Page 1
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB713SR-8 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. 44766 Centre Court Clinton Twp. MI 48038 USA GAGE BILT Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 solutions1@gagebilt.com / www.gagebilt.com...
Overhaul ....................................14-16 Parts Lists ................................... 17-18 DEXRON® III Oil Safety Data (SDS) ............................19 Nose Assembly Selection Chart ............................. 20 Accessories ..................................21-24 GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN ISO 12100:2010 EN ISO 13849-2:2012 The Supply of Machinery (Safety) Regulations 2008 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str.
The GB713SR-8 split handle installation tool operates on 90 - 100 psi. (6.2 - 6.9 bar) of air pressure, with 90 psi. (6.2 bar) providing the maximum efficiency. At 90 psi. (6.2 bar) of air pressure, the GB713SR-8 does not exceed 81.5 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle).
Bleed Screw Hydraulic Hose “Pull” Actuator Actuator Lever Assembly Air Line Bleed Screw Handle Assembly Air Inlet Image may not reflect actual tool GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Air Piston moves down Air exhaust Air exhaust Pressurized Oil Unpressurized Oil Pressurized Air Unpressurized Air Images may not reflect actual tool GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
HEAD CYLINDER FASTENER WORK ACTUATOR RED SHIPPING PLUG USER QUICK AIR INLET DISCONNECT FITTING AIR HOSE Image may not reflect actual tool GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Press actuator to start cycle. Release actuator as soon as fastener breaks. Repeat steps 1 - 4. Images may not reflect actual tool or fastener GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants should be avoided.
Handle Assembly and Power Cylinder hole Oil Passage hole O’ring (S832) ***Keep air hole free from oil*** Images may not reflect actual tool. GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Subtract dimension (A) from dimension (B). If stroke is not consistent within 1/64" (.396 mm) repeat bleeding steps until stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke. Please contact Gage Bilt for more information.
Selection Chart pg. 20 to select Stroke Limiter) Tighten End Cap onto tool. (See pg. 10 for torque setting) Images may not reflect actual tool GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.
Page 15
Insert and turn 5/8” open end box wrench / adjustable wrench and snug tight approximately 1/4-1/2 turn. Re-attach the lever assembly (724017) with pin. GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Page 16
Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144). Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152). GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
GB713SR ACCESSORIES Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) NOSE ASSEMBLY SELECTION CHART STRAIGHT RIGHT ANGLE OFFSET Stroke Limiter (Sold Separately) (Sold Separately) (Sold Separately) #713152 Required with all offset...
Page 21
Hand held weight - 2.50 lbs. (1.1 kg) Entire tool weight - 7.50 lbs. (3.4 kg) Pull load - 4,500 (20.0 kN) GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Accessories Cont. Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) Grip Gage #269G3 Grip Gage #GB105093 For CHERRYMAX® and For NAS LOCKBOLTS and CHERRYLOCK® fasteners blind fasteners (Sold Separately)
Page 23
This page intentionally left blank. GB713SR-8 INSTALLATION TOOL S/N: 1024 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. Rev. 1/23...
Page 24
Riveter Kits Available (Sold Separately) Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Split Riveter Tool Backpacks For 5ft hose Split System Tools. (Sold Separately) DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LOCTITE® IS A REGISTERED TRADEMARK OF HENKEL CORPORATION. TEFLON® IS A REGISTERED TRADEMARK OF E.I.