Table of Contents
Advertisement
Quick Links
Installation, Operation and Maintenance
Owner's Manual
SC200-DWS10
Manufactured in Canada by:
425 Clair Rd. W, Guelph, Ontario, Canada N1L 1R1
t. (+1) 519.763.1032 • tf. 1.800.265.7246 (US and Canada only)
t. +31 73 747 0144 (Europe only) • f. (+1) 519.763.5069
e-mail: info@viqua.com
www.viqua.com
520190-R_RevA
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Viqua Sterilight Cobalt SC200-DWS10
Summary of Contents for Viqua Sterilight Cobalt SC200-DWS10
- Page 1 Owner’s Manual SC200-DWS10 Manufactured in Canada by: 425 Clair Rd. W, Guelph, Ontario, Canada N1L 1R1 t. (+1) 519.763.1032 • tf. 1.800.265.7246 (US and Canada only) t. +31 73 747 0144 (Europe only) • f. (+1) 519.763.5069 e-mail: info@viqua.com www.viqua.com 520190-R_RevA...
- Page 2 WATER CONFIDENCE Each component of your VIQUA system has been designed and developed through extensive research and development to be part of an overall system that operates safely and efficiently over its entire lifetime.
- Page 3 Congratulations , you have just purchased the Sterilight Cobalt™ ® drinking water system. By purchasing this device, you have taken the first step in ensuring the safety of your water supply by using a totally non-intrusive, physical disinfection method. Your Sterilight system uses the most advanced UV technology on the market and is designed to provide you with...
-
Page 4: Table Of Contents
Table of Contents: Parts / Schematic Breakdown Safety Instructions Water Chemistry Installing Your UV Disinfection System Disinfection Procedure Operating and Maintenance Instructions Operation Troubleshooting 11-12 Dose Flow Chart Specifications Manufacture’s Warranty 14-15 *CSA/UL certification with approved power cord and lamps only. Potential Safety Measures Hazard... - Page 5 Symbols: Protective Caution Ground Electrical Fragile Warning WEEE (waste electrical or Eye Protection electronic equipment)* * This symbol indicates that you should not discard wasted electrical or elec- tronic equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
-
Page 6: Parts / Schematic Breakdown
System Components: Hard glass, coated Sterilume ®- HO UV lamps for long, consistent life (9000 hours) S200RL -HO Controller lamp connector POWER - 100-240V/50-60HZ 214 fused quartz sleeves retaining clip with fire polished ends BA-ICE-C COBALT SYSTEM QS-200 gland nut RN-001 bracket 420589-R... -
Page 7: Safety Instructions
Safety Instructions: WARNING - Always shut-off water flow and release water pressure before servicing. WARNING - to guard against injury, basic safety precautions should be observed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. CAUTION - Always disconnect power before servicing. DANGER - To avoid possible electric shock, special care should be taken since water is present near electrical equipment. -
Page 8: Water Chemistry
Water Chemistry: Water quality is extremely important for the optimum performance of your UV disinfection system. The following levels are recommended for installation: • Iron: < 0.3 ppm (0.3 mg/L) • Hardness*: < 7 gpg (120 mg/L) • Turbidity: < 1 NTU •... - Page 9 SC200-DWS10 Sterilight-DWS this document. If the water is to be consumed while the system is off-line, the water must be boiled for two minutes prior to consumption. Select a suitable location for the disinfection system and its related components. As it is recommended to install a ground fault protected circuit (GFCI), make sure that this is taken into consideration prior to any installation.
- Page 10 Once it is determined that there are no leaks, plug the system into the ground fault interrupter, and check controller to ensure the system is operating properly. The controller is designed to detect both power to the system and lamp illumination. It is important to NEVER LOOK DIRECTLY AT THE GLOWING UV LAMP .
-
Page 11: Disinfection Procedure
Disinfection Procedure: UV disinfection is a physical process and does not add any potentially harmful chemicals to the water. As UV does not provide a disinfection residual, it is imperative that the entire distribution system located after the UV be chemically disinfected to ensure that the water is free from any bacteriological contaminants. -
Page 12: Operating And Maintenance Instructions
OPERATION • Always disconnect power before performing any work on the disinfection system. • Regularly inspect your disinfection system to ensure that the power indicators are on and no alarms are present. • Replace the UV lamp annually (or biennially if seasonal home use) to ensure maximum disinfection. - Page 13 body of the connector in order that the connector may slide fully over the retaining nut. Once the connector is located fully over the retaining nut, slide the metal ring back in to lock the connector in place (Figure 2E). As this connector is keyed to the reactor chamber, make sure the notch on the connector (Figure 2D) is located over the ground lug located on the reactor chamber.
- Page 14 Cartridge replacement: It is recommended to change the filter cartridge every six months (or earlier). A gradual drop in water pressure after the filtration device is an accurate method of determining that the pre-filter cartridge is nearing the end of its life! To change the cartridge, please follow the following procedure: Note: Prior to performing any work on the drinking water system, ALWAYS DISCONNECT THE POWER SUPPLY FIRST.
-
Page 15: Operation
Operation: Controller: 1. Lamp life remaining (days): The controller tracks the number of days of operation of the lamp and the controller. The default screen will display the total lamp life remaining (in days). The controller will count down the number of days remaining until the lamp requires changing (365 days to 1 day). At “0”... -
Page 16: Troubleshooting
Troubleshooting: TROUBLESHOOTING GUIDE Symptom Possible Causes Solutions • replace filter cartridge with appropriate 5 micron cartridge Pressure Drop Sediment filter clogged Note: check source water supply as fluctuations may occur in source pressure • clean sleeve with scale cleaner and eliminate Quartz sleeve is stained source of staining problem (ie. -
Page 17: Dose Flow Chart
DISPLAY FAULT MODES LED display reads • lamp life expired - countdown is at “0” days “A3” • press reset button for a deferred alarm, replace UV lamp • controller is in lamp failure mode • power system down, allowing it to reset itself; apply power in order to LED display is blank confirm that the controller is able to power lamp... -
Page 18: Specifications
Specifications: MODEL SC200-DWS10 56.8 lpm US Public Health (15 gpm) 16mJ/cm (3.4 m /hr) 30.3 lpm VIQUA Standard (8 gpm) 30 mJ/cm (1.8 m /hr) 22.7 lpm NSF/EPA (6 gpm) 40mJ/cm (1.4 m /hr) Overall Dimensions 17”x 10.5” x 17 .8 (width x Depth x Height) 1“... -
Page 19: Manufacture's Warranty
(2) years from the date of purchase. During this time, VIQUA will repair or replace, at its option, any defective parts covered by the warranty. Please return the defective part to your dealer who will process your claim. - Page 20 VIQUA does not assume any liability for personal injury or property damage caused by the use or misuse of any of the above products. VIQUA shall not in any event be liable for special, incidental, indirect or consequential damages. VIQUA’s liability shall, in all instances, be limited to repair or replacement of the defective product or part and this liability will terminate upon expiration of the applicable warranty period.
Need help?
Do you have a question about the Sterilight Cobalt SC200-DWS10 and is the answer not in the manual?
Questions and answers