Table of Contents
Advertisement
EVOHD+ Installation Guide
Introduction
The Digiplex EVOHD+ is a security and access control system with 8 on-board zone inputs (16 with zone doubling) that is expandable to 192 zones via the 4-wire
Digiplex bus. The EVOHD+ control panel features up to 999 users, 8 partitions, 32 doors and can support up to 254 modules in any combination.
The Digiplex EVOHD+ system provides the highest level of protection for banks, high-security military and government sites, luxurious residential homes and any
place where maximum security is essential. These systems are designed to be easy to use, and the modular concept of these systems provides installers with labor-
saving features that make expanding, installing and servicing these systems quick and convenient.
Expand the EVOHD+ system by adding plug-and-play expansion modules anywhere and in any combination on the 4-wire Digiplex bus. Modules are connected to
the Digiplex bus at the most convenient location and then their zone inputs are assigned to the desired zone and partition. Also, only a module's used inputs are
assigned to zones in the system. Keyswitches, remote controls and unused module inputs do not use up zones. Once installed, all Digiplex bus modules, including
motion detectors, can be programmed remotely via a keypad or the BabyWare upload/download software.
EVOHD+ also supports 32 virtual zones in addition to its security zones and access control doors. Virtual zones can be used to automate PGM activations without
occupying a security zone and without affecting the system's security functions. The EVOHD+ system is a logical solution to every installer's security, access control
and home automation installation needs.
Features of
EVOHD+
Digital bus:
•
Provides constant power, supervision and two-way communication between the control panel and all its modules
•
Supports up to 254 expansion bus modules
•
Connect modules up to 914m (3000ft) from the panel
•
Sabotage-proof technology without additional wiring
Expandable to 192 zones
Built-in access control features
In-field firmware upgradeable via 307USB (or IP150+) and BabyWare
Compatible with NEware
Automatic Daylight Saving Time feature
3 on-board solid-state PGM outputs, negative or positive triggering
PGM1 can be used as a 2-wire smoke input
1 Form C relay output with N.O and N.C. contacts.
999 user codes
8 partitions
3584 events buffered
Program remote controls using the master or installer codes
Up to 999 remote controls with one RTX3
Built-in-real-time clock
2.5A switching power supply
1 supervised bell output, auxiliary output and telephone line
Separate Tamper switch input
Fits in a 28 x 28 x 7.6 cm (11 x 11 x 3 in) metal box
Dimensions: 9.5 X 20.2 cm (3.75 X 7.94 in); Weight: 0.49 lbs. (0.22 kg)
Specifications
Control Panel
AC Power:
16Vac, 40/75VA, 50-60Hz
Consumption:
100mA
Battery:
12Vdc, 7Ah minimum
Auxiliary Power:
0.8A typical, 2.0A maximum, fuseless shutdown at 2.5A
Bell Output:
2A, fuseless shutdown @ 2.5A
PGM Output:
PGM1: Open collector output, PGM2,3 and 4 100mA solid-state relays with +/- trigger, PGM5 Form C relay output rated at 3A/28Vdc
N.O. / N.C.
Operational Temperature: -10°C to +55°C (14°F to +133°F)
Weight and Dimensions
in EN metal enclosure:
28.5 x 30 x 8 cm (11 x 11 x 3 In.); 5.2 kg (11.4 lbs)
Accessories
30hrs backup
current *
7AHr
130mA
17AHr
470mA
35AHr
1170mA
*modules current is the sum or the current consumed by all modules
(keypads, detectors...)
60hrs
Recharge to 80%
backup
(@850mA)
N/A
3.7 hrs.
183mA
9 hrs.
583mA
18.7 hrs.
Important Installation Considerations
Maximum Peak to peak ripple voltage on AUX is 500 millivolts.
Low voltage on the battery generated when battery is below 11.7 volts
Deep discharge protection on the battery operates 11 ± 0.3 volts.
If output voltage drops below 11.7 volts a fault is signal is generated.
5
Advertisement
Table of Contents
