M-system R7 Series Instruction Manual

INSTRUCTION MANUAL
DISCRETE INPUT EXTENSION MODULE, 16 points
(Ethernet Modbus/TCP)
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System's Sales Office or representatives.
■ PACKAGE INCLUDES:
Discrete input extension module ..................................... (1)
■ MODEL NO.
Confirm that the model number described on the product is
exactly what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■ CONFORMITY WITH EU DIRECTIVES
• The actual installation environments such as panel con-
figurations, connected devices and connected wires may
affect the protection level of this unit when it is integrat-
ed in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure CE conformity.
■ POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%, approx. 20mA
■ GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply and input signal for safety.
■ ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■ WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■ AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for sat-
isfying complete performance described in the data sheet.
SEN TRONIC
COMPONENT IDENTIFICATION
■ DISCRETE INPUT STATUS INDICATOR LED
Discrete input extension modules have LED indicators
showing input signal status.
Contact ON: LED ON
Contact OFF: LED OFF
■ INPUT TERMINAL ASSIGNMENT
NO.
1
2
3
4
5
6
7
8
9
056 222 38 18 mailbox@sentronic.com
AG
R7E-EA16
MODEL
Discrete Input Status Indicator LED
10 11 12 13
1 2 3 4 5
10 11 12 13 14 15
NC X1 X3 X5 X7
1 2 3 4 5 6
COM X0 X2 X4 X6 X8
ID FUNCTION NO.
COM Common 10
X0 Input 0 11
X2 Input 2 12
X4 Input 4 13
X6 Input 6 14
X8 Input 8 15
XA Input 10 16
XC Input 12 17
XE Input 14 18
EM-7807-I Rev.2
www.sentronic.com
R7E-EA16
0 1 2 3 4 5 6 7 8 9 A B C D E F
14 15 16 17 18
6 7 8 9
Input Terminals
16 17 18
X9 XB XD XF
7 8 9
XA XC XE
ID FUNCTION
NC No Connection
X1 Input 1
X3 Input 3
X5 Input 5
X7 Input 7
X9 Input 9
XB Input 11
XD Input 13
XF Input 15
P. 1 / 3