Summary of Contents for Miele HM 21-140 Professional
Page 1
Operating instructions Rotary ironer HM 21-140 en - CA To avoid the risk of accidents or damage to the machine it is essential to read these instructions before installing, M.-Nr. 09 284 130 commissioning and using it for the first time.
A damaged ironer could be dangerous. If the connection cable is damaged, it must be replaced by a Miele service technician. To avoid the risk of accidents and damage to the ironer please read these...
Page 5
Accessory parts may only be fitted when carried out by a suitably qualified engineer. expressly approved by Miele. If spare parts or accessories from other Correct use manufacturers are used, this will invalidate...
Please do not therefore dispose of it with your general waste. Please dispose of it at your local community waste collection / recycling centre, or contact Miele for advice. Please ensure that it presents no danger to children whilst awaiting disposal. M.-Nr. 09 284 130...
Description of the operating controls 0 - I button Roller speed selector The roller speed is increased by turning the Pressing this button switches the machine speed selector clockwise and decreased by on or off. The indicator in the button lights up turning it anti-clockwise.
Page 9
Description of the operating controls Finger guard Foot pedal switch Functions The finger guard is a safety feature and should always be checked before using the Switch position 1 (not pressed down) Ironing ironer. Switch position 2 Pressing Warning. Switch position 3 Heater plate is withdrawn Do not reach between the heater plate and the rotating roller.
Page 10
Description of the operating controls Coin mechanism 1 = Coin slot After a coin or token has been inserted, the pre-set duration will light up in the display. 2 = Coin return button 3 = Coin return 4 = Display M.-Nr.
Preparing the laundry Condition of laundry For a good finish, the ideal residual moisture Important Before using the ironer you level is about 25%. should clean the heater plate by running a cloth through the entire width of the roller. Rinsing the laundry using hot water in the final rinse helps to reduce the residual Useful tips...
Operation Ironing Check that the finger guard is functioning properly. ^ Switch on the on-site mains switch. The finger guard is a safety feature which must be checked daily for proper functioning before the machine is used. ^ Press the 0 - I button. The indicator in the button will light up.
Page 13
Operation Material Symbol Temperature range 40 - 60°C ß Polyester / artificial silk temperature ßß Silk / wool Medium temperature ßßß Cottons / High linen temperature Rotary ironers with coin operated ^ Select the roller speed, depending on the mechanism: degree of dampness and the type of laundry to be ironed.
Page 14
Operation ^ Release the foot pedal once the item has been placed on the roller. The heater plate will engage. When feeding in thicker items of laundry it is important to avoid putting a strain on specific points of the roller/heater plate. Feed items into the ironer is such a way that that seams, waistbands etc.
Notes Preparation of the working area Emergency release if there is a power cut whilst ironing Setting up your working area in as practical and convenient way as possible will ensure If there is a power cut during ironing, to greater efficiency when ironing.
Page 16
Notes Protection of the motor and the roller cover Disengage the heater plate during pauses between ironing and when you have finished ironing. This helps prolong the life of the roller cover and protects the motor. It also helps to prolong the life of the machine.
Cleaning and care The ironer generally requires very little If the steel wool padding needs replacing, attention. this must be done by a Miele service technician. Cleaning the heater plate When re-covering the roller, the cover should be between 656 mm and 664 mm wide to...
Explanation of symbols on the data plate 1 Model 2 Serial number 3 Article number 4 Material number 5 Voltage/Frequency 6 Mains fuse rating 7 Drive motor 8 Drum data* 9 Drum diameter/Drum depth* 10 Spin speed* 11 Drum volume/laundry dry weight* 12 Kinetic energy* 13 Run-up time* 14 Braking time*...
To ensure optimum flow, the ducting should The rotary ironer must be commissioned be laid with as few bends as possible and all by a Miele service technician. connections and joins should be airtight. The connection point for the exhaust ducting...
Electrical connection Electrical connection Connection should be made via a suitable isolator which complies with local and This machine conforms to IEC 335-1 and national safety regulations and which is IEC 335-2-44. easily accesible for disconnecting the machine from the electricity supply. The electrical connection may only be Provision must be made on site to switch off carried out by a suitably qualified technician...