Panasonic PT-SRQ35KC Operating Instructions Manual page 299

Control command
The following table lists the commands that can be used to control the projector using a computer.
r Projector control command
Command Details
PON Power on
POF Power standby
QPW Power query
Switching the input
IIS
signal
OSH Shutter control
QSH Shutter status query
VSE Aspect ratio switch
Aspect ratio settings
QSE
query
OCS Sub memory switch
Sub memory status
QSB
query
*1 This can be used when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10C) is installed in <SLOT 1>.
*2 This can be used when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10C) is installed in <SLOT 2>.
*3 This can be used when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*4 This can be used when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
r Lens control command
Command Sub command
VXX LNSI2
VXX LNSI3
VXX LNSI4
VXX LNSI5
Chapter 7 Appendix — Technical information
Parameter/response
string
— To check if the power is on, use the "Power query" command.
000 STANDBY
001 Power on
HD1 HDMI
DL1 DIGITAL LINK
AU1,SD1 SDI1 [SLOT1]
*1
AU1,SD2 SDI2 [SLOT1]
*1
AU1,SD3 SDI3 [SLOT1]
*1
AU1,SD4 SDI4 [SLOT1]
*1
AU2,SD1 SDI1 [SLOT2]
*2
AU2,SD2 SDI2 [SLOT2]
*2
AU2,SD3 SDI3 [SLOT2]
*2
AU2,SD4 SDI4 [SLOT2]
*2
AU1,HD1 HDMI1 [SLOT1]
*3
AU1,HD2 HDMI2 [SLOT1]
*3
AU2,HD3 HDMI3 [SLOT2]
*4
AU2,HD4 HDMI4 [SLOT2]
*4
AU1,DV1 DVI-D1 [SLOT1]
*3
AU1,DV2 DVI-D2 [SLOT1]
*3
AU2,DV3 DVI-D3 [SLOT2]
*4
AU2,DV4 DVI-D4 [SLOT2]
*4
AU1,DP1 DisplayPort1 [SLOT1]
*3
AU1,DP2 DisplayPort2 [SLOT1]
*3
AU2,DP3 DisplayPort3 [SLOT2]
*4
AU2,DP4 DisplayPort4 [SLOT2]
*4
AU1,OP1 SDI OPT1 [SLOT1]
*3
AU1,OP2 SDI OPT2 [SLOT1]
*3
AU2,OP1 SDI OPT1 [SLOT2]
*4
AU2,OP2 SDI OPT2 [SLOT2]
*4
0 Opened
1 Closed
0 DEFAULT
1 4:3
2 16:9
5 THROUGH
6 HV FIT
9 H FIT
10 V FIT
01 - 96 Sub memory number
Details
Lens H shift
+00000 = Fine adjustment 1+, +00001 = Fine adjustment 1-, +00100
Lens V shift
= Fine adjustment 2+, +00101 = Fine adjustment 2-, +00200 = Coarse
Lens focus
adjustment+, +00201 = Coarse adjustment-
Lens zoom
Remark (parameter)
Remark
ENGLISH - 299