Table of Contents
Advertisement
[COMMAND]
[INPUT]
[OPERATING MODE]
*1 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10C) is installed in <SLOT 1>.
*4 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10C) is installed in <SLOT 2>.
*5 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100C) is connected to the projector, its input name is
automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*6 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
11) Press the <执行> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <菜单> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <执行> button.
Note
f To delete a command that has been already set, press the <默认> button on the remote control while the screen in Step 5) is displayed, or
select [DELETE] at the screen in Step 6) and press the <执行> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 186)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
[HDMI]
[DIGITAL LINK]
[HDMI1 [SLOT1]]
[HDMI2 [SLOT1]]
[HDMI3 [SLOT2]]
[HDMI4 [SLOT2]]
[DVI-D1 [SLOT1]]
[DVI-D2 [SLOT1]]
[DVI-D3 [SLOT2]]
[DVI-D4 [SLOT2]]
[DisplayPort1 [SLOT1]]
[DisplayPort2 [SLOT1]]
[DisplayPort3 [SLOT2]]
[DisplayPort4 [SLOT2]]
[SDI1 [SLOT1]]
*1
[SDI2 [SLOT1]]
*1
[SDI3 [SLOT1]]
*3
[SDI4 [SLOT1]]
*3
[SDI1 [SLOT2]]
*4
[SDI2 [SLOT2]]
*4
[SDI3 [SLOT2]]
*2
[SDI4 [SLOT2]]
*2
[SDI OPT1 [SLOT1]]
[SDI OPT2 [SLOT1]]
[SDI OPT1 [SLOT2]]
[SDI OPT2 [SLOT2]]
[INPUT1] - [INPUT10]
[NORMAL]
[ECO]
[QUIET]
*6
[USER1]
[USER2]
[USER3]
Switches the input to HDMI.
Switches the input to DIGITAL LINK.
Switches the input to HDMI1 of the Interface Board.
*1
Switches the input to HDMI2 of the Interface Board.
*1
Switches the input to HDMI3 of the Interface Board.
*2
Switches the input to HDMI4 of the Interface Board.
*2
Switches the input to DVI-D1 of the Interface Board.
*1
Switches the input to DVI-D2 of the Interface Board.
*1
Switches the input to DVI-D3 of the Interface Board.
*2
Switches the input to DVI-D4 of the Interface Board.
*2
Switches the input to DisplayPort1 of the Interface Board.
*1
Switches the input to DisplayPort2 of the Interface Board.
*1
Switches the input to DisplayPort3 of the Interface Board.
*2
Switches the input to DisplayPort4 of the Interface Board.
*2
Switches the input to SDI1 of the Interface Board.
Switches the input to SDI2 of the Interface Board.
Switches the input to SDI3 of the Interface Board.
Switches the input to SDI4 of the Interface Board.
Switches the input to SDI1 of the Interface Board.
Switches the input to SDI2 of the Interface Board.
Switches the input to SDI3 of the Interface Board.
Switches the input to SDI4 of the Interface Board.
Switches the input to SDI OPT1 of the Interface Board.
*1
Switches the input to SDI OPT2 of the Interface Board.
*1
Switches the input to SDI OPT1 of the Interface Board.
*2
Switches the input to SDI OPT2 of the Interface Board.
*2
Switches the input to DIGITAL LINK, and switches the input of the
*5
DIGITAL LINK output supported device to the specified input.
Prioritizes brightness.
Prioritizes the life of the light source.
Prioritizes the operation with low noise.
Controls the power with the setting set to [USER1].
Controls the power with the setting set to [USER2].
Controls the power with the setting set to [USER3].
Description
ENGLISH - 189
Advertisement
Table of Contents
