Evakit Hardware; Installation - Fujitsu F2MC-16L Series User Manual

AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
2.

EVAKIT Hardware

AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA

2.1. Installation

The installation of the evaluation board is straightforward.
A power supply, capable of supporting a fairly stable 7-8V DC and about 450 mA, is required.
Note, that the power connector must be '+' at the shield and '−' in the centre.
As a first step, make sure that the small switches located nearby the LEDs are in marked
position ON. Connect the power supply and check that the red Power LED (see fig. 1) remains
on and that the green RUNning-User LED and the red LED Displays light up briefly after
Monitor Reset has been pressed and released.
Evaluation Board View
+
5/3V Select
-
Power
Supply
JP41
JP24..21
JP39
Fig. 1: Evaluation board view
While pressing the User Reset button, the green RUNning-User LED should be on. After
releasing the User Reset button the LED Displays should light up again.
If these installation checks were successful, the power supply should then be unplugged and
the serial connection to a PC via the 9-pin RS232 cable established at the external port
(labelled at solder side of the board) before re-connection of the power supply.
Now, the LEDs should behave in the same manner. – If not, it is most likely that the DTR
signal of the serial connection, which is used as an external Monitor Reset control line is
activated for some reason.
© FUJITSU Mikroelektronik GmbH 1996
FUJITSU MB90675-Evaluation Board - User Manual
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
Terminal Reset
JP18
RS232 Interfaces
AAAA AAAA AAAA AAA AAAA
AAAA AAAA AAAA AAA AAAA
AAAA AAAA AAAA AAA AAAA
AAAA AAAA AAAA AAA AAAA
internal
AAAA AAAA AAAA AAA AAAA
AAAA AAAA AAAA AAA AAAA
AAAA AAAA AAAA AAA AAAA
AAAA AAAA AAAA AAA AAAA
AAAA
AAAA
MB90675
AAAA A AAAA
AAAA A A AAAA
AAAA AAAA
AAAA A A AAAA
AAAA AAAA
JP40 Reset
Monitor User
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
JP37
JP14
SW3
Ext.Break
Mode Switches
JP42
AAAA AAAA AAA
AAAA AAAA AAA
AAAA AAAA AAA
AAAA AAAA AAA
external
AAAA AAAA AAA
AAAA AAAA AAA
AAAA AAAA AAA
AAAA AAAA AAA
AA
AA AA
User RAM
AAA
AAA
User RAM
AAA
Monitor
EPROM
Monitor
AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA
EPROM
A AAAA AAAA AAAA AAAA
A A AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA
A A AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA
LED Displays JP38
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA
User
LED (red)
Power
LED (red)
RUN
LED (green)
AAAA AAAA A
AAAA AAAA A A
AAAA AAAA
AAAA AAAA A A
AAAA AAAA
AAAA AAAA A A
AAAA AAAA
- 7 -