Related Manuals for Jetson JJRNY-BLU
Summary of Contents for Jetson JJRNY-BLU
- Page 1 Journey Electric Bike. A guide for your ride. IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY MODEL: JJRNY-BLU Designed in Brooklyn...
- Page 3 Remember to be safe and, most importantly, have fun!
-
Page 5: Table Of Contents
Table of Contents Safety Warnings .......................5 Safety Checklist .......................9 What’s in the Box . -
Page 7: Safety Warnings
Safety Warnings • Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use. • Please check the drive system and frame before riding to ensure safety. •... - Page 8 • Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death. • If the brake loosens, please adjust with the hexagon wrench, or please contact Jetson Customer Care. • Replace worn or broken parts immediately.
- Page 9 For all maintenance repairs and needs beyond the capability of the consumer, which may include but not be limited to: such as proper maintenance of brakes, control cables, bearing adjustments, wheel adjustments, lubrication, reflectors, tires and handlebar and seat adjustments, please contact Jetson Customer Care for assistance at: support.ridejetson.com US &...
-
Page 11: Safety Checklist
ARE NOT BROKEN AND THAT THE AXLE NUTS ARE TIGHT. CHAIN MAKE SURE ALL BEARINGS ARE LUBRICATED AND RUN SMOOTHLY. FRAME AND FORK CHECK THAT THE FRAME AND FORK ARE NOT GENERAL LIMITED WARRANTY IN ANY WAY DAMAGED OR BROKEN. For information about Jetson's General Limited Warranty, visit support.ridejetson.com... -
Page 12: What's In The Box
What’s in the Box 1. HANDLEBAR 9. REAR LIGHT / REAR REFLECTOR 2. LCD DISPLAY 10. PEDALS (2X) 3. HAND BRAKE 11. KICK STAND 4. FRONT HEADLIGHT 12. REAR DISC BRAKE 5. BIKE FRAME 13. FRONT DISC BRAKE 6. CHARGING PORT 14. - Page 13 PLEASE NOTE: IMAGES MAY NOT REFLECT EXACT APPEARANCE OF ACTUAL PRODUCT.
- Page 14 1. LCD DISPLAY 2. FRONT REFLECTOR 3. LEFT BRAKE LEVER—FRONT BRAKE 4. RIGHT BRAKE LEVER—REAR BRAKE 5. DISPLAY CONTROL BUTTONS (POWER, + , - ) 6. BELL 7. LEFT GEAR SHIFTER: 3 GEARS* 8. RIGHT GEAR SHIFTER: 7 GEARS* * 21 GEARS IN TOTAL...
-
Page 15: Specs & Features
Specs & Features • PRODUCT DIMENSIONS: 72 IN × 27 IN × 47 IN • MOTOR: 250W • PRODUCT WEIGHT: 48 LB • MAX SPEED: UP TO 20 MPH • TIRE SIZE: 27.5 IN • MAX RANGE: UP TO 22 MILES •... -
Page 16: Installing Handlebar
1. Get Started Installing the Handlebar • LOOSEN SCREWS ON STEM OF BIKE USING THE ALLEN KEY SCREWS... - Page 17 • MAKE SURE HANDLEBAR IS CORRECTLY CENTERED AND BALANCED. PLACE HANDLEBAR ONTO STEM...
- Page 18 TIGHTEN SCREWS...
-
Page 19: Front Fender Assembly
SCREW FRONT FENDER Front Fender Assembly • ATTACH THE FRONT FENDER WITH SCREW AT THE TOP OF FORK. -
Page 20: Front Wheel Assembly
LEVER SPRING "A" SPRING "B" Front Wheel Assembly • REMOVE NUT AND SPRING "A" FROM QUICK RELEASE SKEWER. • PLACE SPRING "A" AND NUT BACK ONTO SKEWER. - Page 21 MAKE SURE NUT IS SECURE BY TIGHTING IT USING THE DOUBLE SIDED WRENCH.
- Page 22 METAL BRACKETS FRONT WHEEL FRONT FORK • INSERT THE WHEEL INTO THE FRONT FORKS. • MAKE SURE THE WHEEL IS CENTERED AND THAT THE DISC BRAKE IS ALIGNED DIRECTLY NEXT TO THE BRAKE PADS. • ATTACH THE METAL BRACKETS ON THE FENDER TO THE FRONT FORK NEAR AXLE USING SCREWS (NEED TO UNSCREW THE SCREWS AND RESCREW WITH FENDER ATTACHED ON BOTH...
- Page 23 LEVER • TIGHTEN THE NUT. AS YOU TIGHTEN, CONTINUALLY CHECK THE TENSION BY CLOSING THE LEVER. • WHEN YOU FEEL THE LEVER HAS TENSION AT 90 DEGREES FROM THE WHEEL, FULLY CLOSE THE LEVER. NOTE: MAKE SURE THE LEVER IS PARALLEL TO THE FRAME BEFORE RIDING.
-
Page 24: Inserting The Brake
SCREWS BRAKE Installing the Brake • REMOVE SCREWS FROM BRAKE • PLACE BRAKE ON THE WHEEL • TIGHTEN SCREWS... -
Page 25: Inserting The Seat
Inserting the Seat OPEN THE SEAT CLAMP... - Page 26 • SLIDE THE SEAT POST IN. • ENSURE THE SEAT POST REACHES THE MINIMUM INSERTION LINE MARKED ON THE POST. PLACE SEAT INTO SEAT POST...
- Page 27 • TURN THE KNOB CLOCKWISE TO TIGHTEN SEAT. CLOSE THE SEAT CLAMP. TIGHTEN & CLOSE SEAT CLAMP...
- Page 28 MAKE SURE SEAT CLAMP IS SECURED AND SEAT IS STABLE...
-
Page 29: Pedals Assembly
Pedals Assembly INSERT PEDAL MARKED “L” INTO THE RIGHT-HAND CRANK ARM PEDAL... - Page 30 • HAND TIGHTEN SPINDLE ON PEDAL MARKED “L” CLOCKWISE. • REPEAT WITH PEDAL MARKED “R”, TIGHTENING IT COUNTER-CLOCKWISE.
- Page 31 ONCE BOTH PEDALS ARE ON, TIGHTEN WITH WRENCH. CAUTION: IT’S IMPORTANT TO STOP IF YOU FEEL RESISTANCE WHEN PUTTING ON THE PEDALS. IT COULD MEAN THE SPINDLE IS ENTERING THE CRANK ARM AT AN ANGLE AND IT MAY DAMAGE THE THREAD. TIGHTEN...
-
Page 32: Riding The Journey
2. Make Moves Riding the Journey NOW YOU HAVE YOUR BICYCLE SAFELY ASSEMBLED - THE JOURNEY OF A LIFETIME BEGINS! -
Page 33: Operating The Journey
Operating the Journey PLUS BUTTON LCD DISPLAY POWER BUTTON MINUS BUTTON • POWERING ON: PRESS THE POWER BUTTON TO TURN ON LCD DISPLAY. • LIGHT FUNCTION: HOLD PLUS BUTTON FOR 3 – 5 SECONDS TO TURN ON HEADLIGHT. HOLD DOWN FOR ANOTHER 3 – 5 SECONDS TO TURN OFF HEADLIGHT. •... - Page 34 • THE OPTIONS RANGE FROM “0” FOR KMH TO “1” FOR MPH. THE FACTORY DEFAULT SETTING IS 0. • ONCE YOU HAVE PREFERRED OPTION SELECTED, PRESS THE POWER BUTTON TO EXIT. PLEASE CONTACT JETSON SUPPORT IF YOUR STATUS DISPLAY IS SHOWING ANY OF THESE PROMPTS: • P04 - MOTOR HALL SENSOR FAILURE •...
-
Page 35: Helmet Safety
Helmet Safety PROPER POSITIONING: IMPROPER POSITIONING: THE FOREHEAD IS COVERED THE FOREHEAD IS EXPOSED. BY THE HELMET. COULD CAUSE SERIOUS INJURY. * WEAR A HELMET, APPROPRIATE CLOTHING, SHOES, AND SAFETY GEAR. AVOID CLOTHING THAT CAN GET CAUGHT INTO OR UNDER THE WHEELS. CLOSED-TOE, FLAT SHOES ARE RECOMMENDED. WEAR AN ASTM F1492 APPROVED HELMET AND PROTECTIVE GEAR TO PREVENT INJURY IN THE EVENT OF AN ACCIDENT. -
Page 36: Charging The Journey
Charging the Journey CHARGING THE BATTERY A FEW MUST-DO’S: • ONLY USE THE INCLUDED CHARGER • PLUG THE CHARGER INTO THE WALL BEFORE THE CHARGING PORT • DON’T TURN ON THE JOURNEY WHILE IT’S CHARGING • CHARGE THE BATTERY UNTIL IT IS FULLY CHARGED - UP TO 6 HOURS •... -
Page 37: Care & Maintenance
• Avoid intense physical impact and / or severe vibration. • Protect from water or moisture. • Do not disassemble. • If there are any issues with the battery, please contact Jetson Customer Care. We’d love to help! STORAGE • Remove batteries before storing. - Page 38 Stay connected. Be sure to follow @ridejetson on social media to learn about fantastic offers, giveaways, and all the latest Jetson news. Loving your ride? Then be sure to leave a review at ridejetson.com/reviews. We can’t wait to hear from you!
- Page 40 Date Code: 01/2023 Document Edition: v2.1 © 2023, JETSON. ALL RIGHTS RESERVED. Manufactured by JETSON ELECTRIC BIKES LLC. No portion of this document, including shape, copy, graphics, and design, may be reproduced or transmitted in any form or by any means.