refresh
<time
and
<set>: 2 registered SNTP server set(0~1)
address: SNTP server host name or IP address in current set
Display port statistics for port LAN1/LAN2/HCNA.
-r: reset all port statistics counter to 0
Display or set up Ethernet port LAN1/LAN2 properties
<lan1/lan2>: configure LAN1 or LAN2 port
<auto>: auto-negotiation mode
<10h/10f/100h/100f>: 10/100Mbps, half/full-duplex mode
Display or set up IGMP v2 snooping configuration
<on/off>: enable or disable built-in IGMP v2 snooping function,
default is off
<Query
no IGMP query frame received from the router, default is
seconds (range from 4 to 510 in even)
Display or set up the QoS configuration, include priority queue,
<weight>]
service weight and discard ratio while congestion, refer
for more.
<queue>: select queue index (0~3) to configure, as q0(lowest
priority)/q1/q2/q3(highest priority)
<weight>: assign the queue with service weight(1~15), default
1
for q0,
<discard
utilization, default
1 for 25%, 2 for 50% and 3 for 75%. refer
Display or set up the LAN1/LAN2 maximum rate. refer
Bandwidth Control
<lan1/lan2>: configure LAN1 or LAN2 port
<tx/rx>: direction, incoming(rx) or outgoing(tx)
<on/off>: enable or disable control on this direction
<N>: the setup max rate (multiply value by 64kbps). Range
from 0 to 1563, bandwidth control is invalid if N >= 1563
Display or set up the QoS configuration for TCP/UDP traffic
classification, to assign higher priority for total 8 different
TCP/UDP protocols
<queue>] ]
<set>: rule set index, at most 8 set (0~7)
<act/deact>: activate or de-activate this set
<port>: TCP/UDP port number (0~65535),
<queue>: select queue index (0~3) for this rule set, as
q0(lowest priority)/q1/q2/q3(highest priority)
Display or set up the static MAC entry, total 8 entries of MAC
time>: query SNTP server period, default
zone>: '+hh:mm' or '-hh:mm' to GMT time,
mm
for minutes, default '+00:00'
Interval>: expiry timer to age learned Multicast MAC if
2
for q1,
3
for q2 and
mode>: choose the discard mode(0~3) for queue
0
for 0%.
for more.
38
<ip>
162
on
System
Time.
60
minutes
hh
for hours
Priority
4
for q3
Priority
for more.
248
Advertisement
Table of Contents
