Miele PRI 210 Operating Instructions Manual
Commercial flatwork ironer
Hide thumbs
Also See for PRI 210:
- Operating instructions manual (188 pages) ,
- Operating instructions manual (35 pages) ,
- Operating instructions manual (40 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele PRI 210
Summary of Contents for Miele PRI 210
- Page 1 Operating instructions Commercial flatwork ironer PRI 210 PRI 214 PRI 217 To avoid the risk of accidents or damage to the en-AU, NZ appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 11 942 100...
-
Page 2: Table Of Contents
Contents Caring for the environment .................... Warning and Safety instructions..................Correct application......................Technical and electrical safety ..................Use of the appliance ......................Using accessories ......................Notes on the use of this flatwork ironer ................Guide to the appliance ....................Touch display ........................Display symbols ........................ - Page 3 Using the cleaning cloth....................34 Starting the waxing programme ..................35 Roller padding ........................37 Removing the ironing cloth (only for steel-wool roller covering) ........37 Fitting the ironing cloth (only for steel-wool roller covering) ......... 37 Miele Professional Service ....................38...
-
Page 4: Caring For The Environment
Caring for the environment Disposal of the packing material The transport and protective packaging has been selected from materials which are environmentally friendly for disposal, and can normally be recycled. Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites. -
Page 5: Warning And Safety Instructions
If other persons are being shown how to operate the flatwork ironer, they must be given these important safety instructions and/or be made aware of them. Miele cannot be held liable for injury or damage caused by non-compliance with these instructions. -
Page 6: Use Of The Appliance
It is essential that this standard safety requirement is observed and regularly tested. If in any doubt, please have the electrical installation inspected by a qualified electrician. Miele cannot be held liable for damages arising from an absent or faulty earth connection. -
Page 7: Using Accessories
Warning and Safety instructions Using accessories Accessory parts may only be fitted when expressly approved by Miele. Using spare parts or accessories from other manufacturers will invalidate the warranty, and Miele cannot accept liability. Coin operated ironers must be anchored to the floor by the supporting feet to prevent the risk of the machine tipping. -
Page 8: Guide To The Appliance
Guide to the appliance Control panel (touch display) FlexControl foot switch Infeed table Pick-off bands Finger guard Height-adjustable screw feet Roller Plinth (optional) Heater plate with cover Laundry box Laundry outfeed table Option PRI 210 PRI 214 PRI 217 Swing out bar Flexible laundry feed Leaf-spring padding Plinth... -
Page 9: Touch Display
Guide to the appliance Touch display The sensors on the touch display can be activated by a light touch with the finger. When a sensor is pressed, it is highlighted with a bar underneath. ... - Page 10 Guide to the appliance Display in roller speed selection mode sensor sensor For switching the flatwork ironer on and For increasing the roller speed. off. sensor sensor For decreasing the roller speed. For pausing the ironing process.
-
Page 11: Display Symbols
°F The current temperature of the heater Display of ironing temperature in °C or plate is higher than the target °F. This can be altered by the Miele temperature. The temperature of the Professional Service Department. heater plate is lowered. -
Page 12: Finger Guard
A malfunctioning finger guard function can lead to serious injury. Shut down the flatwork ironer immediately. Contact Miele without delay. Ensure that the flatwork ironer is not put into operation by other persons and draw attention to the potential hazard. -
Page 13: Swing Out Bar
Guide to the appliance While the ironer is operating, do not use the finger guard intentionally to interrupt the ironing process. Always interrupt the ironing process by pressing the sensor. Swing out bar (for PRI 214 as an optional accessory) Ironed laundry can be placed over the swing out bar to prevent creasing. Flexible laundry feed for outfeed laundry removal (for PRI 217 as an optional accessory) The flexible laundry feed mechanism enables the ironed laundry to be fed through to the... -
Page 14: Using For The First Time
Using for the first time Cleaning and waxing the heater plate before first use It is essential to clean and wax the heater plate before it is used for the first time (see “Cleaning and care - Starting the waxing programme”). Clean the heater plate by passing the cleaning cloth offset through the ironer across the ... -
Page 15: Operation
Operation Preparing the laundry Residual moisture For a good result and optimum ironing performance, the laundry should have the following residual moisture levels, depending on model: PRI 214/217: 15–25% residual moisture PRI 210: 15% residual moisture The ideal residual moisture level depends on the composition of the fabric. -
Page 16: Ironing
Operation Danger of burning on the hot edge of the heater plate. Danger of burning on the edge of the hot heater plate! There is a warning sticker on the heater plate housing to warn of the danger of burning. Avoid touching the edges of the heater plate. -
Page 17: Changing The Value For A Temperature Selection Sensor
Operation Changing the Press the temperature selection sensor you want to change the value for a value for. temperature Keep it pressed in. The bar will light up underneath it and the current selection sensor temperature value will appear in the display. Press the ... -
Page 18: Setting The Ironer Speed
Operation Press the . sensor to call up the roller speed selection mode. Setting the ironer speed The button will be highlighted with a bar underneath. Press one of the three roller speed buttons. (e.g. button ) The selected roller speed button will be highlighted with a bar underneath, and the flatwork ironer will operate at the preset roller speed for this button. -
Page 19: Removal Of Ironed Laundry
The ironer can be switched on again by pressing the sensor. Standby mode is deactivated by default. Standby mode can be activated at service level by the Miele Professional Service Department. The time at which the ironer will switch to standby mode can be adjusted to a value between 1 and 30 minutes of non-... -
Page 20: Stopping Ironing
When the foot switch is released, the roller starts to turn again automatically. The ironing process can continue. The foot switch can also be configured by Miele Professional Service so that operating the foot switch ends Pause mode, engages the heater plate and makes the roller start turning. - Page 21 If the ironing process is paused during the run-on time, you must purchase more ironing time to restart the flatwork ironer. Miele Professional Service can change the duration of the run-on time to a value between 0–5 minutes. At the end of the run-on time, the heater plate disengages and the roller comes to a standstill.
-
Page 22: Installation And Planning Notes
Installation and planning notes Installation requirements The flatwork ironer may only be commissioned by Miele Professional Service or by a Miele authorised technician. The flatwork ironer must be installed in accordance with applicable regulations and standards. Local energy supplier regulations must also be observed. -
Page 23: Installation
Installation and planning notes Installation The flatwork ironer should be transported to the installation site using a forklift. Do not remove the packaging until right before commissioning. This ironer must be transported or lifted from the wooden frame only with the lateral mounting flaps fitted. Lift the machine off its wooden frame at the installation site. -
Page 24: Levelling The Machine
Floor anchoring Suitable anchoring material for the flatwork ironer is available as optional accessories from the Miele Professional Service Department. Alternatively, the clamps that secured the flatwork ironer to the transport pallet may be used to anchor the machine to the floor. -
Page 25: Electrical Connection
Installation and planning notes Electrical connection The electrical connection must be carried out by a qualified electrician who must ensure that all electrical work is carried out in accordance with applicable regulations and standards. In case of unfavourable mains conditions, the machine may lead to interfering voltage fluctuations. -
Page 26: Exhaust Ducting
- The connection for the exhaust air ducting for vapour extraction (optional for PRI 210) is located on the rear of the left side column and has a diameter of 70 mm (HT DN 70). -
Page 27: Substitute Pipe Lengths
Installation and planning notes Substitute pipe Substitute pipe length lengths Type of bend PRI 210 PRI 214 PRI 217 90° bend r = 2 d 0.25 m 45° bend r = 2 d 0.15 m 90° bend r = d 0.35 m... -
Page 28: Maximum Permissible Total Pipe Length
Installation and planning notes Maximum Minimum internal pipe diameter Maximum permissible total pipe length permissible total (metal pipes) (exhaust air) pipe length PRI 210 PRI 214 PRI 217 70 mm 80 mm 20 m 90 mm 32 m 100 mm... -
Page 29: Optional Accessories
Installation and planning notes Optional accessories Only use genuine Miele spare parts and accessories with this machine. Using spare parts or accessories from other manufacturers will invalidate the warranty, and Miele cannot accept liability. Plinth UG 1200 The machine can be raised 100 mm by fitting the optionally available plinth UG 1200. -
Page 30: Laundry Box For Pri 210
Installation and planning notes Laundry box for An optional laundry box is available for the PRI 210 flatwork ironer. PRI 210 The laundry box is for preparation/pre-sorting of laundry when operating the machine standing up. ② Flatwork ironer PRI 210 with laundry box fitted Laundry box Laundry outfeed table... -
Page 31: Notes
Notes Changing the temperature unit (°C / °F) The temperature unit can be changed from °C to °F by Miele Professional Service. Saving and loading favourites The following steps describe how to save and load the most frequently used combinations of ironing temperature and roller speed to the sensor. -
Page 32: Fault Messages
Control system fault If the fault message appears again, repeat the procedure or switch the ironer off and back on. If the fault persists, please call Miele Professional Service. In the event of a malfunction, please call Miele Professional Service. -
Page 33: Cleaning And Care
Regular heater plate maintenance is essential for protecting the roller drive and the roller cover. Please follow the notes in the Miele Ironing Handbook on ironing and cleaning and care. The heater plate must be waxed every time it is cleaned. Failure to do so can result in a considerable reduction of the lifespan of the flatwork ironer. -
Page 34: Using The Cleaning Cloth
Cleaning and care Using the cleaning cloth Use the Miele cleaning cloth for cleaning the heater plate. As the cleaning cloth is narrower than the heater plate, the entire plate cannot be cleaned in one go. It is necessary to feed the cleaning cloth through the ironer several times, gradually moving it down the width of the heater plate. -
Page 35: Starting The Waxing Programme
Cleaning and care The heater plate must be waxed after every cleaning process. You can then switch directly to the waxing programme by pressing the temperature selection sensor on the right or exit the cleaning programme by pressing and holding the ... - Page 36 Cleaning and care Fold the ironer waxing cloth. Start the waxing programme (see “Cleaning and care - Starting the waxing programme”). Feed in the ironer waxing cloth into the ironer with the rubber-coated side facing the roller. Feed the ironer waxing cloth multiple times into the ironer from the left or right side at the ...
-
Page 37: Roller Padding
The ironing cloth on the PRI 217 with leaf-spring padding must only be removed or replaced by the Miele Professional Service Department. If the ironing cloth is removed without authorisation or the aid of the Miele Professional Service Department, there is a risk of damaging the leaf-spring padding and the heater plate. -
Page 38: Miele Professional Service
Miele Professional Service In the event of a malfunction, please call Miele Professional Service. Miele will require the model and serial number [SN] of the flatwork ironer. - Page 40 Freemans Bay Auckland 1011 New Zealand Telephone: 0800 4 MIELE (0800 464 353) www.miele.com.au/professional sales@miele-professional.com.au Miele Global Headquarters: Miele & Cie. KG Carl-Miele-Straße 29, 33332 Gütersloh, Germany Alteration rights reserved / Publication date: 41.21 M.-Nr. 11 942 100 / 00 ...