Table of Contents
Advertisement
Specifications
Input Voltage:
6R series:
220 to 460Vac
6R15-80: 380Vac to 415Vac
Input Frequency:
50 / 60Hz +/- 3Hz,
Auto detecting
Control Supply:
24Vdc (+15%, -15%)
24VDC Power Supply (min. requirements):
Power Supply O/P:
24VDC Regulated
Peak power requirements:
6R15-30:
1.5 Amps (36W)
6R60-80:
2 Amps (48W)
6R100–220:
3.0Amps (72W)
6R300–880:
4.0 Amps (96W)
These ratings allow for peak current requirements of
internal fans
Configurations:
3 wire & 6 wire
Bypass or Continuous
6R15 to 6R80 have integral Bypass
Contactor.
Duty:
Light Duty:
300% for 15 secs; 10start/hr
Standard Duty:
300% for 40secs; 10start/hr
400% for 10 secs;10start/hr
Severe Duty:
450 for 20 secs; 5start/hr
300% for 60 secs; 5start/hr
SCR PIV:
Minimum 1400V
SCR configuration:
Full-wave
Dv/dt suppression:
RC snubber networks
Over Voltage:
MOV
Rated Insulation:
2Kv
EMC
Class A (to AS61800 – C-tick)
Current Feedback
Current transformer in circuit
at all times.
Control
Torque controlled Ramp or
voltage ramp, with current limit
override
Standards Compliance
AS31800 C-tick; AS3947.4.2,
IEC60947-4-2
Environment:
Enclosure protection:
IP00 – IP20
Operating Temp.
0 to 55°C
(derate by 1% / °C >40°C)
Cooling:
Temperature controlled forced
ventilated
Maximum Altitude:
1000m without derating
Operating position:
Vertical
Maximum ambient
Pollution:
Degree 3 conforming to
IEC947-4-2
Inputs:
Digital Inputs:
24Vdc logic
Function :
2x Programmable inputs
1x Enable Input
Technical Manual: Smartstart
®
6000
Page 28
Thermistor:
Thermistor or NC switch
PTC type, Trip Resistance 3000Ohms,
<20ohms detected as Short Circuit.
Outputs:
Digital Output:
4 Programmable Relays
Contact Rating:
5A 250Vac; 5A 30VDC
Analogue Output:
1x Programmable Output
Signal:
0-10V, 0-5V, 4-20mA
Communications: Modbus RS485 with Ethernet Option
(Available in later revision)
Protection:
Motor Overload
Adjustable; Class 10, 10A, 20, 25, 30
type R1, total memory function
SCR Over temp.
Heat sink temperature
SCR protection:
Currrent & thermal modelling
Under Current
Adjustable level and trip time
Over Current
Adjustable level and trip time
Under Torque:
Adjustable level and trip time
Over Torque:
Adjustable level and trip time
Motor Stalled
300% for 3 seconds (run mode only)
Current limit
Adjustable
Starter Overload
Current & thermal modelling
O/P Short Circuit
Semiconductor fuses (optional)
Voltage imbalance
Input voltage imbalance
Current Imbalance
Input & output current imbalance
Bypass failure
No bypass after ramp time or during
run mode
SCR fault
Open or Short circuit SCR
Acc over time
Accel time exceeds set time
Phase reversal
Phase rotation inhibit
Motor Loss
Motor or output open cct
CT fault
Fault with CT's
Human Interface Module (HIM):
Type:
Local or remote mountable (IP66)
Display:
Backlit LCD (Blue) , English
Menu:
Coded & English
Menu Protected:
Selectable user access code
Cable type:
Ribbon or Cat-5
Essential Services Over-ride (ESO):
Selectable Digital input with 24Vdc logic.
Battery:
Type:
CR1220
IMI0042 rev D
Advertisement
Table of Contents
