Cgeneral Information; Introduction; Definitions; Machine And Manufacturer's Identification Data - Electrolux ESR20EL5 User Manual

Residual risk Description of hazardous
situation
Breakage or bursting Accidental knocking of the cap on
of cap/cylinder
the cylinder and/or dropping of the
cap when changing the keg (possi-
ble cracking of the material)
Lack of required maintenance as
provided for in the relevant sec-
tions. Parts subject to wear not
checked and/or replaced.
Falling from above The operator intervenes on the
machine using unsuitable systems
to access the upper part (e.g. rung
ladders, or climbs on it)
Crushing or injury The specialised personnel may
not correctly fix the control panel
when accessing the technical
compartment. The panel could
close suddenly.
Crushing or injury During lifting of the cylinder, the
operator's hand could get
squashed between the cylinder
and the top of the cabinet. There-
fore do not place a hand on the
cylinder during this stage.
Crushing or shearing Possible risk of injury to upper
limbs during the hood closing
operation.
C GENERAL INFORMATION
C.1

Introduction

Given below is some information regarding the intended use of
this appliance, its testing, and a description of the symbols
used (that identifies the type of warning), the definitions of
terms used in the manual and useful information for the
appliance user.
C.2

Definitions

Listed below are the definitions of the main terms used in the
manual. It is advisable to read them carefully before use.
Operator machine installation, adjustment, use,
maintenance, cleaning, repair and trans-
port personnel.
Manufacturer Electrolux Professional Chinaor any other
service centre authorised by Electrolux
Professional China.
Operator for an operator who has been informed and
normal trained regarding the tasks and hazards
machine use involved in normal machine use.
Customer an operator instructed/trained by the
Care service Manufacturer and who, based on his
or specialised professional and specific training, experi-
technician ence and knowledge of the accident-
prevention regulations, is able to appraise
the operations to be carried out on the
machine and recognise and prevent any
risks. His professionalism covers the
mechanical, electrotechnical and elec-
tronics fields.
Danger source of possible injury or harm to health.
Hazardous any situation where an operator is
situation exposed to one or more hazards.
Risk a combination of probabilities and risks of
injury or harm to health in a hazardous
situation.
Protection safety measures consisting of the use of
devices specific technical means (guards and
safety devices) for protecting operators
against risks.
Residual risk Description of hazardous
situation
Crushing or shearing Possible risk of injury to upper
limbs during the closing operation
of the lid on the rear of the
appliance.
Tipping of loads When handling the machine or the
packing containing it, using unsuit-
able lifting systems or accessories
or with the unbalanced load
Chemical (refrigerant Inhalation of refrigerant gas.
gas) Therefore always refer to the appli-
ance labels
Chemical Contact with chemical substances
(e.g. detergent, rinse aid, scale
remover, etc.) without taking
adequate safety precautions.
Therefore always refer to the
safety cards and labels on the
products used.
IMPORTANT
In case of a significant anomaly (e.g. short circuits,
wires coming out of the terminal block, motor
breakdowns, worn electrical cable sheathing, etc.)
the operator must immediately deactivate the
machine.
Guard an element of a machine used in a specific
way to provide protection by means of a
physical barrier.
Safety device a device (other than a guard) that elimi-
nates or reduces the risk; it can be used
alone or in combination with a guard.
Customer the person who purchased the machine
and/or who manages and uses it (e. g.
company, entrepreneur, firm).
Emergency a group of components intended for the
stop device
emergency stop function; the device is
activated with a single action and pre-
vents or reduces damage to persons/
machines/property/animals.
Electrocution an accidental discharge of electric current
on a human body.
C.3 Machine and Manufacturer's identification
data
An example of the marking or dataplate on the machine is
given below:
The dataplate gives the product identification and technical
data; listed below is the meaning of the various information
given on it.
F.Mod. factory description of product
Comm.Model commercial description
PNC production number code
Ser.No. serial number
380-400 3N power supply voltage
9