Page 1 EPSON PowerLite 8300i ® ® Multimedia Projector User’ s Guide...
Page 2: Important Safety Information
SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON product. EPSON is not responsible for any use of this information as applied to other products.
Page 3: Table Of Contents
Contents Welcome ........7 Using Your Documentation .
Page 4 Displaying and Adjusting the Image Projecting the Image....... 32 Troubleshooting Display Problems....35 Adjusting the Image .
Page 5 Fine-tuning the Projector Using the Menu System ......62 Restoring the Default Settings ....63 Adjusting the Image Quality.
Page 6 Cleaning and Replacing the Filters ....91 Replacing the Lamp ....... 94 Transporting the Projector .
Page 7: Welcome
Your projector includes these outstanding features: Connectivity Your EPSON PowerLite projector can be connected to four computer sources and five video sources (up to a total of six sources at the same time). You can include an independent sound channel for each of the six sources.
Page 8: Using Your Documentation
Built-in help system Provides assistance for common problems. Available from the button on the projector or the remote control. Help support.epson.com Download FAQs and e-mail your questions to EPSON support. ® Support card. Keep the...
Page 9: Registration And Warranty
Start Here kit for details. To register, simply fill out the registration card included in your Start Here kit and mail it to EPSON. Or you can register online at http://epsonwebreg.info2.net/. Registering also lets you receive special updates on new accessories, products, and service.
Page 10: Unpacking The Projector
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: Projector* Rear cable cover Projector software CD-ROM Remote control AA batteries Power cord Computer VGA cable Audio (stereo USB cable mini-jack) cable * Remove plastic film from projector’s control panel. Save all packaging in case you need to ship the projector.
Page 11: Additional Components
These cables are usually included with your video player; check the appropriate section in Chapter 1 to make sure of the kind of cable you need. You may be able to purchase it from EPSON (see page 12) or from your video dealer.
Page 12: Optional Accessories
Optional Accessories To enhance your use of the projector, EPSON provides the following optional accessories: Product Replacement lamp and air filter Air filter set EasyMP.net network option board Mounting hardware: Projection screens: Lenses: Cables: Macintosh adapter set (monitor and desktop adapter)
Page 13: Setting Up The Projector
Setting Up the Projector his chapter gives you basic information on setting up the projector: where to position it and how to connect it to a video source (such as a VCR or DVD player) or to a laptop or desktop computer. Follow the instructions in this chapter on: Positioning the projector Connecting to video equipment...
Page 14: Positioning The Projector
Positioning the Projector If you’re setting up the projector yourself note and it isn’t already installed in the theater You can mount the projector or conference room you’re using, you’ll on the ceiling, or place it probably want to place it on a table in front behind a translucent screen of the screen, as shown.
Page 15 After positioning the projector, you may want to connect a Kensington MicroSaver device to the lock port on the projector’s left side. You can purchase this from EPSON; see “Optional Accessories” on page 12 Ideal height button as Keystone Setting Up the Projector ®...
Page 16: Connecting To Video Equipment
Connecting to Video Equipment You can connect up to five video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video-output connections: RCA connector (composite video) S-video connector (4-pin mini-DIN) BNC connector (component video) Note that connecting a cable for RGB video provides the highest...
Page 17: Connecting A Composite Video Source
Connecting a Composite Video Source 1. Locate an RCA video cable (one is usually provided with your video equipment). 2. Connect the cable to the yellow video output connector on your player and the yellow Video 3. If you want to play sound through the projector, see page 29 for instructions on connecting an audio cable.
Page 18: Connecting An S-Video Source
3. If you want to play sound through the projector, see page 29 for 4. If you don’t need to make any other connections, see Chapter 2 Setting Up the Projector equipment, or you can purchase it from EPSON; see page 12). connector on the projector: S-Video instructions on connecting an audio cable.
Page 19: Connecting A Component Video Source
Connecting a Component Video Source 1. Locate a component video cable (one may be included with your video equipment). Look at the connectors at one end of the cable. If they are bayonet-style (BNC) connectors, continue on to the next step. If they are RCA connectors, you’ll need to attach commercially available BNC adapters to plug the cable into your projector.
Page 20: Connecting An Rgb Video Source
Connecting an RGB Video Source Follow these instructions to connect the projector to a video player that has an RGB video output port. Depending on the type of connector on your player, you’ll need to use the appropriate cable: Connecting Using a VGA Computer Cable 1.
Page 21 Connecting Using a BNC Cable 1. Locate a BNC video cable (one may be included with your video equipment). 2. Connect the cable to your player and the corresponding connectors on the projector. 3. If you want to play sound through the projector, see page 29 for instructions on connecting an audio cable.
Page 22: Connecting To A Computer
Connecting to a Computer You can connect the PowerLite projector to any computer that has a note standard VGA, BNC, or DVI-D (or DFP) dual-link monitor port, The projector accepts a wide including desktop models, PC notebook and laptop computers, range of resolutions and Macintosh PowerBooks and iBooks, and hand-held devices.
Page 23: Connecting To The Computer 1 Or 2 Port
If you’re using a PowerBook or an older Macintosh and you can’t connect the cable to your computer, you may need to use the Macintosh desktop adapter as shown on page 26 (available from EPSON; see page 12). Computer 1 Setting Up the Projector...
Page 24: Connecting To The Bnc Port
Connecting to the BNC Port 1. Depending on your computer’s connection, obtain the correct 2. Connect the cable to the projector’s note The connectors on your cable may be labelled, or they may be color-coded (black for H/C Sync and gray for V Sync).
Page 25: Connecting To The Dvi Port
Once the projector is turned on, be sure to select the source to see your image (see page 34). port as shown. Setting Up the Projector note An optional DVI to DFP cable is available from EPSON; see page 12.
Page 26: Using The Macintosh Desktop Adapter
If so, you’ll need to use a Macintosh desktop adapter to connect the VGA cable to your computer (available from EPSON; see page 12). 1. To use the adapter, remove its cover as 2.
Page 27: Connecting The Cable For Remote Mouse Control
Connecting the Cable for Remote Mouse Control If you’ve connected a computer as described in this chapter, you can use the projector’s remote control as a wireless mouse. This lets you control your computer and click through slideshow-style presentations, such as PowerPoint, from up to 30 feet away. To use the wireless mouse function, your system must have a USB port and one of these operating systems: Windows...
Page 28: Connecting An External Monitor
Connecting an External Monitor If you want to monitor your presentation close-up (on a monitor note placed beside the projector) as well as on the screen, you can connect The monitor can display images from any connected an external monitor. You can use it to check on your presentation or computer or video source.
Page 29: Playing Sound Through The Projector
Playing Sound Through the Projector You can play sound through the projector’s speaker system, or you can attach an external speaker system. (Attaching speakers to the projector instead of directly to the audio source lets you use the projector’s remote control to adjust the sound.) Connecting Audio Equipment to the Projector To play sound through the projector, follow these steps: 1.
Page 30: Connecting External Speakers
Connecting External Speakers To connect speakers to the projector, follow these steps: 1. Obtain the appropriate cable to connect your speakers. 2. Connect the stereo mini-jack end of the audio cable to the 3. Connect the other end of the cable to your speaker system. You The projector’s internal speaker system is disabled while sound is output to the external speakers.
Page 31: Displaying And Adjusting The Image
Displaying and Adjusting the Image hether you’re presenting from a computer or video equipment, or with the optional EasyMP.net, you need to follow some basic steps to display your image on the screen. Follow the guidelines in this chapter to: Turn on the projector and select the image source Adjust the image Shut down the projector...
Page 32: Projecting The Image
Projecting the Image Make sure your projector and other equipment are set up as described in Chapter 1. Then follow the instructions below to start the projector and display an image. Turning on the Projector If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source.
Page 33 3. Press the red P button on top of the projector—or press Power the P button on the remote control. Power (If this is your first time using the remote control, make sure the batteries are installed and the power switch on the side of the remote is turned on;...
Page 34: Selecting The Image Source
Selecting the Image Source Selecting the image source lets you switch between images input from note different pieces of equipment connected to the projector (such as a To focus and adjust the computer or DVD player), or turn on EasyMP.net if that option has image, see page 38.
Page 35: Troubleshooting Display Problems
Troubleshooting Display Problems Follow these guidelines if you’re having trouble displaying an image. You Can’t Project an Image If you see a blank screen or a blue screen with the try the following: Make sure the cables are connected correctly, as described in Chapter 1.
Page 36 If you're using Macintosh OS X: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select 2. Make sure the 3. Click the 4.
Page 37 If you’re using OS 8.6 to 9.x: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Monitors Monitors and Sound. 2.
Page 38: Adjusting The Image
Adjusting the Image Once you see your image, you need to make certain adjustments: If you want to fine-tune the image and/or sound, see Chapter 4. Focusing and Zooming Your Image Use the note sharpen the image. The Focus and Zoom buttons won’t work when Use the the wide-angle rear...
Page 39: Adjusting The Height Of Your Image
Adjusting the Height of Your Image If the image is too low on the screen, you can raise it using the Lens Shift. This is the best method for adjusting the height of the image. If you need to raise the image further, you can tilt the projector upward by extending the feet.
Page 40: Adjusting The Image Shape
2. Once the image is positioned where you want it, release the 3. If necessary, you can level the picture or fine-tune the height by Projector foot Raising the projector causes the image to distort or “keystone,” but you can manually correct the shape as described in the next section. Adjusting the Image Shape In most cases, you can maintain a square or rectangular image by placing the projector directly in front of the center of the screen and...
Page 41 Or press the button on the remote control, Menu select the menu, and press Setting the Setting menu, select Keystone . Then select Enter V-Keystone Adjust the setting as needed. When corrected, the image will be slightly shorter. If necessary, you can stretch the image to its proper size using the Height Using Quick Corner...
Page 42: Correcting Computer Images
Correcting Computer Images If you’ve connected a computer and the image doesn’t look right, or it doesn’t fit properly on the screen, press the remote control (or the control panel). This automatically resets the projector’s tracking, sync, resolution, and position settings. note You must be projecting an image for this button to have...
Page 43: Shutting Down The Projector
Shutting Down the Projector When you’ve finished using the projector, follow the recommended procedure to shut it down. This extends the life of the lamp and protects the projector from possible overheating. 1. If you’ve connected a computer or laptop, shut it down first; otherwise you may not be able to see your computer’s display to shut it down properly.
Page 44 Displaying and Adjusting the Image...
Page 45: Giving Your Presentation
Giving Your Presentation presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 30 feet away. You can use the remote control to adjust the picture and sound note (page 51), or as a pointer or drawing tool to highlight your For information and...
Page 46: Activating And Using The Remote Control
Activating and Using the Remote Control The remote control has an on/off switch on its side, as shown. Before using the remote, make sure batteries are installed as described on page 50, then push up on the on/off switch to turn it on. note If the pointer button is...
Page 47: Using The Navigation Buttons
Using the Navigation Buttons The remote control has various buttons that let you navigate the projector’s help and menu systems; they also let you use the drawing tools to highlight your presentation. If you’ve connected a computer, the buttons can be used in place of your computer’s mouse, letting you walk about freely while controlling your presentation.
Page 48: Controlling Multiple Projectors
Controlling Multiple Projectors If you’re using more than one projector, you can control all the projectors—or just selected ones—by using the projector ID system. To operate a projector, you have to set the remote control’s ID to match that of the projector. Or you can control all of the projectors simultaneously by setting the remote control’s ID to zero.
Page 49: Setting The Remote Control Id
Setting the Remote Control ID The remote control’s default ID is zero. If you need to change it, follow these steps: 1. Press the button on the remote control. You see it light up. 2. Press one of the numbered buttons on the remote control to select the desired ID (0 through 9).
Page 50: Replacing The Batteries
Replacing the Batteries If the projector stops responding to the remote control, check the following: caution If the buttons do not light up, replace the batteries as described below: When replacing batteries, 1. Turn the remote control over. take the following precautions: 2.
Page 51: Controlling The Picture And Sound
Controlling the Picture and Sound You can preview and select your picture sources, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, display a picture-in-picture image, and adjust the brightness and volume. Switching Between Picture Sources If your projector is connected to more than one computer and/or video source, you can switch between the different sources: On the projector’s control panel, there are two...
Page 52: Previewing Picture Sources
Previewing Picture Sources You can use the Preview function to help you select the image source. 1. Press note Movies are displayed as still images on the preview screen. Currently selected source note A red highlight surrounds the preview window for the currently selected source.
Page 53: Turning Off The Picture And Sound
Turning Off the Picture and Sound You can use the button on the remote control to turn off A/V Mute the image and sound and darken your screen. (If you’ve connected an external monitor to the projector, it will continue displaying.) This feature is useful if you want to temporarily redirect your audience’s attention without the distraction of a bright screen.
Page 54: Displaying A Picture-In-Picture Video
Displaying a Picture-in-Picture Video If you’re displaying an image from equipment connected to the DVI, note Computer 1, Computer 2, or BNC port, you can open up a smaller Depending on your picture-in-picture (P-in-P) window on the screen. This window can equipment’s ports, you may display video from either the Video or S-Video port.
Page 55: Adjusting The Brightness
Adjusting the Brightness If you’re presenting in a small room, you may find the brightness of the projector to be too intense. You can adjust it to a more comfortable level using the projector’s menu system: 1. Press the button on the remote control. Menu 2.
Page 56: Highlighting Your Presentation
Highlighting Your Presentation You can display a pointer to call out something on the screen, or draw straight or curved lines to emphasize particular points. There are three preset pointer tools you can choose from, and each one can be customized for a different look.
Page 57: Customizing The Pointer Tools
Customizing the Pointer Tools You can customize the shape and size of each of the three pointer tools, select the color and width of the line made with each pointer, and set how fast you can move the pointer across the screen. 1.
Page 58: Operating Your Computer With The Remote Control
Operating Your Computer with the Remote Control If you’ve connected a computer as described in Chapter 1, you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering PowerPoint and other slideshow-style presentations, since you won’t have to stand next to the computer to change slides.
Page 59: Creating Your Own Startup Screen
Creating Your Own Startup Screen You can transfer any image from your computer or video source to the projector, and then use it as your startup screen. You can also use it as the screen to be displayed when the projector is not receiving a signal or when you press the A/V Mute company logo, slogan, photograph, or any other image you want to...
Page 60: Choosing When To Display The Image
5. Use the arrow buttons to select a zoom rate (display size), and 6. When the message “Save image as user’s logo?” appears, select 7. When you see the message “Completed,” press Choosing When to Display the Image After your image is saved, you can set it up as the startup screen, or the screen you see when there’s no signal or when you press the button (see page 53).
Page 61: Fine-Tuning The Projector
Fine-tuning the Projector ou can use the projector’s on-screen menus to adjust the image, sound, and other features. This chapter covers the following information: Using the menu system Adjusting the image quality Adjusting the image size, shape, and position Adjust the color Adjusting the sound Customizing projector features Fine-tuning the Projector...
Page 62: Using The Menu System
Using the Menu System You can use the remote control (or the projector’s control panel) to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button note You can also use the buttons on the projector to access the menu system: Menu...
Page 63: Restoring The Default Settings
4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the button to see a sub-screen for changing Enter the setting. Press the left or right side of the a slider bar.
Page 64: Adjusting The Image Quality
Adjusting the Image Quality You can use the Video menu to adjust the brightness, sharpness, and contrast. If you’re projecting from a computer (but not through the DVI port), there are additional adjustments you can make (see page 65). 1. Press the 2.
Page 65: Adjusting Computer Images
Adjusting Computer Images When you’re projecting an analog RGB computer image, there are several additional settings you can use to adjust the image. Auto button If your computer image doesn’t look correct, press the button on the remote control Auto (or the button on the projector).
Page 66 Preset button Fine-tuning the Projector 4. Adjust the setting to reduce blurriness by pressing the Sync left or right side of the pointer button. (Be sure to adjust the tracking first for best results.) Resolution (in the Video menu) If your image is distorted (compressed, stretched, partially cut off, or doesn’t completely fill the display area), the projector’s resolution setting may not match that of your computer.
Page 67: Adjusting The Image Size, Shape, And Position
Adjusting the Image Size, Shape, and Position Whether you’re projecting from a computer or video player, you can use these settings to adjust the size, shape, and position of the image. Resize button Adjusts how an image fits into the display area. For computer images, resizing is normally unnecessary, since the projector automatically resizes the image to make the best use of the display area.
Page 68: Adjusting The Color
Adjusting the Color The projector provides several ways for you to adjust the color: Color Mode button Fine-tuning the Projector Color Mode button (also in the Video menu) Lets you quickly adjust the color and brightness for various environments. Use either the remote control or the setting in the Video menu.
Page 69: Adjusting The Sound
Adjusting the Sound You can use the Audio menu to adjust the sound volume or treble/bass balance. 1. Press the button on the remote control, then enter the Menu menu. Audio You see the Audio menu screen: 2. Use the pointer button to highlight the desired option, then adjust it as needed: Volume...
Page 70: Customizing Projector Features
Customizing Projector Features You can use the menu system to change the video signal input at certain ports, turn on or off sleep mode, adjust the network settings, change the language, and customize several other features. Image Setup Options Use these settings to change how the projector processes incoming video signals.
Page 71: Communication Setup Options
24 frames per second (fps) and convert it to 60 fps for a more natural appearance; or select Selecting projects interlaced signals without converting them to progressive, which improves the look of images that contain a lot of movement. BNC Sync Termination (in the Advanced2 menu) This setting should normally be left analog (75-ohm) terminator is required, as for a switcher, change the setting to...
Page 72: Miscellaneous Setup Options
Miscellaneous Setup Options Fine-tuning the Projector that is being used for communication with the computer. Turn off the projector and then turn it back on for the new setting to take effect. No-Signal Msg. (in the Setting menu) Selects a screen color or image to display when the projector is not receiving a signal.
Page 73: Managing The Projector From A Remote Computer
HP OpenView. You’ll need to install a plug-in for your system provided by EPSON, then enter a trap To use the EasyManagement software, first install it as described on IP address using the SNMP page 74. Then connect and configure each projector you want to option in the projector’s...
Page 74: Installing The Easymanagement Software
Installing the EasyManagement Software The projector software CD-ROM includes the software you need to use the projector’s EMP Monitor and EMP Network Manager. System Requirements Before you install the software, make sure your computer meets these note requirements: The software cannot be installed on Macintosh systems.
Page 75 2. Click the button to advance to the next screen. 3. If you want to receive e-mail notifications when projector problems occur, make sure the option to install is highlighted, then click the Manager instructions on the screen to finish installing it. 4.
Page 76: Connecting And Configuring The Projector
Connecting and Configuring the Projector Before using the EMP software to manage your projector(s), you have have to connect each projector you want to monitor to your network and configure it with an appropriate IP address. 1. Connect the projector to your network using a commercially 2.
Page 77 5. If your network does not assign addresses automatically, turn off and enter the projector’s DHCP , as needed. Gateway Address To enter numbers using the remote control, press the button until it lights, then use the number keypad shown below.
Page 78: Using Emp Monitor
Using EMP Monitor EMP Monitor lets you manage up to 64 projectors from a remote computer. This lets you easily turn the projectors on or off (together or individually), switch image sources, and check on their status. Before using EMP Monitor, make sure you’ve installed the software as described on page 74.
Page 79 2. Click as shown. Register projector You see this screen: 3. Click to locate projectors currently operating on the Auto detect network. Or click Manual registration name and network address. Any projectors found on the network are listed as shown below: 4.
Page 80: Monitoring Your Projectors
You see your registered projectors listed on the main EMP Monitor note screen: To delete a projector from the list, click Register , highlight the projector projector name, and click Delete Monitoring Your Projectors note The EMP Monitor screen lets you monitor your projectors using the To monitor a projector Status, Video Source, and Error icons shown below.
Page 81 The following table explains the meaning of the status icons: Status icons (green) Projecting; no problems (dark) Turned off; no problems (green) Projecting; problems detected (dark) Turned off; problems detected Network error (for example, not connected to network, or power cable disconnected). You may also see this error if Standby Mode is turned off (see page 71).
Page 82: Controlling Your Projectors
The following table explains the meaning of the error icons (see page 101 for recommended solutions to problems): Error icons Controlling Your Projectors The control buttons in the upper-right let you turn on and off the note projectors and select video sources. (Hold the mouse pointer over a To turn on a projector when button to see a description of its meaning.) Make sure you’ve selected it’s in standby mode...
Page 83: Configuring The Monitoring Interval
Configuring the Monitoring Interval If you need to have the most current status information about your projectors, click the button in the EMP Monitor screen. Refresh You can also select how often EMP Monitor checks the projector status: 1. From the Tool menu, select You see this screen.
Page 84: Using Emp Networkmanager
Using EMP NetworkManager You can use EMP NetworkManager to send out messages by e-mail, notifying you when a problem occurs with a projector. Before running EMP NetworkManager, make sure you’ve installed the software as described on page 74. Then follow the steps below to create e-mail settings for each projector you want to monitor.
Page 85: Setting A Password
3. If you’d like to register a projector manually and you know its IP address, click the Projector address selection You see this screen: 4. Enter the projector’s IP address and click icon is added to the EMP NetworkManager screen. Setting a Password You can set a password to restrict access to each projector from EMP NetworkManager:...
Page 86: Creating The E-Mail Settings
Creating the E-Mail Settings 1. If 2. Double-click the icon for the projector whose e-mail settings you 3. EMP NetworkManager connects to the projector, and you see note The projector must be plugged in (projecting or in standby mode) for you to be able to connect to it.
Page 87 You can give the projector a name—up to 15 characters long—using alphanumerics only, including the hyphen (-). Naming the projector helps you identify it in EMP Monitor and EMP NetworkManager. This is especially useful if you’re managing more than a few projectors. 5.
Page 88: Understanding The Notification Messages
Understanding the Notification Messages If a projector experiences a problem, it sends an e-mail message to each of the addresses you provided using EMP NetworkManager. The message includes the heading “EPSON Projector” in the subject line. The body of the message contains: note...
Page 89: Maintaining The Projector
Maintaining the Projector regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image. You also need to periodically clean the air filter on the side of the warning projector. A clogged air filter can block ventilation needed to cool the Before you clean any part of projector.
Page 90: Cleaning The Lens
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord. Maintaining the Projector Use a canister of compressed air to remove dust. To remove dirt or smears on the lens, use lens-cleaning tissue.
Page 91: Cleaning And Replacing The Filters
Cleaning and Replacing the Filters The projector has several filters that should be cleaned periodically to remove trapped dust. If the filters become clogged, the projector can overheat and damage can result. Clean the filters approximately every three months, or after every 100 hours of use; clean them more often if you use the projector in a dusty environment.
Page 92: Cleaning The Air Intake Filters
Contact your dealer or call EPSON at (800) 873-7766 in the United States to obtain new ones. In Canada, please call (800) 463-7766 for dealer referral.
Page 93 3. Remove each filter from its holder by releasing the two tabs, as shown. 4. Install new filters in the holders, aligning the tabs with the slots on each side. 5. Slide the assembled filters back into the projector. Tabs Maintaining the Projector...
Page 94: Replacing The Lamp
Turn the projector off when not in Contact your dealer or call EPSON at (800) 873-7766 in the United use. Continuous 24-hour- States for a replacement lamp. Request part number a-day use may reduce the Canada, please call (800) 463-7766 for dealer referral.
Page 95 5. Loosen the lamp cover screws (you don’t need to take them out all the way). Then remove the cover. 6. Loosen the three screws holding the lamp in place (you can’t remove them). 7. Grasp the wire handle as shown and pull the lamp straight out. 8.
Page 96: Resetting The Lamp Timer
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menu. 1. Press the 2. Use the note The lamp usage timer shows 0H until you’ve used the lamp for at least 10 hours. 3.
Page 97: Transporting The Projector
(An optional shipping case is available from EPSON; see page 12.) It’s a good idea to turn off the remote control before packing it in a carrying case.
Page 98 Maintaining the Projector...
Page 99: Solving Problems
Solving Problems you how to contact technical support for problems you can’t solve yourself. If the projector is not working correctly, first look at its status lights note and check for possible solutions on page 100. If you’re having a You can also get on-screen problem with the image or sound, see page 104;...
Page 100: Checking The Projector Status
Checking the Projector Status If you’re having a problem with the projector, check the following: What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. If the projector seems to be indicating a problem, locate the pattern of lights in the table on the next page, then follow the recommended solutions.
Page 101 Use this table to interpret the projector’s status lights, then follow the instructions provided: Status lights Light Description and solution If no lights are on, make sure the power cord is connected securely both at the power outlet and the projector. If you have just replaced the lamp, make sure the cover is securely fastened When the power light is orange, the projector is in sleep mode.
Page 102 Then plug the power cord back in and press the If the projector continues to overheat, contact EPSON for help (see page 110). Warning: Except as specifically explained in this User’s Guide, do not attempt to service this product yourself.
Page 103: Viewing The 'About' Menu Screen
Viewing the ‘About’ Menu Screen Use the About menu to view information on the display settings of your computer and the number of hours the lamp has been used. To access the About menu: 1. Press the button. You see the projector’s main menu Menu screen.
Page 104: Solving Problems With The Image Or Sound
Solving Problems with the Image or Sound You cannot turn on the projector. The projector is powered on, but not projecting an image. Solving Problems If you’re trying to turn on the projector using the remote control, the remote control may be switched off (there’s an on/off switch on its side) or low on battery power.
Page 105 You see the message No Signal Make sure the cables are connected correctly, as described in Chapter 1. If you’ve connected a video player, make sure it’s turned on and playing. If you’ve connected a laptop computer, make sure it’s set to display on an external monitor (see page 35).
Page 106 The image is stretched, compressed, cut off, or doesn’t fit on the screen. The image isn’t square, but tapered on the sides. If you can’t place the projector this way, correct the shape using the Quick Square feature in the projector’s menu system (see page 41). Solving Problems Press the button on the remote control to make sure the...
Page 107 The image contains static, noise, or distortion. If you’re using a video player, make sure the correct is selected in the Video menu (see page 70). If you’re using a computer, press the control) or the Auto/Enter automatically resets the tracking, sync, position, and resolution. If you’re using a computer cable longer than 6 feet (2 meters), or an extension cable, the image quality may be reduced.
Page 108 The colors of the image are not right. note Because of the different technologies used, your projected image may not exactly match the colors on your laptop or computer monitor. There is no sound. Solving Problems If you’ve connected equipment to the Computer 1, Computer 2, or BNC port, make sure the correct Setting menu (see page 70).
Page 109: Solving Problems With The Remote Control
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. Make sure the remote control is turned on using the switch on its side (see page 46). Make sure the remote control ID matches the ID of the projector you want to operate (see page 48).
Page 110: Where To Get Help
24 hours a day, as listed in the following table. Service Access World Wide Web From the Internet, you can reach EPSON’s product support page at http://support.epson.com. After selecting your product, you can access troubleshooting information, download product documentation, and receive technical advice through e-mail.
Page 111: Appendix A: Projector Installation
Appendix A: Projector Installation permanent location, such as a theater or conference room. Placement and Mounting Guidelines The projector can be installed for four different viewing setups: front projection, ceiling mounting, rear projection onto a semi-transparent screen, or rear/ceiling projection, as shown: Front projection Rear projection To project from overhead, you’ll need the optional ceiling mounting...
Page 112: Image Size And Projection Distance
Lens Shift note the image, since it won’t produce keystone distortion, which must be If you’ve installed the eliminated electronically. wide-angle rear projection lens, you won’t be able to use If you mount the projector on the ceiling above screen level, you’ll the projector’s Focus, Zoom, have to tilt it down to center the image on the screen.
Page 113: Image Size Calculations (For All Lenses)
Image Size Calculations (For All Lenses) Use the formulas in this section to estimate the required screen size and placement of the projector, depending on the type of lens with which your projector is equipped. For all lenses except Rear Projection Wide, the image size can be adjusted with the Zoom function, as indicated by the minimum and maximum calculations.
Page 114 Middle Throw Zoom Lens (V12H004M01) Image size: 60 to 600 inches (1.52 to 15.24 m) Projection distance (focal range): 114 to 1791 in. (2.90 to 45.49 m) Middle Throw Zoom Lens (V12H004M02) Image size: 60 to 600 inches (1.52 to 15.24 m) Projection distance (focal range): 170 to 2640 in.
Page 115: Converting Between Diagonal Size And Width Or Height
Converting Between Diagonal Size and Width or Height The calculations on the previous pages use the diagonal length of an image to indicate its size. Use these formulas if you want to find out the diagonal size of a 4:3 image from its width or height: Diagonal size = 5/4 ×...
Page 116: Installing The Rear Cable Cover
Installing the Rear Cable Cover If you’re mounting the projector on the ceiling, install the rear cable cover to enhance the appearance of the system. To install the cover, insert its tabs into the slots as shown, then push the cover against the projector until it locks into place.
Page 117: Appendix B: Technical Specifications
Appendix B: Technical Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels Diagonal: 1.4 inches (35.6 mm) Lens F=1.7 to 2.2, f=53 to 72 mm Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 24 bit, 16.8 million colors Brightness Approx.
Page 118: Projection Lamp
Projection Lamp Type Power consumption Lamp life Part number Remote Control Range Battery Mouse Compatibility Dimensions Height Width Depth Weight Electrical Rated frequency Power supply Power consumption Appendix B: Technical Specifications UHE (Ultra High Efficiency) 320 W Approx. 3000 hours (low brightness); 2000 hours (high brightness) V13H010L23 about 30 feet (10 meters)
Page 119: Computer Video Port Pin Assignments
Environmental Temperature Operating: 41 to 104°F (5 to 40°C) Storage: 14 to 140 °F (-10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Operating altitude 0 to 10,000 ft (0 to 3,048 m) Safety United States FCC 47CFR Part 15B Class B (DoC)
Page 120: Compatible Video Formats
Appendix B: Technical Specifications Refresh Rate (Hz) ® ® ® and iBook series systems, and high-end workstations such as ® ™ SPARCstation. 768 pixels, EPSON’s patented SizeWise ® Power Macintosh series ® computers, many ™ chip supports...
Page 121 formats. For best results, the computer’s resolution should be set to match the projector’s native resolution (1024 768). If this resolution isn’t available, select one of the other compatible formats: Windows: Right-click the desktop, select and select a compatible resolution. (For a laptop displaying through an external monitor port, you’ll need to click the button on the Settings tab, then adjust the resolution Advanced...
Page 122 Mode XGA—43i XGA—60 XGA—70 XGA—75 XGA—85 XGA—120 SXGA1—70 SXGA1—75 SXGA1—85 SXGA1—100 SXGA2—60 SXGA2—75 SXGA2—85 SXGA3—43i SXGA3—60 SXGA3—75 SXGA3—85 SXGA+60 SXGA+75 SXGA+85 UXGA—48i UXGA—60 UXGA—65 UXGA—70 UXGA—75 UXGA—80 UXGA—85 iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19—60 MAC19 MAC21 Appendix B: Technical Specifications Refresh Rate (Hz) Resolution 1024...
Page 123: Appendix C: Notices
Appendix C: Notices his appendix includes safety instructions and other important information about your EPSON PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: Do not place the projector on an unstable cart, stand, or table.
Page 124 Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.
Page 125: Remote Control Information
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: There is an object between the remote control IR emitter and the IR receiver on the projector.
Page 126: Declaration Of Conformity
Trade Name: Type of Product: Projector Model: Marketing Name: PowerLite 8300i Appendix C: Notices EPSON AMERICA, INC. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806-2469 (562) 290-5254 EPSON EMP-8300...
Page 127: Fcc Compliance Statement
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 128: Warranty
(e.g., fuses), other than lamps. This warranty is not transferable. EPSON is not responsible for warranty service should the EPSON label or logo or the rating label or serial number be removed or should the product fail to be properly maintained or fail to function properly...
Page 129 To locate the Authorized EPSON Servicer nearest you, call the EPSON Connection at (800) 637-7661 + PIN or (562) 276-4394 in the U.S. and (905) 709-3839 in Canada or write to: Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012. Appendix C: Notices...
Page 130 Appendix C: Notices...
Page 131: Index
Index A/V Mute, 59 to 60 A/V Mute button, 53 About menu, 96, 103 Accessories, 12, 110 Air filters, cleaning and replacing, 91 to 93 Anti-theft device, 12, 15 Aspect ratio, 117 Audio adjusting tone, 69 adjusting volume, 55, 69 problems, troubleshooting, 108 turning off (using A/V Mute), 53 Bass, adjusting, 69...
Page 132 Environmental specifications, 119 EPSON accessories, 12, 110 PrivateLine Support, 8, 110 technical support, 8, 110 External monitor, connecting, 28, 71 E-Zoom button, 53 FCC compliance statement, 127 Filters, see Air filters Focusing, 38 Foot release button, 39 Freeze button, 53...
Page 133 Navigation buttons, 47 Network settings, 71, 76 to 77 New Hardware Wizard, 33 No-Signal Msg setting, 60, 72 Options for projector, 11 to 12 Picture source, selecting, 34, 51 to 52 Picture, see Image Picture-in-Picture function, 54 Pin assignments, connector, 119 Pointer tool, 56 to 57 Positioning image, 39 to 40...
Page 134 Safety instructions, 123 to 124 specifications, 119 Screen blank, 35 distance from projector, 14, 112 to 115 options, 12 Screen image See Image Setup options, 70 to 72 Shipping case, 12, 97 Sleep mode, 43, 72, 118 SNMP (Simple Network Management Protocol), 73 Software installation, 74 to 75 Sound...
Page 135 Zoom ratio, 117 Zooming image, 38, 53 Index...
Page 136 Index...
Page 137: Control Panel
Projector EasyMP.net option access panel Status lights Handle Speaker Foot release button Control Panel Activates menu system Turns Projector on and off Switches between equipment connected to ports Press and hold to use arrow buttons to adjust Tracking and Sync Squares up tapered image Control panel (see below)
Page 138: Remote Control
Remote Control E-Zoom Enlarges section of image A/V buttons Control image and sound Light button Illuminates remote control buttons Enter and Escape Use as mouse buttons or to make menu selections Menu Activates menu system Preview Displays active image sources Focus, Zoom, Lens Shift Adjust projector optics Volume...

This manual is also suitable for:

Powerlite 8300i V11h068920 Powerlite 8300i/nl

Epson PowerLite 8300NL User Manual

1 Setting up the Projector

2 Displaying and Adjusting the Image

3 Giving Your Presentation

4 Fine-Tuning the Projector

5 Managing the Projector from a Remote Computer

6 Maintaining the Projector

7 Solving Problems

Appendix A: Projector Installation

Appendix B: Technical Specifications

Appendix C: Notices

Quick Links

Related Manuals for Epson PowerLite 8300NL

Summary of Contents for Epson PowerLite 8300NL

This manual is also suitable for:

Table of Contents