Related Manuals for AirCom A16 Series
Summary of Contents for AirCom A16 Series
- Page 1 AIRLESS SPRAY GUNS A16 series Instruction manual mod. A16, A16 double entry aircom.it...
-
Page 2: Available Models
AVAILABLE MODELS mod. A16 It allows to obtain uniform painted surfaces mod. A16 double entry It allows to obtain uniform painted surfaces, with double entry AIRCOM - INSTRUCTION MANUAL - 2022 - v. 1.0 ®... - Page 3 A16 series Index Instruction Manual Warnings Maintenance and cleaning Installation and start-up Technical data Troubleshooting Spare parts and components Disposal Support WARNINGS! Carefully read and follow all instructions and safety precautions before using the product. MANUALS Our manuals are available at aircom.it/en/support/manuals/...
-
Page 4: Health Hazard
A16 series WARNINGS CORROSIVE PRODUCTS HEALTH HAZARD Solvents such as trichlorethane and Some sprayed chemicals can be harmful chloromethylene (dichlorethane) can and cause irritation or health problems. chemically react with the aluminum that Careful reading labels makes up much of the gun and cause instructions for use of the product is dangerous explosions. -
Page 5: Installation
A16 series INSTALLATION TECHNICAL SPECIFICATIONS Gun size: see dimensioned views Usage The gun must be supplied with a maximum pressure of 250 bar. aircom.it Instruction Manual - 5... - Page 6 A16 series INSTALLATION AND STARTUP Before using a new gun or a new product, clean the gun thoroughly with an appropriate solvent. Powering should be done with dry, filtered air and regulated to constant pressure. DIRECTIONS FOR GUN OPERATION Pipe Ø 6 ÷ 8 Product inlet Pipe Ø...
-
Page 7: Adjustment Sequence
A16 series ADJUSTMENT SEQUENCE Connect the paint inlet hose to the gun connection (1). Select the most suitable nozzle according to the job to be performed. Connect the air (which allows you to start or stop the delivery of the product) to the gun connection (2). -
Page 8: Technical Data
A16 series TECHNICAL DATA SPRAY NOZZLE ORIFICE PRODUCTS ANGLE AT 30 CM 7x20 20° 0,15 13,5 7x40 40° 0,15 16,5 TRANSPARENT AND PIGMENTED PAINTS 9x20 20° 0,23 FINE ENAMELS 9x40 40° 0,23 17,5 9x60 20° 0,23 22,5 11x10 10° 0,28 11x20 20°... - Page 9 A16 series TECHNICAL DATA SPRAY NOZZLE ORIFICE PRODUCTS ANGLE AT 30 CM 21x10 10° 0,53 13,5 21x20 20° 0,53 18,5 21x40 40° 0,53 21,5 21x60 60° 0,53 32,5 26x10 10° 0,66 15,5 26x20 20° 0,66 THIXOTROPIC SPRAY FILLER FILLED BASES 26x40 40°...
-
Page 10: Troubleshooting
A16 series TROUBLESHOOTING Anomaly Problem / Solution No atomization No pressure reaches the gun Check the air system Dirty or worn nozzle Carefully clean the dirty nozzle. Replace nozzle if worn. There is more product than necessary. Reduce the passage of the product... - Page 11 AIRLESS SPRAY GUNS A16 series mod. A16, A16 double entry Spare parts and components aircom.it...
-
Page 12: Spare Parts
A16 series SPARE PARTS mod. A16 DETAILS LIST [x1] Finger protection [x1] 2-hole sleeve [x1] 1-hole sleeve [x1] Awl kit [x1] Body group [x1] Gasket [x1] Gasket [x1] Piston assembly [x1] Gasket [x1] Gasket [x1] Needle stroke adjustment unit [x1] Key 12 - Spare parts and components aircom.it... - Page 13 A16 series SPARE PARTS mod. A16 double entry DETAILS LIST [x1] Finger protection [x1] 2-hole sleeve [x1] 1-hole sleeve [x1] Awl kit [x1] Body group [x1] Gasket [x1] Gasket [x1] Piston assembly [x1] Gasket [x1] Gasket [x1] Needle stroke adjustment unit...
- Page 14 A16 series DISPOSAL If, for any reason, it is intended to put the painting unit out of service, it is necessary to observe some fundamental rules aimed at safeguarding the environment as per the provisions of the law currently in force.
- Page 15 AIRCOM SRL © 2022 - ALL RIGHTS RESERVED...
- Page 16 DISCOVER ALL PRODUCTS Follow us aircom.it...
Need help?
Do you have a question about the A16 Series and is the answer not in the manual?
Questions and answers