Vivo DESK-V100EBY Instruction Manual
Vivo DESK-V100EBY Instruction Manual

Vivo DESK-V100EBY Instruction Manual

Electric single motor desk frame
Hide thumbs Also See for DESK-V100EBY:

Advertisement

Quick Links

Electric Single Motor Desk Frame
Instruction Manual
SKU: DESK-V100EBY/WY
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-v100eby
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DESK-V100EBY and is the answer not in the manual?

Questions and answers

Summary of Contents for Vivo DESK-V100EBY

  • Page 1 Electric Single Motor Desk Frame Instruction Manual SKU: DESK-V100EBY/WY Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/desk-v100eby GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com www.vivo-us.com...
  • Page 2 WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury.
  • Page 3 ASSEMBLY STEPS STEP 1 Assemble Right Crossbar (E) to Motorzied Leg (B) and Left Crossbar (D) to Leg (A) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-B). STEP 2 Secure Side Brackets (F) to Motorized Leg (B) and Leg (A) using M8x12mm Screws (S-B) and 5mm Allen Wrench (T-B).
  • Page 4 STEP 3 Assemble Feet (H) to Motorized Leg (B) and Leg (A) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-B). STEP 4 Insert Inner Crossbar (C) into Left Crossbar (D) and Right Crossbar (E). Extend the frame to the desired length and secure using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-B).
  • Page 5 STEP 5 Loosen the nut on Sync Rod (G). Insert the hex shaft on Sync Rod (G) into Leg (A) until it reaches the notch. While holding the hex end of Sync Rod (G), pull the larger rod out until the connector engages with Motorized Leg (B).
  • Page 6 STEP 7 Secure frame assembly and Control Panel (J) to the desktop with M5x16mm Screws (S-C) and a Phillips screwdriver. STEP 8 Connect cables from Motorized Leg (B) and AC Adapter (I) to Control Panel (J) as shown. Remove adhesive backing from Cable Clips (M) and place them on the underside of the desktop to route cables.
  • Page 7 OPERATING CONTROL PANEL OPERATING INSTRUCTIONS: Press the up arrow, the desk will automatically raise to the highest position. Pressing the down arrow will automatically lower the desk to the lowest position. Memory Mode To store a certain height in the controller’s memory, press and hold the 1 button for 5 seconds. "H1" will be displayed, indicating that the current height has been saved to the 1 button sucessfully.
  • Page 8 AVG. RESPONSE TIME (within office hrs) - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com...

This manual is also suitable for:

Desk-v100ewy

Table of Contents