Electrolux SkyLine ChillS 202 User Manual page 16

4. Precooling (or preheating) starts.
M N S
NOTE!
This phase can be enabled or disabled in chapter
E.12 Settings mode (Manual ⇨ General, ⇨
Precooling).
7 7
Fan Fan Conserve Conserve Cruise Cruise Turbo Turbo
speed speed c illing c illing cooling cooling
Guide- Norms ela ed ela ed Save
a
lines s ar s ar program
5:30 5:30 -10°C -10°C -20°C -20°C
PM PM
Precooling and preheating functions prepare the cavity
temperature before the beginning of the selected cycle.
Skip Precooling/Preheating
Skip the preparation and go immediately to the main cycle.
7 7
5. At the end of Precooling/Preheating:
Fan Fan Conserve Conserve Cruise Cruise Turbo Turbo
speed speed c illing c illing cooling cooling
a. Insert the food in the appliance and close the door to start
the cycle (TIME CYCLE);
b. Insert the food in the appliance, the food probe in the
Guide- ela ed ela ed Save
Guidelines
lines s ar s ar program
product and close the door to start the cycle (PROBE
CYCLE);
5:30 6:30 -10°C -10°C -20°C -20°C
PM PM
At the end of the cycle, an acustic signal is activated and a
MAN UAL
pop-up window opens showing the following message:
Energy consumption in kWh
Time duration in hours : minutes : seconds
Reference standard used (for example UK)
The check with the standard is successful
Reference standard used (for example UK)
The check with the standard is not successful
Touch the to close the pop-up window.
6. The appliance keeps holding.
(only if the cycle provides for holding phase)
If it is necessary to change some default parameters in
the cycle proceed as follows:
• Change or disable Reference Standards (Norms)
16
7 7
Precooling
UK
Fan Fan Conserve Conserve Cruise Cruise Turbo Turbo
7
speed speed c illing c illing cooling cooling
°C
b
0°C Save
Norms Guide- ela ed ela ed
lines s ar s ar program
6:30 5:30 -10°C -10°C -20°C -20°C
PM PM
7 7
Fan Fan Conserve Conserve
speed speed
Guide- Delayed Delayed
Norms
lines
5:30 6:30
PM PM
USER
Cycle done!
Now holding
5.7 kWh
00:35:00
UK
If a reference standard changes, time and temperature values
change.
M N
To switch the reference standard, proceed as follow:
– Open lower drawer;
– Select Norms icon and choose the required reference
standard, moving with the arrows;
Fan Fan
speed speed
Save
program
5:30 5:30
– Touch the
There are two ways to disable the Norms:
a. from lower drawer
NF
Cruise Cruise Turbo Turbo
chilling chilling cooling cooling
Save
start start program
-10°C -10°C -20°C -20°C
b. from Settings mode (see chapter E.12 Settings mode).
• Change/Set the TEMPERATURE
– Touch the row of the temperature value; select the required
temperature on the numeric keypad, choosing between Soft
or Hard options.
MAN UAL
1
01:30
S
7 7
Norms Guide-
Conserve Conserve Turbo Turbo
lines
cooling cooling
-10°C -10°C -20°C -20°C
PM PM
to confirm and close the pop-up window.
7 7
NF
Fan Fan Conserve Conserve Turbo Turbo
speed speed cooling cooling
Save
program
5:30 6:30 -10°C -10°C
PM PM
MAN
Chill
0
°C
Soft / Hard
:00
7 7
Fan Fan Conserve Conserve Turbo Turbo Guide-
Norms
speed speed cooling cooling lines
UK
Save
program
6:30 5:30 -10°C -10°C -20°C -20°C
PM PM
Norms Guide-
lines
-20°C -20°C
UAL
0
°C
1
1 2 3
Ha rd Chill
c
- 4 20 5 ° 6
7 8 9
1:30
0
+/-
h:m
Soft Hard