Related Manuals for Fujitsu F2MC-8FX MB95390 Series
Summary of Contents for Fujitsu F2MC-8FX MB95390 Series
- Page 1 FUJITSU MICROELECTRONICS MCU-AN-500092-E-10 SUPPORT SYSTEM F²MC-8FX FAMILY 8-BIT MICROCONTROLLER MB95390 SERIES EV BOARD MB2146-441-E SETUP GUIDE...
- Page 2 EV Board MB2146-441-E User Manual V1.0 Revision History Revision History Date Author Change of Records 2010-04-21 Kevin Wang V1.0,new MCU-AN-500092-E-10 – Page 2...
-
Page 3: Preface
PREFACE Thank you for purchasing the F2MC-8FX Family EV board: MB2146-441-E. This product is an EV board for F2MC-8FX MB95390 Series MCU, which comes with MB2146-08-E (F2MC-8FX Family MB95390 Series BGM Adapter), MB2146-441-E, and F2MC-8L/8FX Family SOFTUNE Professional Pack Evaluation Version. -
Page 4: Revision History
EV Board MB2146-441-E Setup Guide PREFACE Caution of the Products Described in this Document The following precautions apply to the product described in this manual. Indicates a potentially hazardous situation which, if not avoided appropriately, WARNIN could result in death or serious injury and/or a fault in the user’s system. Electric shock, Before performing any operation described in this manual, turn off all the power supplies to the system. - Page 5 The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS semiconductor device; FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information.
-
Page 6: Table Of Contents
EV Board MB2146-441-E Setup Guide Contents Contents REVISION HISTORY ......................2 PREFACE ..........................1 Handling and Use ......................1 Notice on this Document ....................1 Caution of the Products Described in this Document ........... 2 CONTENTS .......................... 4 BGMA MANUAL ......................5 BGMA Overview ...................... -
Page 7: Bgma Manual
EV Board MB2146-441-E Setup Guide Chapter 1 BGMA Manual 1 BGMA Manual This chapter gives introduction on how to set up BGMA. 1.1 BGMA Overview Below is a close look of MB95390 Series BGMA. The part number is MB2146-08-E. It provides a debugging platform for the MB95390 Series MCU in a small size of 55.7mm (W) X127mm (D) X30mm (H). -
Page 8: Idc10 Interface Description
EV Board MB2146-441-E Setup Guide Chapter 1 BGMA Manual 1.3 IDC10 Interface Description Pin Number Pin Name Description UVCC Target MCU V Target MCU V RSTIN Target MCU reset input RSTOUT Target MCU reset output Reserved Reserved Reserved Target MCU debugging pin Reserved Reserved 1.4 BGMA USB Configuration... - Page 9 EV Board MB2146-441-E Setup Guide Chapter 1 BGMA Manual Select “Install from a list or specific location (Advanced)”, then click “Next”. Figure 1.4-2 Install BGMA in Windows (2) Select “…\Drivers” from the folder where SOFTUNE is installed, click “Next”. Figure 1.4-3 Install BGMA in Windows (3) Page 7...
-
Page 10: Led Description
EV Board MB2146-441-E Setup Guide Chapter 1 BGMA Manual Select “BGMA (MB2146-08)” as displayed below, and then click “Next”. Figure 1.4-4 Install BGMA in Windows (4) Windows will install the driver automatically. Click “Finish” after the driver has completed the installation normally. - Page 11 EV Board MB2146-441-E Setup Guide Chapter 1 BGMA Manual Second, plug IDC10 cable to the EV board (target MCU board), then turn on EV board. After that, check whether the power LED on the BGMA turns orange. Refer to Figure 1.4-2. Orange Figure 1.5-2 BGMA Power LED (2) Page 9...
-
Page 12: Ev Board Introduction
EV Board MB2146-441-E Setup Guide Chapter 2 EV Board Introduction 2 EV Board Introduction 2.1 EV Board Overview MB95390 Series EV board provides a user-friendly evaluation platform for the MB95390 Family microcontroller. MB95390H/390K MCU EV board PN is MB2146-441-E. Figure 2.1 is a close look of EV board. Connector Test pin Connector... -
Page 13: Function List
EV Board MB2146-441-E Setup Guide Chapter 2 EV Board Introduction 2.2 Function List The EV-board consists of a board and a sample firmware. The board provides a useful platform for using the MCU and its peripherals. It is a useful development platform together with a BGMA (PN: MB2146-08-E) and a SOFTUNE. -
Page 14: Ev Board Schematic
EV Board MB2146-441-E Setup Guide Chapter 2 EV Board Introduction 2.3 EV Board Schematic Page 12... -
Page 15: Hw Module Description
EV Board MB2146-441-E Setup Guide Chapter 2 EV Board Introduction 2.4 HW Module Description 2.4.1 Power Module Input external power supply from outside. Please read the following instructions before using. Output voltage: 5V Output Current: 500mA Connection: Power connector (DC IN) 2.4.2 BGMA Interface To start debugging using a BGMA, users can connect IDC10 socket from the BGMA to BGMA IF on an EV board before power on. -
Page 16: Development Platform Quick Start
EV Board MB2146-441-E Setup Guide Chapter 3 Development Platform Quick Start 3 Development Platform Quick Start 3.1 Tools Setup Sequence Start the debugging system in the following sequence: Connect a BGMA to the PC using a USB cable, confirm the LED on the BGMA is Green; Connect an EV board to BGMA IDC10 socket;... - Page 17 MCU-AN-500092-E-10 FUJITSU MICROELECTRONICS LIMITED • SUPPORT SYSTEM F2MC-8FX Family MB95390 Series EV Board MB2146-441-E SETUP GUIDE Apr. 2010 the first edition Published FUJITSU MICROELECTRONICS LIMITED...