Grizzly T33307 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Planer
  5. T33307
  6. Owner's manual
Grizzly T33307 Owner's Manual

Grizzly T33307 Owner's Manual

20v hand planer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL T33307
20V HAND PLANER
OWNER'S MANUAL
(For models manufactured since 06/22)
*Battery not
included
COPYRIGHT © JUNE, 2022 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#SSCS22314 PRINTED IN CHINA
V1.06.22
***Keep for Future Reference***

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T33307 and is the answer not in the manual?

Questions and answers

Related Manuals for Grizzly T33307

Summary of Contents for Grizzly T33307

  • Page 1 COPYRIGHT © JUNE, 2022 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #SSCS22314 PRINTED IN CHINA V1.06.22 ***Keep for Future Reference***...
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Section 1: Safety

    Operating tools in when operating or observing machinery to these areas greatly increases risk of acci- reduce the risk of eye injury or blindness dents and injury. from flying particles. Everyday eyeglasses are not approved safety glasses. Model T33307 (Mfd. Since 06/22)
  • Page 4 FORCING TOOLS.. Use right tool for job, forming the intended operation, stop and do not force it. It will do job safer and using the machine! Contact our Technical better at rate for which it was designed. Support at (570) 546-9663. Model T33307 (Mfd. Since 06/22)
  • Page 5 Plane in same direction or at slight angle with wood grain. Model T33307 (Mfd. Since 06/22)
  • Page 6 Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results. Model T33307 (Mfd. Since 06/22)

  • Page 7: Section 2: Introduction

    For your convenience, we post all avail- Grizzly Industrial, Inc. able manuals and manual updates for free C/O Technical Documentation Manager on our website at www.grizzly.com. Any P.O. Box 2069 updates to your model of machine will be Bellingham, WA 98227-2069 reflected in these documents as soon as Email: manuals@grizzly.com...
  • Page 8 Grizzly PRO 20V Lithium-Ion battery. from coming into contact with surface planer rests on when not in use. F. ON/OFF Trigger: Starts/stops motor. To reduce your risk of serious injury, read this entire manual BEFORE using tool. Model T33307 (Mfd. Since 06/22)

  • Page 9: Section 3: Setup

    This tool presents serious injury the tool and have resolved any issues hazards to untrained users. Read between Grizzly or the shipping agent. You through this entire manual MUST have the original packaging to file a become familiar with the controls freight claim.

  • Page 10: Dust Collection

    The Model T33307 is equipped with a 1 ⁄ " If you cannot find an item on this dust port that can attach to a dust collec- list, carefully check around/inside tion system or shop vacuum.
  • Page 11 Charging/Installing Installing Battery in Planer Battery 1. Press battery lock (see Figure 5) and remove battery from charger. Battery The Model T33307 is compatible with Battery Grizzly PRO 20V Lithium-Ion batteries Lock (see Accessories on Page 17). Removing/Charging Battery 1. Press battery lock (see Figure 3) and remove battery from planer.
  • Page 12 ON/OFF trigger and dis- connect battery. Replace or repair 1. Clear away all setup/adjustment tools. trigger lock so it disables trigger switch before using tool. 2. Install battery in planer (see Charging/ Installing Battery on Page 9). Model T33307 (Mfd. Since 06/22)

  • Page 13: Section 4: Operations

    Read books/magazines or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. Model T33307 (Mfd. Since 06/22)

  • Page 14: Workpiece Inspection

    Workpiece Inspection Adjusting Depth of Cut Some workpieces are not safe to use or The depth of cut on the Model T33307 may require modification before they are. can be adjusted by rotating the depth Before cutting, inspect all workpieces knob to raise or lower the front shoe.

  • Page 15: Installing Fence

    Figure 11. Front shoe flush with workpiece. — If using fence as edge guide, loos- en fence scale lock knob, adjust fence against workpiece, then tighten lock knob (see Figure 12 Figure 10. Fence installed. on Page 14). Model T33307 (Mfd. Since 06/22)
  • Page 16 3. Install depth gauge with depth gauge come to a stop while rear shoe rests lock knob (see Figure 15). on workpiece, then lift planer and inspect workpiece. 9. Repeat Steps 5–8 until desired result is achieved. Model T33307 (Mfd. Since 06/22)
  • Page 17 (see Figure 16). Cutterhead come to a stop while rear shoe rests should not contact workpiece. on workpiece, then lift planer and inspect workpiece. 12. Repeat Steps 7–11 until depth gauge contacts workpiece desired rabbeting depth is achieved. Model T33307 (Mfd. Since 06/22)
  • Page 18 Chamfering Operations The front shoe of the Model T33307 has three machined V-grooves to allow for edge chamfering. To cut a chamfer is to cut away the corner of a workpiece to add a beveled edge between the two workpiece V-Groove surfaces (see Figure 18).

  • Page 19: Section 5: Accessories

    These chargers are compatible with the Installing unapproved accessories T30304 and T30305 batteries used with may cause tool to malfunction, the 20V Grizzly PRO cordless power tool resulting in serious personal inju- lineup. ry or tool damage. To reduce this risk, only install accessories recom- mended for this tool by Grizzly.

  • Page 20: Section 6: Maintenance

    The Model T33307 cutterhead has two reduce the risk of injury due to tool reversible knives. If damage occurs to the starting accidentally. knives, they will either need to be reversed or replaced.
  • Page 21 Step and extend over cutterhead without counterclockwise to secure knife. touching front foot (see Figure 27). Move straightedge across full length 9. Repeat Steps 3–6 for remaining knife. of knife. 10. Install tool holder. Model T33307 (Mfd. Since 06/22)

  • Page 22: Checking/Replacing V-Belt

    Belt Large Pulley Small Pulley Figure 30. Location of belt and pulleys. Belt Cover 6. Install belt cover with screws removed in Step 2. Figure 29. Location of belt cover and Phillips head screws. Model T33307 (Mfd. Since 06/22)

  • Page 23: Section 7: Service

    (Page 18). 3. Pulley loose. 3. Secure pulley on shaft. 4. Cutterhead bearings at 4. Replace bearing(s). fault. 5. Motor bearings at fault. 5. Test by rotating shaft; rotational grinding/loose shaft requires bear- ing replacement. Model T33307 (Mfd. Since 06/22)
  • Page 24 Vibration when run- 1. Loose/damaged knives. 1. Re-install replace knives (Page 18). ning or cutting. 2. Damaged V-belt. 2. Replace belt (Page 20). 3. Worn cutterhead 3. Check/replace cutterhead bearings. bearings. 4. Loose/damaged 4. Re-install/replace cutterhead. cutterhead. Model T33307 (Mfd. Since 06/22)
  • Page 25 SECTION 8: PARTS Main 23 24 37-1 37-5 37-6 37-3 37-7 37-4 37-2 Model T33307 (Mfd. Since 06/22) Model T33307 (Mfd. Since 06/22) BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store.

  • Page 26: Main Parts List

    PT33307036 TERMINAL BLOCK Parts breakdown provided for reference only. Not all parts shown are available for purchase. Model T33307 (Mfd. Since 06/22) Model T33307 (Mfd. Since 06/22) BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store.

  • Page 27: Warranty And Returns

    WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

Table of Contents