Download Print this page
Curtis TCTS/T Service Manual
Hide thumbs Also See for TCTS/T:

Advertisement

Quick Links

Models Included:
CAUTION:
must be installed to
comply with applicable
federal, state, and local plumbing/
electrical codes having jurisdiction.
CAUTION: Follow this
setup procedure before
attempting to use this
unit. Failure to follow these instruc-
tions can result in injury and/or void
of warranty.
CAUTION: DO NOT
connect the unit to hot
water. The inlet valve is
not rated for hot water.
IMPORTANT:
After setup, run a FULL
brewcycle. Place a tea
container to catch both hot water
from the brewcone and dilution water
from spout on the front cover.
WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.
ISO 9001:2008 REGISTERED
WILBUR CURTIS CO.
Montebello, CA 90640
For the latest information go to
www.wilburcurtis.com
Tel: 800/421-6150
W
Service Manual – TCT & PTT
Important Safeguards/Symbols
This appliance is designed for commercial use. Any servicing other than cleaning and preventive maintenance should be performed by an
Symbols
WARNINGS – To help avoid personal injury
Important Notes/Cautions – from the factory
Sanitation Requirements
The Curtis G3 Brewer is Factory Pre-Set and Ready to Go... Right from the Box.
Following are the Factory Settings for the G3 Iced Tea Brewer.
Generally there will never be a reason to change the G3/Gold Cup Series default settings. However, should you need to make slight
adjustments to meet your brewing needs, programming instructions are provided later in this manual.
System Requirements:
SETUP STEPS
the brewer.
NSF International requires the following water connection:
cleaning underneath.
installed and maintained in accordance with federal, state, and local codes.
caused by an empty tank.
readout.
5. Important: Run one full brewcycle, to purge the water lines and valves of air. Five seconds of dilution water at the beginning of each
brewcycle is normal pre-programmed operating behavior.
BREWING INSTRUCTIONS
Pour leaf tea into basket.
C
C
ilbur
urtis
ompany
3. Slide brew cone into brew
rails. Place tea container
under brew cone.
, i
.
nC
brew tea.
1

Advertisement

loading

Summary of Contents for Curtis TCTS/T

  • Page 1 WARNINGS – To help avoid personal injury Important Notes/Cautions – from the factory Sanitation Requirements The Curtis G3 Brewer is Factory Pre-Set and Ready to Go… Right from the Box. Following are the Factory Settings for the G3 Iced Tea Brewer. Models Included: Generally there will never be a reason to change the G3/Gold Cup Series default settings.
  • Page 2: Program Menus

    Programming Your Curtis Generation 3 Brewer is Factory Pre-Set for Optimum Performance. After connection to water and power; the rear toggle switch must be on. You will hear a beep sound, indicating power is available to the controller. CURTIS CURTIS <...
  • Page 3 Programming Tea Dilution Stir (Factory set to ON). Tea Dilut Stir Press to Select. Press < or > buttons, to toggle between OFF and ON. Press to set. Tea Pulse Brew (Factory set to OFF). Press to Select. Press < or > to select ON, OFF or D. D is a manual adjust from 1 to 20 pulses with an ON time Tea Pulse Brew from 5 to 150 seconds and an OFF time from 5 to 150 seconds.
  • Page 4: Error Message

    Programming Banner Name (Factory set to CURTIS) Banner Name Press to display letters and change letters or < to move place and EX to exit when complete This feature allows up to 14 letters to be programmed for company name or regional name. Programming all blanks disables Banner Name.
  • Page 5 Illustrated Parts TCT...
  • Page 6: Parts List

    PARTS LIST PART Nº...
  • Page 7 Illustrated Parts List...
  • Page 8 Illustrated Parts List...
  • Page 9 TCT ELECTRICAL SCHEMATIC...
  • Page 10 1. Store tea bags in a dark, cool and dry place away from strong odors and moisture. Do not refrigerate. TEA TIPS tea after eight hours WARNING DO NOT 3. Brew only enough tea that you reasonably expect to serve within a few hours. refrigerate unused tea overnight for later storage and dispensing equipment at least once a day.
  • Page 11 TCT ROUGH-IN DRAWING PTT ROUGH-IN DRAWING...
  • Page 12 WILBUR CURTIS CO., INC. 6913 Acco St., Montebello, CA 90640-5403 USA Phone: 800/421-6150 Fax: 323-837-2410 Technical Support Phone: 800/995-0417 (M-F 5:30A - 4:00P PST) E-Mail: techsupport@wilburcurtis.com Web Site: www.wilburcurtis.com FOR THE LATEST SPECIFICATION INFORMATION GO TO WWW.WILBURCURTIS.COM Printed in U.S.A. 12/2012...

This manual is also suitable for:

Ptt3