Page 1
All the rights to this manual are reserved, especially reproduction, publication and translation rights. No portion of this manual may be reproduced by no means (photocopy, microfilm or other methods) without previous written authorization from ECLERIS. Neither can it be reproduced, multiplied or published through any electronic data processing form.
USER MANUAL – STROBOLED TABLE OF CONTENT SYMBOLS ..........................3 SAFETY INFORMATION ......................3 WARNINGS .......................... 3 DESCRIPTION......................... 4 INTENDED USE ........................4 INTENDED USER ........................ 5 DESCRIPTION & FUNCTIONING ..................5 3.3.1. PARAMETERS TO BE ASSESSED BY STROBOSCOPY ..........5 COMPONENTS ........................
2. SAFETY INFORMATION The contents of this guide describe the recommended procedures for the proper installation and use of StroboLED. It contains all the necessary information for the appropriate care and use of the StroboLED. Please read the whole guide carefully before using the equipment.
USER MANUAL – STROBOLED The StroboLED and its foot switch are built on an aluminum housing that is resistant to shock and corrosion. Is easy to clean and it does not produce adverse biological reactions. Do not use the device during thunderstorms.
Results monitoring For a proper use of StroboLED it is essential to know the basic functioning of the equipment. 3.3.1. PARAMETERS TO BE ASSESSED BY STROBOSCOPY It is essential to know the parameters that have to be evaluated by stroboscopy. The different parameters are briefly discussed below.
Aperture and closure glottal cycle. Different phase between upper and lower lips of vocal folds. 3.4 COMPONENTS StroboLED includes the following necessary components and elements. It is advised to identify and check their existence before proceeding with the installation. Main unit ...
Ensure that every part and accessory has been shipped. Setting up the StroboLED does not require qualified or experienced personnel. Carefully follow the instructions provided in this section.
6) Plug the contact microphone to the connector on the front of the unit (1). 7) If you use a video camera (Ecleris PROCAM), plug it into the video input connector (5) and follow the instructions provided in its User's Manual.
Do not use the device in an oxygen rich environment. All connections should be made before turning the equipment on. The StroboLED should only be used in places where the electrical installations meet the local regulations in effect. If before connecting the StroboLED any anomaly is detected, please contact the technical service department of your local distributor or the closest ECLERIS office, prior to its use.
Page 10
USER MANUAL – STROBOLED Press the Strobe settings button; it will take you to the microphone type selection screen, used for detecting the fundamental frequency during the laryngostroboscopy. Microphone Selection and the vocal cords velocity: Select the microphone to use clicking on the image. If you will be using the contact microphone supplied with the device, click on the image on the left.
USER MANUAL – STROBOLED Light Intensity: Light intensity setting in Continuous Mode. Level settings are 1-12. Press the red controls to increase or decrease the indicated level. This setting can only be done in Continuous Mode and not during the phonation process in any Mode.
MICROPHONE connector (2). Select the aerial microphone in the StroboLED settings for the device to detect the fundamental frequency from that microphone input (See the “Microphone Selection” section).
It is recommended to check the proper condition of the contact microphone. It can be damaged or cut, thus affecting the normal functioning of the equipment. Given that, request a replacement to your provider. ECLERIS is not liable for personal injuries or material damages caused to third-parties as a consequence of: ...
Oxide corrosion in connection pins. 7.3 FUSES REPLACEMENT To avoid time loss due to downtime of the StroboLED, it is recommended to have a spare fuse. 1) Disconnect the power supply cable from the electrical network and the equipment. Page 14 of 18...
3) Remove the burnt fuses and replace them with the spare fuses (2 x T3AL250V). Always have new spare fuses available to avoid loss of time and an inoperative unit. To avoid shock, injury, or damage to the StroboLED, use ONLY fuses with the same specified ratings (T3AL250V) 4) Place the fuses lid back pushing it until a “click”...
USER MANUAL – STROBOLED FREQUENCIES - WORKING MODE Automatic mode: 80-1500 Hz Working Range Manual mode: 80-1500 Hz 9. TROUBLESHOOTING The following table indicates the most frequent problems and their quick solutions. Please consult this table for any difficulty you may encounter.
If the problem cannot be solved, please contact your local distributor or the closest ECLERIS office and request technical service. TECHNICAL SERVICE The StroboLED must be repair and/or maintained exclusively by qualified personnel trained by ECLEIRS.
The warranty period is for one (1) year as from the date of purchase invoice. ECLERIS shall not be liable for any damage caused to/by the StroboLED due to incorrect use, negligence, cleaning or incorrect storage. Any repairs made by personnel not authorized by ECLERIS will void this warranty.
Need help?
Do you have a question about the STROBOLED and is the answer not in the manual?
Questions and answers