Subscribe to Our Youtube Channel
Related Manuals for Vanco Evolution EVMX4044
Summary of Contents for Vanco Evolution EVMX4044
- Page 1 HDMI® 4x4 MATRIX SELECTOR SWITCH (over Cat5e/Cat6 Cable) Vanco Part Number EVMX4044 Quick Install HDMI® 4x4 Matrix Selector Switch (over Single Cat5e/Cat6 Cable) www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 FEATURES INTRODUCTION The Evolution by Vanco Quick Install 4x4 Matrix over Cat5e/Cat6 Cable with RS-232 is an HD switching and extension system that comprises of a 4 input/4 output HD Matrix together with included 4 display receivers. Have 4 sources displayed simultaneously on any display or have a single source duplicated on multiple displays, flexibility for the perfect solution.
-
Page 4: Specifications
SPECIFICATIONS HDCP Compliance ............Yes Video Bandwidth ............Single-link 225Mhz [6.75 Gbps] Video Support ............480i/480p/720p/1080i/1080p @60 36-bit color Audio Support ............Surround Sound (up to 7.1 ch) or stereo digital audio ESD Protection ............[1] Human body model — ±19kV [air-gap discharge] &... -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS Power Switch Source Status: Input source indicator LED 7-segment LED: for output 1-4 status IR SENSOR: IR sensor for receiving the IR commands from IR remote Push Button: Select the output and input Push Button: Enter Button HDMI Local Loopout Port 1-4: Local loopout HDMI outputs for each output channel Output Port 1-4: RJ-45 outputs for each output channel INPUT 1-4: HDMI inputs... - Page 6 RECEIVERS 1. 5V DC: Connect to 5V DC power supply. 2. HDMI OUT: Connect to a HDMI display with a HDMI male-male cable. 3. EQ ROTARY DIAL - If you see flickering or blinking image on the display, adjust the EQ rotary switch to improve the cable skew. MAX stands for the strongest HDMI signal level for the longest possible transmission length while MIN stands for the weakest HDMI signal level for short transmission length.
- Page 7 EDID There are two methods for EDID Learning as shown below: 1. IR Remote Control: Please refer to the Operation Control – IR Remote Control section 2. Software Control: Please refer to the Operation Control - Software Control through RS-232 and LAN port EDID Settings: There are nine embedded default EDID settings as shown below: 1.
- Page 8 OPERATION CONTROL - IR REMOTE CONTROL 1. INPUT/OUTPUT Switch - Push the corresponding button on the remote to select Input & Output port. Ex: Select Input 2 to Output 3 - The button highlighted in the red circle button shown below to select Input 2 to Output 3 2.
- Page 9 800.626.6445...
- Page 10 OPERATION CONTROL - SOFTWARE CONTROL THROUGH RS-232 AND LAN PORT 1. System Requirement 1) OS Information: MS WinXP/7 2) Baud rates: 9600 3) Software size: 3 MB 4) Minimum RAM requirement: 256 MB OPERATION CONTROL – Software control through RS-232 I/O Routing Button Rename I/O Button EDID Button...
- Page 11 1. Input Selection and Mapping I/O: Select the input Click “Send” to change the I/O setting Save Mapping: Select Mapping(1-8) Click “Save” button to save current mapping Preset Mapping: Select Mapping(1-8) Click “Recall” button to recall previous mapping which are saved 800.626.6445...
- Page 12 2. Rename I/O Button Rename I/O: Rename output name Rename input name Rename Mapping: Rename Mapping name www.vanco1.com...
-
Page 13: Edid Button
3. EDID BUTTON Learn EDID from Default Select Default EDID(1-8 Default EDID) Select Input Click “Send” button to learn default EDID Learn EDID From Display Select output Select Input Click “Send” button to learn display EDID Load EDID File to Input Select Input Click “Load”... - Page 14 4. NETWORK Save Setting Save the IP address which is manually entered Read Setting: Read the IP address from the device ** The default IP address is 192.168.1.111 www.vanco1.com...
-
Page 15: System Button
5. SYSTEM BUTTON Firmware Update 1) Version: To get the F/W version information 2) Factory Reset 3) Help: To view the steps of the firmware update 4) Firmware Update Main Board 5) Firmware Update Web IC 6) Firmware Update Front Panel 800.626.6445... -
Page 16: Connection Status
6. COM PORT SELECTION Click “ ” button to select COM Port 7. CONNECTION STATUS Connected Status: Connecting Status: Disconnected Status: 8. CONNECT/DISCONNECT Click this button “ ” to change connection status www.vanco1.com... - Page 17 9. RS-232 Click “ ” button to switch to RS-232 function. If RS-232 is connected, the button emit to show that RS-232 is connected 10. ETHERNET Click “ ” button to switch to Ethernet function If Ethernet is connected, the button will emit to show that ethernet is connected 800.626.6445...
- Page 18 OPERATION CONTROL - WEB INTERFACE CONTROL The default IP address: 192.168.1.111 Account: admin Password: matrix 1. I/O Routing Button 2. Setting Button 3. EDID Button 1) I/O Routing 1) Refresh Mapping 2) I/O: a) Select the input 3) Save Mapping: a) Select Mapping(1-8) b) Click “Save”...
- Page 19 2) Settings 1) Rename I/O: a) Rename output name b) Rename input name 2) Rename Mapping: a) Rename Mapping name 3) Password change: (the password has to be 6 characters) a) Key in “old password” b) Key in “new password” c) Key in “new password”...
-
Page 20: Connection Diagram
CONNECTION DIAGRAM www.vanco1.com... -
Page 21: Connect And Operate
CONNECT AND OPERATE 1. Connect up to 4 sources such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI inputs on the unit. Do not hotplug! Insert and extract cables carefully with the power SWITCHED OFF. Connecting and disconnecting while the unit is powered can result in damage to circuitry. -
Page 22: Ir Pass-Through
IR PASS-THROUGH IR Extenders IR Blaster TX IR Receiver RX IR BLASTER (EV-IRTX) Plug IR Blaster into IR TX port of matrix unit (EVMX4044); place blaster in front of the IR eye of the corresponding source. IR RECEIVER (EV-IRRX) Plug IR Receiver into IR RX port of matrix unit (EVMX4044); place receiver at or near corresponding display. - Page 23 NOTICE 1. Vanco High Speed HDMI cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the unit. Please check carefully before plugging in the IR accessories into the respective IR sockets.
-
Page 24: Troubleshooting
HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. This activates all of the devices in corresponding order and results in a signal being plugged into a device that is on and will attempt to connect the signal. -
Page 25: Safety And Notice
SAFETY AND NOTICE The EVMX4044 has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the EVMX4004 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. -
Page 26: Limited Warranty
Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco. This warranty does not apply to those products which have been damaged due to accident, unauthorized alterations, improper repair, modifications, inadequate maintenance and care, or use in any manner for which the product was not originally intended. -
Page 27: Liability Statement
LIABILITY STATEMENT Every effort has been made to ensure that this product is free of defects. The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use. It is the responsibility of the user and installer of the hardware to check that it is suitable for their requirements and that it is installed correctly. - Page 28 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...
Need help?
Do you have a question about the Evolution EVMX4044 and is the answer not in the manual?
Questions and answers