Subscribe to Our Youtube Channel
Related Manuals for Struers LaboDoser-100
Summary of Contents for Struers LaboDoser-100
- Page 1 LaboDoser-100 Instruction Manual Original Instructions Doc. no.: 16377025-01_C_en-us Date of release: 2023.02.07...
- Page 2 Copyright The contents of this manual are the property of Struers ApS. Reproduction of any part of this manual without the written permission of Struers ApS is not allowed. All rights reserved. © Struers ApS 2023.02.24. LaboDoser-100...
-
Page 3: Table Of Contents
7.3 Daily 7.4 Spare parts 7.5 Service and repair 7.6 Disposal 8 Troubleshooting 9 Technical data 9.1 Technical data - LaboDoser-100 9.2 Diagrams - LaboDoser-100 9.3 Legal and regulatory information 10 Manufacturer Declaration of Incorporation of Partly Completed Machinery LaboDoser-100... -
Page 4: About This Manual
LaboDoser-100 is intended to be used in combination with: • LaboForce-100 The device is designed to be used with Struers consumables specially designed for this purpose and this type of device. Do not use the device for Other equipment than stated in the section "Intended use". -
Page 5: Safety Messages
The machine must be disconnected from the electrical power supply before any service. Wait 5 minutes until residual potential on the capacitors is discharged. 10. Struers equipment must only be used in connection with and as described in the Instruction Manual supplied with the equipment. -
Page 6: Safety Messages In This Manual
Instruction Manual supplied with the equipment. Getting started Device description LaboDoser-100 is a dosing unit for delivering suspension or lubricant on a preparation disc in the preparation (grinding or polishing) of materials for further materialographic inspection. LaboDoser-100 is controlled by LaboForce-100. -
Page 7: Labodoser-100
4 Transport and storage The device is designed to be used with Struers consumables specially designed for this purpose and this type of device. LaboDoser-100 Front view A Dosing block with nozzles B LaboDoser-100 C Emergency stop (on LaboPol) Rear view... -
Page 8: Long-Term Storage Or Shipping
Easy connectors Set of tubes • 4 short tubes from bottles to pumps • 4 long tubes from pumps to LaboDoser-100 Spiral cable wrap to wrap around the tubes Silicone tubes for the pump for alcohol-based products Instruction Manual set LaboDoser-100... -
Page 9: Installing Labodoser-100
Cleaning the tubes Clean the tubes and easy connectors when you switch between different types of lubricants/suspensions. Hint If the equipment is not to be used for a prolonged period of time, Struers recommends that you clean the tubes. LaboDoser-100... -
Page 10: Maintenance And Service
Change the tubes When you use alcohol-based lubricants, the Novoprene tubes mounted in the pumps will harden over time. Silicone has a better resistance against alcohol. You can replace the tubes with the set of silicone tubes supplied with the unit. LaboDoser-100... - Page 11 Move the white clips and the connector to the new silicone tube. Fit the new tube into the housing and press it firmly into place. Press the three rollers into the pump housing. 10. Mount the tube correctly in the pump. LaboDoser-100...
-
Page 12: Daily
If you have technical questions or when you order spare parts, state serial number and voltage/frequency. The serial number and the voltage are stated on the type plate of the machine. For further information, or to check the availability of spare parts, contact Struers Service. Contact information is available on Struers.com. -
Page 13: Disposal
Note Service must only be performed by a qualified technician (electromechanical, electronic, mechanical, pneumatic, etc.). Contact Struers Service. Service check We offer a range of comprehensive maintenance plans to suit the requirements of our customers. This range of services is called ServiceGuard. -
Page 14: Technical Data
Technical data - LaboDoser-100 Subject Specifications Directives/Safety See the Declaration of Incorporation of Partly Completed Machinery. standards Power supply Power inlet LaboDoser-100 is connected directly to LaboForce-100 Voltage/frequency 1 x 24 V DC Current, nominal load 0.15 A Current, maximum load 0.6 A Current, largest load 0.15 A... - Page 15 9 Technical data 16363050 D LaboDoser-100...
-
Page 16: Legal And Regulatory Information
Responsibility of the manufacturer The following restrictions should be observed, as violation of the restrictions may cause cancellation of Struers legal obligations. The manufacturer assumes no responsibility for errors in the text and/or illustrations in this manual. The information in this manual is subject to change without notice. The manual may mention accessories or parts not included in the supplied version of the equipment. -
Page 17: Declaration Of Incorporation Of Partly Completed Machinery
Based on: 16377903 C Declaration of Incorporation of Partly Completed Machinery Manufacturer Struers ApS • Pederstrupvej 84 • DK-2750 Ballerup • Denmark Name LaboDoser-100 Model LaboDoser-100 Function LaboDoser-100 Dosing unit controlled by LaboForce-100 when mounted on LaboPol-30 or LaboPol-60 Grinding/Polishing machine Type Cat. - Page 18 Tõlked leiate aadressilt Katso käännökset osoitteesta Pour les traductions, voir Za prijevode idite na A fordítások itt érhetők el Per le traduzioni consultare www.struers.com/Library 翻 訳 については、 Vertimai patalpinti Tulkojumus skatīt Voor vertalingen zie For oversettelser se Aby znaleźć tłumaczenia, sprawdź...
Need help?
Do you have a question about the LaboDoser-100 and is the answer not in the manual?
Questions and answers