Table of Contents
Advertisement
DYNAMIX HP-51M Coax MDU Master Bridge User's Guide
dir
[-s
<pri/sec> <ip>]
dns
exit
quit
[-c
<hostcnt>]
[-n
<note>]
[-u
<uprate index>]
ep
<mac>
ephpnareboot
-m
<mac>
(Smart EP)
-m
<mac>
epstat
[-r]
(Smart EP)
-m
<mac>
[-t]
[-u]
[-r]
[-d]
[-p
<lan1/lan2/hpna>
[-l
<up/down>]
epswc
[-s
<auto /10h /10f
(Smart EP)
/100h /100f>]
[-f
<on/off>]]
epswigmp
-m
<mac>
epswqosq
epswqosrate
epswqostc
epswtagvlan
(Smart EP)
[-s
<set>
[-c
<act/deact>]
[-a
<ip>
[-t
<allow/deny>]
filter
[-w
[-n
<allow/deny>]
[-p
<allow/deny>] ]
help
Show detail file information resides in flash ROM. Include
'Working Area' and 'Upload Area', refer
filenames are,
'bootcode': boot loader
'sysfw4m': system firmware
'G1C28H21M': Master HCNA driver
'G0C28H20Ep': 3010 EP HCNA driver
'G1C28H21Ep': 3110 EP HCNA driver
'diagsw': 3010 diagnosis utility file
'diagsw1': 3110 diagnosis utility file
Accompanying with file id, file version, file date, and file size.
Display or set up DNS server setting.
-s
pri
<ip>: set up Primary DNS server's IP
-s
sec
Close the Telnet console.
Close the Telnet console.
Set up the EP
<hostcnt>: EP
<note>: EP
<uprate
*64Kbps), default
<mac>: designated EP MAC to configure
Reset remote Smart EP device
Display remote Smart EP port statistics for port
LAN1/LAN2/HCNA.
-r: reset all port statistics counter to 0
Display or set up remote Smart EP built-in switch Ethernet
properties
-t: display EP switch settings
-u: display EP switch/port status
-r: reset EP switch
-d: reset EP switch's eeprom settings to factory default
-p: configure EP port LAN1/LAN2/HCNA
-l: link, <up/down>: force current port to link up or down, i.e.
enable/disable current port
-s: current port Ethernet mode setting,
<auto>: auto-negotiation mode
<10h/10f/100h/100f>: 10/100Mbps, half/full-duplex mode
-f: current port Ethernet flow-control setting,
<on/off>: turn on /off flow control
Refer swigmp, swqosq, swqosrate, swqostc,
same functionality, but operate on remote Smart EP with
designated MAC address
Display or set up the filter rule set, refer the section
Source" for IP
-m
<mask>]
<set>: filter set index, total 16 set (0~15)
<act/deact>: activate or de-activate the rule set
<allow/deny>]
<allow/deny>: allow or deny the protocol
-t: telnet
-w: http/web
-n: snmp
-p: reply to ICMP ping
Display all commands with brief description
<ip>: set up Secondary DNS server's IP
Properties Profile
Host Limit
setting value (0~255), default
Note
setting value
index>: EP
Upstream Rate
0
for unlimited
<mac>
<ip>
and Subnet Mask setup <mask>.
36
Figure
4. The listed
related setting values.
255
setting value ( 0~1563,
swtagvlan
for the
"Allow
Advertisement
Table of Contents
